Beurer BC 32 User manual

- Do not use the device near strong electromagnetic fields, keep it away from radio equipment or mobile phones.
1. Getting to know each other
• In the case of limited blood flow to the hand due to chronic or acute vascular diseases (including narrowing of blood
vessels), the accuracy of wrist measurements is limited. In this case, do not use a blood pressure monitor on your arm.
• Batteries do not belong in the household waste. Please take the discharged batteries to the designated collection points.
• We recommend that you remove the batteries if you will not be using the device for a long time.
The determined values are classified and graphically assessed according to WHO guidelines. Keep these operating
instructions for future reference and make them available to other users.
• Only use the device with a wrist circumference suitable for this device.
• Do not repair or adjust the device yourself. In this case, perfect function is no longer ensured.
some button pressed.
Beurer BC 32 - Upper arm blood pressure monitor
Instructions for use
• Batteries can be life-threatening if swallowed. Therefore, keep batteries and products out of the reach of small children. If the
battery is swallowed, you must call for medical help immediately.
• Dispose of the device in accordance with the Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96 / EC. If you
have any questions, please contact the municipal disposal office.
• The blood pressure meter consists of precise and electronic components. The accuracy of the measured values and the service
life of the device depend on careful handling:
Slovensky
• Rest for about 5 minutes before each measurement!
The wrist blood pressure monitor is a non-invasive measure and control of the arterial blood pressure values of adults. With its
help, you can quickly and easily measure your blood pressure, save the measured values and have the course of the measured
values displayed. You will be warned if you have any heart rhythm problems.
• Remove the batteries if they are exhausted or if you will not be using the device for a long time. This will prevent damage that
could occur after they have leaked. Always replace all batteries at the same time.
• The measured values can only be used for your information, they do not replace a medical examination! Discuss your values
with your doctor, never derive your own medical decisions (eg medicines and their dosage)!
Sincerely, Your Beurer Team
2. Important instructions
• You can only use the blood pressure monitor with batteries. Note that data storage is only possible if your blood pressure monitor
is powered. Once the batteries are exhausted, the date and time of the blood pressure monitor will be lost. However, the stored
measurement values are retained. Automatic shutdown turns off the blood pressure meter to save battery power if it is not within
one minute
Battery instructions
- Do not drop the device.
Repair and disposal instructions
• Do not open the device. Failure to do so will void the warranty.
• Cardiovascular disease could cause erroneous measurements, even in very low blood pressure, circulatory and rhythm
disorders, and other previous conditions.
• Do not press the buttons unless the cuff is attached.
Storage and care instructions
• Always measure your blood pressure at the same time of day so that the values can be compared correctly.
Manual
• Batteries must not be charged or reactivated by other means, disassembled, thrown into a fire or shorted.
• Repairs may only be performed by customer service or authorized dealers. Before each complaint, first check the batteries
and replace them if necessary.
• Do not use different types, brands of batteries or batteries with different capacities. Preferably use alkaline batteries.
Dear customers, thank you for choosing our products. Our name is synonymous with high quality, thoroughly tested products
for use in the areas of energy consumption, body temperature, heart rate, gentle manual therapy, massage and air therapy.
Please read this manual carefully and keep it for future reference, make sure that it is available to other users and follow the
instructions.
• You should wait 5 minutes between two measurements!
- Protect the device against shocks, moisture, dirt, strong temperature fluctuations and direct sunlight.
Machine Translated by Google

5. "START / STOP" button
• Remove the battery compartment cover on the left side of the device.
7. Diastolic pressure
• The month starts flashing. Use the function key + to set the month 1 - 12 and confirm your entries with the function key "3"
Caution: You can only use the device with the original cuff.
Do not use rechargeable batteries.
• Confirm your selection with function key "3"
• Rest for about 5 minutes before each measurement! Otherwise deviations
may occur.
7. Display
9. Storage number
3. Description of the device
11. Determined pulse value
1. Battery replacement symbol
Warning: These marks can be found on batteries containing pollutants: Pb: Battery contains
lead, Cd: Battery contains cadmium, Hg: Battery contains mercury.
5. Blood pressure measurement
13. Day / night memory indication (A, P: AM, PM)
You should definitely set the date and time. Only then can you save your measurement values correctly with the date and time and recall them
later. The time is displayed in 24-hour format. To set the date and time, follow these steps:
Uncover your left wrist. Make sure that the blood supply to the hand is not limited by too narrow pieces of clothing. Place the cuff on the inside
of your wrist.
2. "MEM" save button
3. Systolic pressure
6. Wrist cuff
• The cuff must wrap tightly around the wrists, but must not choke it.
4. Adjustment button +
6. Symbol for users 1.2
Insert the battery
Indication on the display
10. Pulse symbol
• Then carefully close the battery compartment cover. If the battery replacement symbol appears, it is no longer possible to take
measurements, you must replace all batteries. Discharged batteries do not belong in the household waste. Dispose of them through your
electrical dealer or local collection point. You are required by law to do so.
• Press function key "3" for more than 5 seconds.
8. Time and date
• Insert two 1.5 V Micro batteries (alkaline type LR 03). Be sure to insert the batteries with the
correct polarity markings.
12. WHO classification
2. EE error symbol
Date and time setting
1. Battery compartment cover
• Set the day / hour / minute and always confirm your entry with the "3" function key.
Cuff attachment
""
Proper posture
• Switch on the blood pressure monitor with the "5" key.
• Connect the cuff with Velcro so that the upper edge of the device is placed about 1 cm below the palm.
• You can measure while sitting or lying down. Sit comfortably when measuring blood pressure. Wash your back and arms. Do not cross your
legs while sitting. The feet should touch the floor over the entire surface. You need to support your arm and bend it a little.
3. Function key ""
4. Heart rhythm disorder symbol 5. mmHg
unit
4. Preparation of measurements
Machine Translated by Google

save blood pressure measurements in the morning and evening.
Systola
Wait at least 5 minutes before measuring again!
If the systole and diastole values were in two different WHO ranges (eg systole in the "high normal" range and diastole in the "normal"
range), then the WHO graphic distribution on the instrument will always show a higher value, in the example described "high normal". ".
6. Save, recall and delete measurement values
Diastola
100-109
If there is more than 60 measurement data in the memory, the oldest data is currently deleted.
• Attach the cuff as described above and take the position in which you want to measure.
Heart rhythm disorders:
In any case, make sure that the cuff is at heart level. Otherwise, significant deviations may occur. Release your arm
and palms.
Repeat the measurement if the arrhythmia symbol appears on the display after the measurement. Make sure that you rest for 5
minutes before the measurement and do not talk or move during the measurement. If the arrhythmia symbol appears frequently, please
consult your doctor. Self-diagnosis and treatment based on measurement results can be dangerous.
• Then the cuff pressure is slowly read and recorded by the pulse.
Blood pressure range
Regular check-ups with a doctor
WHO classification:
See a doctor
Self control
Memory selection
• You can interrupt the measurement at any time by pressing.
Blood pressure measurement
90-99
85-89
80-84
<80
You have two memories, each with 60 memory locations, so that you can store the measurement results of 2 different people separately or
• The unit turns off automatically after 1 minute.
The bar graph on the display and the scales on the device show in which range the detected blood pressure is located.
• Use the "+" buttons to select user memory 1 or 2. Press the button to start the measurement. After checking the display, all digits are lit,
the cuff inflates automatically. The device detects values already during inflation, these values are used to estimate the pressure required
during inflation. If this pressure is not sufficient, the device will automatically inflate.
This device can identify possible heart rhythm disorders during the measurement and the symbol also warns of this after the
measurement. This may be a sign of an arrhythmia. An arrhythmia is a disease in which the heart rhythm is abnormal due to disorders in the
bioelectric system that control the heartbeats. Symptoms (missed or premature heartbeats, slower or too fast pulse) can be seen. infer from
heart disease, old age, physical dispositions, excessive eating, stress or lack of sleep. An arrhythmia can only be detected by your doctor.
(v mmHg)
Grade 3: severe hypertension> = 180 Grade
2: moderate hypertension Grade 1: mild
hypertension 140-159 High normal pressure
130-139 Normal pressure 120-129 Optimal
pressure <120 Source: WHO, 1999
Evaluation of results
(v mmHg)
Be sure to follow your doctor's instructions.
• After the measurement, the remaining air is released very quickly. Pulse, systolic and diastolic blood pressure appear on the display.
Measure
• In order not to skew the measurement results, it is important that you are calm and do not speak during the
measurement.
>=110
Regular check-ups with a doctor
160 –179
• The results are saved with the date and time after each successful measurement.
See a doctor
Self control
• Make your selection with the "MEM" key and then select the desired user memory with the "+" key. When the "MEM" key is pressed again,
the average value of all stored user memory measurements appears. After pressing the "MEM" button again, the average value of the last 7
days of the daily measurement will appear. (day: 5.00 - 9.00,
Switch on the blood pressure monitor with the button. select the desired memory location by pressing the "+" function key.
• The symbol E_ appears if the measurement could not be performed correctly. Observe the chapter Error message / rectification
in these operating instructions and repeat the measurement.
According to the guidelines / definitions of the World Health Organization (WHO) and the latest knowledge, the measurement results can be
classified and assessed according to the following table.
Machine Translated by Google

3. you have moved or talked during the measurement (Next to E3, the display also shows the heart rate symbol
• Carefully wipe the blood pressure computer with a slightly damp cloth.
• Do not place heavy objects on the device.
8. Cleaning and care
"
• Do not use any cleaning agents or solvents.
5. inflation takes longer than 25 seconds - E1.
If an error occurs, the error message E_ will appear on the display. Error messages may appear if:
2. the measured blood pressure value is extremely high or low - E3,
1. Inflation pressure exceeding 300 mmHg - E2;
In these cases, repeat the measurement. Make sure that the cuff hose is inserted correctly and that you do not move or talk.
Reinsert or replace the batteries if necessary.
9. Technical parameters
"),
• To change the user memory, observe the "Memory selection" chapter.
7. Error message / error correction
4. the cuff hose is not inserted correctly - E1,
• Under no circumstances should the device be washed under water, as this could allow liquid to enter and damage the device.
indication "A"). After pressing the "MEM" button again, the average value of the last 7 days of night measurement will appear. (night: 17.00 -
21.00, indication "P"). When the "MEM" memory key is pressed again, the last value of the individual measurements with date and time appears.
". (Na
www.borgy.cz
"
• To clear the memory, first press the "MEM" button, No. will appear on the display. 1. You can then select the user memory with the "+" key and
confirm your selection with the "MEM" key. Now simultaneously press the "+" buttons for 5 seconds and the display will show "CLA")
Measuring range
systolic 40 - 280 mmHg, diastolic 40 - 280 mmHg, pulse 40 - 199 beats / minute
storage temperature <85% relative humidity
Measurement
uncertainty Max. clinical trial standard deviation: systolic 8 mmHg / diastolic 8 mmHg
Pressure indication accuracy systolic ± 3 mmHg / diastolic ± 3 mmHg / pulse ± 5% of displayed value
Power supply 2 x 1.5 V Micro (alkaline type LR 03)
Application part type BF, Caution! Read the instructions for use!
BC 32
Permissible operating temperature +10 ° C to +40 ° C, <85% relative humidity
Measurement
method Oscillating, non-invasive measurement of blood pressure on the wrist
Weight
approximately 115 g
Permissible -20 ° C to +70 ° C,
Application part type BF
Cuff size For wrist circumference about 135 to 195 mm
Explanation of symbols
Model no.
Memory
2 x 60 data lines to store
Battery life for about 250 measurements
Accessories
Classification
Dimensions D69 x S66 x H31 mm
Storage case, instructions for use, 2 "AAA" batteries
Hluchov 1353
BORGY CZ, a.s.
250 01 Brandýs nad Labem-Stará Boleslav
Complaints / service
Tel.: [phone]
Email: [email protected]
Czech Republic
Exclusive importer and distributor for the Czech Republic and Slovakia:
• This device complies with the European standard EN60601-1-2 and is subject to special precautions regarding
electromagnetic compatibility. Be aware that portable and mobile RF communications devices can affect this
• EU RoHS device for medical devices 93/42 EC, the Medical Products Act and European standards EN1060-1 (Non-
invasive blood pressure meters, part 1: General requirements) and EN1060-3 (Non-invasive blood pressure meters, part 3:
Specific requirements for electromechanical systems for measuring blood pressure).
• If you use the device for commercial or financial purposes, you must carry out regular technical checks in accordance with
the "Medical Device Operator's Ordinance". Even for private use, we recommend that you have a measuring inspection
carried out by the manufacturer every two years.
device. You can request more detailed information at the customer service address below.
Machine Translated by Google