BGS technic 9246 User manual

BGS technic KG
Bandwirkerstr. 3
D-42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[e-mail]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
BGS 9246
Workshop Press | 20 t
FEATURE
1. Used for parts straightening, bending and pressing.
2. Multi-position bed for work height adjustment.
3. With air pump can reduce labor and improve working efficiency
WARNING
•This press is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a hydraulic press, do not use until
proper training and knowledge has been obtained.
•Do not operate this press beyond it rated capacity.
•DO NOT compress springs or other objects that could be ejected from the press. DO NOT
compress objects that could shatter.
•Please understand the max. working stroke before operate, Do not overload the max. working
stroke, so as not to damage parts.
•Check the press for loose or damaged parts before each operation. Replace damaged parts and
tighten all loose bolts before operating.
•Some parts being pressed may have a tendency to pop out of the press or explode under
pressure. Protect yourself accordingly.

BGS technic KG
Bandwirkerstr. 3
D-42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[e-mail]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
OPERATION
1. Place work piece on bed frame.
2. Locate and close release valve.
3. Pump handle until the ram nears work piece.
4. Apply load to work piece by pumping handle. Do not overload work piece.
5. Remove load from work piece by turning release valve. Stabilize work piece so it does not fall
while pressure is released.
6. Remove work piece after ram is fully retracted.
MAINTENANCE
•
Periodically, lightly oil all moving parts including the pump piston and hydraulic ram.
•
Check hydraulic connections and hoses before each use.
•
Do not use if cut, damaged, leaking or otherwise damaged connections and/or hoses are noted
DISASSEMBLE DRAWING
No.
Description
Qty.
1
Pressure gauge
1
2
Damping nut M16
8
3
Washer M16
16
4
Jack
1
5
Pole
2
6
Bolt M1
0×15
4
7
Washer M10
28
8
Pin
2
9
Tighter the scres
4
10
Damping nut M10
12
11
Connect board
1
12
Bolt M1
0×25
12
13
Leg
2
14
Handle
1
15
Pump
1
16
Adjust beam
1
17
Arbor plate
2
18
Limit circle
1
19
Limit ring
1
20
Cross beam
1
21
Bolt M1
6×40
8

BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[e-mail]
www.bgstechnic.com
EU-Konformitätserklärung
EC DECLARATION OF CONFORMITY
DÉCLARATION „CE“ DE CONFORMITE
DECLARATION DE CONFORMIDAD UE
Wir erklären in alleiniger Verantwortung, dass die Bauart der:
We declare that the following designated product:
Nous déclarons sous propre responsabilité que ce produit:
Declaramos bajo nuestra sola responsabilidad que este producto:
Werkstatt-Presse 20 to ( BGS Art. 9246 )
Hydraulic Shop Press
Presse d’atelier
Prensa de taller
folgenden einschlägigen Bestimmungen entspricht:
complies with the requirements of the:
est en conformité avec les réglementations ci-dessous:
esta conforme a las normas:
Machinery Directive 2006/42/EC
Angewandte Normen:
Identification of regulations/standards:
Norme appliquée:
Normas aplicadas:
EN ISO 12100-1:2003
EN ISO 12100-2:2003
EN 1494:2000
Certification No. : GB/1067/1528/09 / ZD07202
Reference: CE2009WF119/9
Wermelskirchen, den 24.01.2014
ppa.
Frank Schottke, Prokurist
BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen