BH FITNESS H915A User manual

H915A
OWNER’S MANUAL
H915A

2

3

4
Assembly
STEP 1
Attach the front (16) and rear feet (12) to the
frame using the nuts (8), washer (9) and bolts
(10).

5
Step 2
The handlebar post already set up when you
received. Attach the handlebar post inserting
into the head tube of the frame. Adjust the
height and then securely tighten the knob (44) in
proper position. Adjust the angle of handlebar
(21) and then securely tighten the screw (52)
Step 3
Insert the seat tower (17) into the frame’s seat
tube, adjust the height and then fix in position
with knob. Insert the seat slider (18) into the
seat tower and fix using the knob (19) (19-1).
Attach the saddle (1) into seat slider, make sure
the saddle clamp screw be securely tightened.
Step 4
Attach the pedals (11) into the crank arms(7), each pedal
is marked with the L (left) or R (right) to denote the side
of the spinning bike they are on, Note- the right hand
crank is on the same side as the chain guard (24). Be
careful to align the threads correctly to avoid any
damage. A little grease on the threads should help the
pedals to screw in easily and correctly, tighten using a
15mm spanner; both pedals threads should tighten
towards the front of the spinning bike. Attach the cage
(29) on the frame by screw (30) & washer (30-1).
Insert console (37) into clamp on the handlebar bar.

6
MOVING
There are moving wheel (13)
located in front of foot tube for
easy to moving the machine.
Step 5
To adjust the exercising resistance on the complete
spinning bike by the brake knob (42) of brake system,
and then simply loosen (-) or tighten (+).
The flywheel should rotate freely without resistance
when you loosen (-) the brake system totally.
More experienced riders may wish to increase the
overall resistance by tighten (+) the brake system
totally.

7
Instruction ;
Handlebar and seat adjustment. It is important that the
handlebar and seat are set at the correct height for
your body. Ask your instructor for assistance.
Adjusting the handlebar height-Undo the knob that is
located where the stem fits into the frame. Slide the
handlebar/stem up or down to the required height
and retighten the knob. Make sure it is securely
tightened and that there is no lateral or vertical
movement of the handlebar.
Pay attention on ” MIN INSERT” mark for safety
adjustment.
Adjusting the seat height-undo the knob
located where the seat tower fits into the
frame. Adjust the seat tower to the required
height. Then retighten the knob. Make sure
it is tight enough to prevent the seat from
twisting side to side. The seat position can be
adjusted forwards and backwards. Undo the
knob located directly below the seat slider.
Loosen the knob then slide the seat to the
required position. Then make sure the knob
retighten.
Seat :
Make sure tighten enough for
both side of nut after adjust
the seat position. To
prevent the seat from twisting
side to side.

8
Exploded Drawing

9
Part list
No. Name Unit No. Name Unit
1 Saddle PC 31 Handlebar stem end cap PC
2 Seat slider PC 32 Crank bolt PC
3 Seat tower rubber cap PC 33 Flywheel security nut PC
4 Seat tower rubber cap PC 35 cover for flywheel w/bolt PC
5,7 Crank arm set SET 36 flywheel adjuster bolt PC
6 Chain PC 37 Console SET
8 Foot tube nut PC
9 Foot tube washer PC 38 elbow pad w/holder, bolt PC
10 Foot tube bolt PC 39 Flywheel SET
11 Pedal PR 40 Screw & nut for brake pad PC
12 Rear foot tube (complete) SET 41 Brake pad w/holder PC
13 Front end cap PR 42 Brake system PC
14+15 Rear end cap PR 43 Rubber cap for seat post PC
16 Front foot tube (complete) SET 44 Knob
SET
17 Seat tower w/rubber cap PC 45 Knob washer
19 Seat extender knob PC 46 Alloy blind clip (R )
19-1 Seat extender knob 47 Knob spring
20 Handlebar end plug (pc) PC 48 Alloy blind clip (L )
21 Handlebar PC 49 Knob plastic washer
22 Screw for spring plate PC 50 Knob fixed bolt
23 Spring plate PC 51 Knob washer PC
24 Outer chain guard PC 52 handlebar stem bolt PC
24-1 Inner chain guard PC 53 Fixed bracket for console PC
25 Flywheel axle
SET
26 Fixed wheel
27 Flywheel bearing
34 Flywheel security washer
28 Axle set SET
29 Bottle cage PC
30 Screw for bottle cage PC
30-1 Washer for bottle cage PC 90 Sensor and cable

10
Maintenance Chart
No DESCRIPTION Daily Weekly Monthly Quarterly Annually
1
Keep machine clean: Wipe machine
down with clean & dry fabric to clear
dirt & sweat.
X
2
Spray with WD40 or similar on the
seat post set, handlebar set (Don’t
spray on the main frame)
X
3 Visual check X
4 Check security of handle bar post &
seat post X
5 Check security of saddle X
6 Remove handlebar post and clean
tube X
7 Remove seat and clean tube X
8 Check brake pads for wear-align X
9 Check brake adjustment X
10 Check security of all knobs & release
lever X
11 Check toe straps for signs of wear X
12 Check crank bolts and re-tighten X
13 Make sure pedals are screwed in X
14 Check chain tension X
15 Wipe the anti-rust oil on the
flywheel X
16 Check bottom bracket X
17 Check flywheel bearings X
18 Full service-frame inspection X