BH FITNESS BT6443 T200 User manual

BH Treadmill
BT6443 T200
OWNER'S MANUAL
Version 1.00

BT6443/T200 Treadmill
- 1 -
INDEX
SAFETY PRECAUTIONS.........................................- 2 -
SAFETY USE ATTENTION ......................................- 2 -
GROUNDING WIRES INSTRUCTION...................- 3 -
ASSEMBLY INSTRUCTION ....................................- 4 -
FOLDING INSTRUCTION........................................- 6 -
GETTING START ......................................................- 7 -
WARM-UP EXERICSE .............................................- 8 -
OPERATION INSTRUCTION ..................................- 9 -

BT6443/T200 Treadmill
- 2 -
SAFETY PRECAUTIONS
Warning:
In order to avoid the accident, you have to pay attention to the following:
When using the treadmill ,keep attaching the safety key clip to your clothes or belt;
When you are exercising, PLS swing your arms naturally, straight ahead. Don’t look at your feet;
Pls accelerate the speed gradually, adapt to the current speed before the acceleration ;
When run into emergency , press the emergency stop button or pull away the safety key;
When the treadmill was completely stopped leave is allowed.
Attention:
Strictly according to the assembly instruction to install this product.
A. Before starting any exercise program, consult your physician.
B. Make sure all the bolts locked tightly.
C. Do not place the treadmill at the moist places, it may cause trouble.
(We take no responsibility for any troubles or hurts due to above reasons)
D. Wearing sports suits and shoes before you start exercise.
E. Do not exercise in 40 minutes after meal.
F. Do warm-up exercise to avoid injury.
G. People who suffering from hypertension should consult doctor before start the exercise.
H. This treadmill only used for adults.
I. The elderly, the disabled, children should be given proper care and guidance.
J. Do not plug anything into any parts of this fitness equipment, or it may damage.
SAFETY USE ATTENTION
Only the treadmill had finished the installation and put on the motor protect cover, you can plug
in the power. The power line plug into the power socket which should with the safety grounding
line, we suggest fit on overload protector to ensure the safety of the user and the treadmill.
（1）PLS position the treadmill on a clear, lever surface. Do not place it on thick carpet as it
may interfere with proper ventilation under the treadmill. Also do not place the treadmill near
water or outdoor,guard against damp. if it is broken, please purchase it from distributor or
connect our company directly.
（2）Place the treadmill at the place where is convenient for plug in the power, do not ward off
the socket on the wall.
（3）Never start the treadmill while you are standing on the running belt. After turning the
power on and adjusting the speed control, there maybe a pause before the running belt
begins to move, always stand on the plastic checkered plate of the treadmill both sides till
the belt moving.
（4）Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose fitting
clothing that could become caught in the treadmill. Always wear running or aerobic shoes
with rubber soles.
（5）Never remove the protective cover casually, if need to open, PLS be sure to unplug the
power line.
（6）Keep the kids away from the treadmill during operation.

BT6443/T200 Treadmill
- 3 -
（7）Always hold the handrails when initially walking or running on the treadmill until you are
comfortable with the speed.
（8）The treadmill is indoor equipment do not use outdoor. Don’t refit the treadmill. The
treadmill made by special equipment. Pls do not remodel or do others.
（9）Child use the treadmill must have adult on side.
If the treadmill suddenly increased in speed due to an electronic failure or the speed being
inadvertently increase, the treadmill will come to a sudden stop when the safety key is
disengaged from console.
（10）Maximum user weight is 100 KG.
GROUNDING WIRES INSTRUCTION
The products must be grounded first. If malfunction or breakdown occurs, grounding will provide
a path of least resistance for electric current to reduce the risk of electric shock.
The product is equipped with a cord having an equipment-grounding conductor and a grounding
plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER –
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the products
are properly grounded. Do not modify the plug provided with the product – if it will not fit the
outlet, have a proper outlet install by a qualified electrician.
The product is for use on nominal 220V-240V and has a grounding plug that looks like the plug
illustrated in the figure. Make sure that the product is connected to an outlet having the same
configuration as the plug.
There is no need to use any adapter for this product.
Figure
Grounding methods

BT6443/T200 Treadmill
- 4 -
ASSEMBLY INSTRUCTION
When you open the carton, you will find the below spare parts.
1.5#Wrench
2.6#Wrench
3.Wrench
4L/R.Front Cover
5.Treadmill（Folded）6.Safety lock 7.Bolt
M8*20 6pcs
8. Washer
∮
8.4*
∮
14.5*t0.8 10pcs
9.Bolt M4*8 4pcs 10. Silicone Oil 11.MP3 Line 12.Bolt M8*35 4pcs
Install
Step 1.
Straight the upright (13L/R)
according to the direction of
the arrow,like the draw.
13R
13L
5
12
8
12
8
13L
13R
78
7
8
Step 2.
Secure the upright(13L/R) tightly
with thw bolt(7) M8*20 and the
washer(8)Ø8.4*Ø14.5*t0.8.

BT6443/T200 Treadmill
- 5 -
ATTENTION: Confirm complete assembly as required above ,then lock
all bolts. Checking everything is OK before power on. About the treadmill
operation and using, PLS read the following instruction carefully .
7
8
13L
13R
7
8
Step 3.
Secure the computer tightly onto the
upright(13L/R) with the bolt(7)
M8*20 and the
washer(8)Ø8.4*Ø14.5*t0.8.
4R
9
11
6
4L
9
Step 4.
Install the front cover onto the
upright(13L/R) with the bolt(9) M4*8
Then put the safety lock (6)and
MP3 Line onto the right place
according to the diragram.

BT6443/T200 Treadmill
- 6 -
FOLDING INSTRUCTION
Support the end of the treadmill
with hand, then pull it up towards
the arrow direction, untill hearing
the sound”ka” that the cylinder is
locked into the round tube.
Support the end of treadmill
with hand , kick the place
as arrow showing of air
pressure bar, then the base
frame will fall down automatically.

BT6443/T200 Treadmill
- 7 -
GETTING START
PREPARE：
If you are around 45 years old, or have health problem, or this is your first time to do exercise,
please consult doctor or professional before use it.入门指南
Before use the motorized treadmill, please stand on the side to learn the operation, such as start,
stop and speed adjustment. Then stand on the plastic checkered plate of the treadmill both
sides , catch the handrail with both hands, turn on the treadmill by 1.6—3.2km/h low speed,
stand straight, look forward, try to run on the running belt few times with one foot, then stand
on the running belt to do exercise. After adapting, you can adjust the speed to 3—5km/h and
keep doing about 10 minutes, then stop slowly.
EXERCISE：
PLS stand on the side to learn how to operate, such as adjust speed or incline, start do the
exercise until you are familiar with it.
Walk 1 km by constant step need about 15-25 minutes, please record the time. Walk 1km by
4.8km/h need about 12minutes, if you can do it easily by few times, then can adjust to the high
speed and incline, and go on to do it 30 minutes, you can take a good exercise. Before do walk
exercise, please remember it is for your health and can not irritable.
EXERCISE FREQUENCY
Target is 3--5 times per week, do 15-60mins each time. It is better to make a time schedule first,
do not do the exercise accord to your favor. You can control the movement acuteness degree
through adjust speed and incline. We suggest you do not set incline when start do exercise. You
can increase the incline when you want to add the movement acuteness degree
AMOUNT OF EXERCISE：
SHORTCUT----The best way to save time is do 15-20 minutes exercise.
Warm up 2 minutes by 4.8 km/h, and adjust the speed to 5.3 km/h and 5.8 km/h, continue do
exercise by this two speeds. Then add 0.3 km/h per 2mins speed increase, until you feel
breathing quickened but not difficulty breathing. Keep this speed to do exercise, if feels
uncomfortable, please reduce 0.3 km/h. Leave 4 minutes to reduce speed at last. If you feel it is
hard to strengthen the movement intensity by increase speed, then you can choose the way of
increase incline slowly, it also can strengthen the movement intensity.
CONSUMPTION OF HEAT----This way can really consumption the heat.
Warm up 5 minutes by 4--4.8 km/h speed, then add 0.3 km/h per 2 minutes increasing speed,
you can do 45mins on this speed that you will feel it is comfortable and challenge. In order to
strengthen do exercise. You can do 1 hour by this speed and add 0.3 km/h speed when you
heard some business advertisements, and return the speed back when go to next program, so at
this period, the heat will be consumed enough. At last keep 4 minutes to reduce the speed.
CLOTHING：
All you need is a pair of fully stretch shoes, at the same time sole don’t stick foreign matters
avoid damage running deck and belt. Please wear comfortable suitable for sports clothes.

BT6443/T200 Treadmill
- 8 -
WARM-UP EXERICSE
It is better to do some warm-up exercise. Warm the muscle easy stretch, so use 5-10
minutes to warm-up. Then stop and according below method to do stretch exercise for five
times, and each foot do 10 seconds or more every time. After running, do those stretch
exercises one more time.
1. Reach Down Knees slightly bent and body slowly bent
forward, back and shoulders relax, trying to touch toes.
Keep 10-15 seconds, and relax. Repeat 3 times (See
picture l).
2. Hamstrings Stretches Sitting on a clean cushion, put
one leg straight, the other inward and close to the inside of
the straight leg. Try to touch your toes by hand. Keeping
10-15 seconds, and relax. Repeat 3 times for each leg
(See picture 2).
3. Crus and Feet Tendon Stretches Standing with two
hands on the wall or tree, one leg behind. Keeping your
legs straight and the heel on the ground, tilt to the wall or
tree. Keep 10-15 seconds, and relax. Repeat 3 times for
each leg (See picture 3).
4. Quadriceps Stretches Keeping your balance with your
left hand holding on the wall or table, then stretch your right
heel toward your buttocks slowly, until you feel very tense
in the front of your thigh. Keep10-15 seconds, and relax.
Repeat 3 times for each leg (See picture 4).
5. Sartorius (Inner Muscles of the Thigh) Muscle Stretches
Sitting down with your soles opposite and knees outward.
Pull feet toward groin Keep 10-15 seconds, and relax.
Repeat 3 times (See picture 5).

BT6443/T200 Treadmill
- 9 -
OPERATION INSTRUCTION
1、LCD DISPLAY
A. SPEED WINDOW：
In setstate, display “P01,P02-------P12-U1-U2-U3-FAT”;In running, display the speed date; the speed
display range :1.0-14.0KM/H.
B. TIME WINDOW：
Display the time, when it in manual mode ,is the timing from 0:00-99.:59,when time to 99:59,treadmill
speed smooth slow down to stop and the speed window display”End”,5second full stop into standby
mode; Distance, clorie mode ,is the timing from 0:00-99:59,when time to 99:59 reset and keep on
timing; count down mode the timing from seting time to zero. when count down to 0:00, treadmill
speed smooth slow down to stop and the speed window display”End”,5second full stop into standby
mode.
C. DISTANCE/INCLINE WINDOW：
Display the distance, forward count from 0.00-99.0,when count to 99.0 reset and keep on
count ;backward forward count from setting to 0.0, when count down to 0:00, treadmill speed smooth
slow down to stop and the speed window display”End”,5second full stop into standby mode.
D. CALORIE WINDOW：
Display the calorie of the sporter. forward count from 0.00-999.0,when count to 999.0 reset and keep
on count ;backward forward count from setting to 0.0, when count down to 0:00, treadmill speed
smooth slow down to stop and the speed window display”End”,5second full stop into standby mode.

BT6443/T200 Treadmill
- 10 -
E. INCL/PUL. WINDOW：
Display the calorie and the current incline data, incline display range:0-12,when sporter grasp the hand
pulse with both hand,the system can auto detect the sporter ‘s heartrate and display .the heartrate
display range :50-200 times/min,this date is for reference only,not as a medical data.
2、BUTTONS：
‘STRAT’；‘STOP’；‘PROGRAM’；’MODE’；’SPEED+’；’SPEED-’；’INCLINE+’；’INCLINE-‘ ；
Speed shortcuts:3,6,9,10,12KM/H; Incline shortcuts:3,6,9,10,12.
3、BUTTONS FUNCTION EXPLAIN：
A. ‘PROGRAM’ button：
In standby condition, Press the button can cycle select the program: manual
program-P01-P02…-P99-U01-U02-U03 -FAT
B. ‘MODE’ button：
In standby condition ，Press the button can cycle select the mode：manual program(normal
mode)—time countdown—distance countdown—calories countdown；In the ‘FAT’ program，the function
of the mode button reference to the body fat test function.
C. ‘START’ BUTTON：
Press the button to start the motor.
D. STOP’BUTTON：
Press the button to stop the motor.
E. SPEED+BUTTON：
In the set state，press the button can increase the set data. under the operating state, press the button
can add the speed.
F. SPEED- BUTTON：
In the set state，press the button can decrease the set data. under the operating state, press the button
can cut down the speed.
G. ‘INCLINE+’ button：
In the setting state，press the button can increase the set data. under the operating state, press the
button you can add the incline.
H. INCLINE：
In the setting state，press the button can decrease the set date. under the operating state, press the
button you can countdown the incline.

BT6443/T200 Treadmill
- 11 -
I. Speed shortcuts：
3、6、9、12KM/H，under the operating state，press the button adjust the speed to the set value.
J. Incline shortcuts：
3、6、9、12 sections，under the operating state，press the button adjust the incline to the set value.
FIX PROGRAM/STARTING：
1. PROGRAM EXPLAIN：
A. One manual program,This program includes：
Normal mode(default)，time countdown、calories countdown、distance countdown.
B. 12 fixed program：P01，P02，…，P12.
C. User setting program：U01，U02，U03.
D. One body fat test function.
2. Starting explain：
A. Put the safety lock on the right place of the panel.
B. Press the ‘START’ button ,the windows show3-2-1,each time with a alarm noise, then the motor
started.
Manual programming operation：
1. Enter manual program：
A. Turn on the power switch, go into normal mode of manual program directly
B. When stop status, press ‘mode ’button can select go into normal mode of manual program
2. Three set function of manual program：
Time setting, Distance Setting, Calorie setting
A. When go into manual program, the time window display 0:00;
B. In manual program, press ’mode’ button go into time countdown mode, the time window display time
and flicker, initial time :15:00;press’speed+’,’speed-‘button can set countdown. the setting
range :5:00-99:00
C. In time countdown mode, press ’mode’ button go into distance counter down mode, initial distance
display:1.0km, press ’speed+’ ,’speed-‘button can set distance. the setting range :0.5-999km,Every
time to increase or decrease of 0.1km.

BT6443/T200 Treadmill
- 12 -
3．Manual programming operation：
A. Press the “START” button，3 seconds countdown, then the treadmill start with the speed1.0km/h ；
B. Press SPEED+/SPEED-to adjust the speed；
C. Press INCLINE+/INCLINE- to adjust the incline；
D. Press the speed shortcut button to the setting speed value；
E. Press the incline shortcut button to the setting incline value；
F. The treadmill is running ,press the “STOP” button, the motor stop working；
G. Take away the safety lock and the treadmill will stop quickly with noise BI-BI-BI，LCD window
display“---or----”.
H. When the set time/set calories/ set distance countdown to 0,the alarming make a short noise
Bi-Bi-Bi，and the speed gradually reduce to stop ，when the alarming make the long noise Bi-Bi-Bi
the speed window display “End”，5 seconds later, the treadmill back to the standby state，the
alarming make a noise Bi-Bi；
I. The unset parameters will add up .When reach the max data automatic back to 0 and going on.；
under the manual mode, the treadmill stop running when the time reach99:59(100minutes) .
Fixed PROGRAM MODE：
At standby state, press’ prog’ button, select the internal fixed program mode”P01-P12)
1. Initial setting time 10 minutes，time set only，range：5:00—99:00. Press the SPEED+/SPEED- to adjust
the time value；
2. Press the START button, the motor going to operate, and the speed increase to the setting value in the
first PROG (See the PROGRAM EXERCISE CHAT)；
3. Press SPEED+/SPEED- to adjust the speed；
4. Press INCLINE+/INCLINE- to adjust the incline ；
5. Press the speed shortcut button to select the speed；
6. Press the incline shortcut button to select the incline；
7. Each program is divided into 10 sections ,the operation time of each section is one-tenth of the set
running time；
8. At the transition between the sections ,the alarm will make three noise；
9. When the time countdown to zero the alarm make short sound Bi-Bi-Bi，The speed gradually reduce to
0，the alarm make long noise Bi--Bi—Bi and the speed window display “End”，5 seconds later, the
treadmill back to standby situation with the alarm make long sound Bi--Bi；
10. Take away the safety lock the treadmill will stop quickly ,and the window display “---or----”alarm make
the noise Bi-Bi-Bi；

BT6443/T200 Treadmill
- 13 -
FIXED PROGRAM MODE DATA：
time
program
SETTING TIME/ 20 = EVERY GARDE TIME
1 2 3 4 5 6 7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
P0
1
SPEED
2 4 3 4 3 5 4 2 5 2 6 2 7 2 8 3 7 3 9 3
INCLIN
E
1 2 3 3 1 2 2 3 2 5 4 5 6 6 4 5 5 6 5 2
P0
2
SPEED
2 5 4 6 4 6 4 2 4 3 3 6 5 7 5 7 5 3 5 2
INCLIN
E
1 2 3 3 2 2 3 4 2 3 2 3 4 4 3 3 4 5 3 2
P0
3
SPEED 2 5 4 5 4 5 4 2 3 3 3 6 5 6 5 6 5 3 4 2
INCLIN
E
1 2 2 3 1 2 2 2 2 2 2 3 3 4 2 3 3 3 3 1
P0
4
SPEED 2 6 7 4 4 7 4 2 4 3 3 7 8 5 5 8 5 3 5 2
INCLIN
E
4 5 6 6 9 9 1 12 6 4 5 6 7 7 10 10 2 12 7 3
P0
5
SPEED
2 4 6 8 7 8 6 2 3 3 3 5 7 9 8 9 7 3 4 2
INCLIN
E
3 5 4 4 3 4 4 3 3 3 4 6 5 5 4 5 5 4 4 2
P0
6
SPEED
2 4 5 5 6 5 6 3 3 3 3 5 6 6 7 6 7 4 4 2
INCLIN
E
3 5 3 4 2 3 4 2 3 3 4 6 4 5 3 4 5 3 4 2
P0
7
SPEED
3 6 7 5 8 5 9 6 4 2 4 7 8 6 9 6 10 7 4 3
INCLIN
E
2 2 3 3 2 2 4 6 2 3 3 3 4 4 3 3 5 7 3 2
P0
8
SPEED
3 6 7 5 8 6 7 6 4 4 4 7 8 6 9 7 8 7 5 3
INCLIN
E
1 2 4 3 2 2 4 5 2 2 2 3 5 4 3 3 5 6 3 1
P0
9
SPEED
2 8 6 4 5 9 7 5 4 4 3 9 7 5 6 10 8 6 5 3
INCLIN
E
2 2 6 2 3 4 2 2 2 2 3 3 7 3 4 5 3 3 3 1
P1
0
SPEED 2 3 5 3 3 5 3 6 3 4 3 4 6 4 4 6 4 7 4 3
INCLIN
E
4 4 3 6 7 8 8 6 3 4 5 5 4 7 8 9 9 7 4 3
P1
1
SPEED 2 5 8 10 6 9 5 3 2 3 3 6 9 10 7 10 6 4 3 2
INCLIN
E
1 3 5 8 1 7 6 3 2 4 2 4 6 9 2 8 7 4 3 3
P1
2
SPEED
2 5 5 4 4 6 4 2 3 5 3 6 6 5 5 7 5 3 4 4
INCLIN
E
3 5 6 7 12 9 11 11 6 4 4 6 7 8 12 10 11 11 7 3

BT6443/T200 Treadmill
- 14 -
USER PROGRAM：
Treadmill have three user program can setting by the user except the P1-P12 Fixed program:U1,U2,U3
1. The setting of the user program
At the standby state, press the ‘PROGRAM’ button to select the’ U1’,’U2’,’U3’, and word ’USER” display.
press ‘mode’ button enter program parameters,then can set the first period . press the
‘SPEED+’,’SPEED-’ to set the speed, press the ‘INCLINE+’,’INCLINE-’ to set the incline ,press the
‘MODE’ button to finish the settings of the first period and enter the second. Set up like this untill you
finished the 20 period. The setup parameters will keep forever untill you reset them . And the data
would not lost because of the lost of power.
2. The start of the users
At the standby state, Continue press the ‘PROGRAM’ button until the ‘U01’,’U02’,’U03’, and finished
the setup. Press the ‘START’ button to start the treadmill. The treadmill will running as the setup
program.
3. Introduction of the users setup
Each user divide the time into 120 period, Must finished the set up of the time ,the speed and the
incline in the 10 period that you can start the treadmill.
BODY FAT TEST：
1. At the stop state ,press’prog’button to select the ‘FAT’(body fat test mode)
2. Press ‘mode’button enter body fat test , set the parameter (F-1--sex，F-2—age，F-3—height，
F-4—weight，F-5-physical testing),Then press the ‘ SPEED+/_’ button can ajust the setting
value(F-1---F-4);F-5 display”——“,get into the set of the set the parameter(F-1--sex，F-2—age，
F-3—height，) . All parameter is setting well,then Press the ‘MODE’ button again ,Upon grasp the
hand pulse with both hands for 5-6 seconds the heart rate window will display your body mass
index(BMI).
3. Enter in to body fat test function,first display window display “F-1”, F-1—sex;setting window display
01;,press “speed+/-“ button to adjust the data, 01-male 01(male),02(female)
4. Press the “MODE” button to the next turn, entering “F-2”,F-2—age; setting window display
25(years),press “speed+/-“ button to adjust the data.the age range :10-99(years)
5. Press the “MODE” button again, entering “F-3”,F-3—height，setting window display 170(cm);press
“speed+/-“ button to adjust the data.the height range :100-200cm
6. Press the “MODE” button again, entering “F-4”,F-4—weight，setting window display 70(kgs);press
“speed+/-“ button to adjust the data.the weight range:20-150kgs
7. Press the “MODE” button again,entering”F-5”, when the speed window display “---” you have enter into
the body fat test procedure . Grasp the hand pulse with both hand ，the setting window will display the
body fat data with 8 second.
8. Base Asian standard . Ideal FAT should be between 20 to 25,if less than 19 means too thin,if between
25 and 29 is overweight,if beyond 30 are considered obese(The data is just for reference, can not
be a medicial data)

BT6443/T200 Treadmill
- 15 -
F-1 sex 01-male 02-female
F-2
age
10-99
F-3
height
100-200
F-4
weight
20-150
F-5 BMI
≤=<19
thin
=(20---25)
normal
=(25---29)
overweight
≥>=30
obesity
Running parameter display and setting range：
Default
value
Setting default
value
Setting Range Display Range
TIME(M:S)
0:00 15:00 5:00-99:00 0:00-99:59
SPEED(KM/H)
0.0 N/A N/A 1.0－14.0
INCLINE
（SECTIONS
）
0 N/A N/A 0－12
DISTANCE(KM)
0.0 5.00 0.50－99.90 0.00－99.99
CALORIES(KCL)
0 100.0 10.0－999.0 0.0－999
Safety lock function：
The window shows “SAFE” when take away the safety lock and the treadmill will stop quickly with the
short sound Bi-Bi-Bi. and all the button useless.
Power saving mode：
When treadmill stops and no actions for more than 10 minutes, the system will shut down the display and
going into POWER SAVING state. Press any key to wake it up.
MP3 Player Function(customized) ：
When turn on the power, connect the MP3 player or other audio equipment, the computer will play the
music you can adjust the sound size by the button on the audio equipment. PLS not too loud that will
affect the quality of the sound and the inside audio.
Shutdown：
You can turn off the power to shutdown the treadmill at any state. That this will not damage the treadmill

BT6443/T200 Treadmill
- 16 -
Attention：
1. Check the power and safety lock is sure a valid state before start do exercise.
2. When run into emergency, pull off the safety lock to stop the treadmill quickly；， and put on the safety
lock, the system back to default, waiting for input the instruction.
3. If there is any problem，PLS contact the distributor .Amateurs, do not attempt to disassemble or
maintain so as to avoid the damage of equipment
Simple troubleshooting methods：
Fault Description Possible Reason Check Method Fault Processing
Power on , no
reaction in the
computer
1.power plug get loose
1.check the plug and make
sure the wire connect well
1.con
nect the wire again
2.power switch not open 2.check the switch
2.turn on the power again
The Motor Doesn’t
Work
1.Motor circuit abnormal
1.check the motor circuit, if
they are correct plug and
plug well
1.Replug the motor line
2. Not press the “START”
button
2.check the “START” button,
it may useless or not press
2.repress the button
3.the safety lock may lose or
dropped
3.check safety lock
3.place the safety lock
4.The motor plug loose or
damaged
4.test the motor
4.change the motor
5.The specification of the
power or the controller not
correct AC
（
110/230
）
V
5.make sure the
specification
Choose the correct
specification
The Motor and
Other Parts is ok,
but the Treadmill
doesn’t running
SENSOR induction bad
1.check the distance from
the magnet and the sensor
position
1.adjustment the distance in
5mm to the magnet
2.the wires may damaged or
not connect well
2.change the wires or sensor
3.the joints may not connect
well
3.connecting the joints again
The Display
Content not clear
PA circuit board screw not
clock well or the connector
not connect well
Check the circuit make it
connect well
Reset the connector and
lock the screw tightness
No pulse data
display
1.SENSOR induction
bad
1.check the wires’
connection
1.connect again or change
2.check the joints
2.connect again
2.human induction not
sensitive
（
ear clip
）
3.Knead the earlobe several
times.
Retest
3.human induction bad(hand
pulse
）
4.wetting hands or do some
friction.
Retest
E01(fault code)
the computer and the
controller Communication
abnormal
1.check the connection line
between the computer and
the controller
1.change the line
check the joints
2.connecting the joints
again

BT6443/T200 Treadmill
- 17 -
E02(fault code) Explosion-proof protection
1.the power and voltage is
less than 50% normal
1.use the r
ight power and
voltage
2.check the connection of
the motor or the motor may
damaged
2.connecting again
or
change the motor
3.check there is special
smell of the controller or not
3.exchange the controller
E03(fault code)
1.failure to detect the motor
signal for 15 seconds or
above
2.failure to detect the sensor
signal for 10 seconds
1. check the installation of
the sensor and the magnet.
1.correct install the sensor
and the magnet
2.check the connection of
the sensor
2.reconnection
3.check the sensor if it is
damaged
3.chang the sensor
E04(fault code) Failure study for the incline
motor
1.check the connection of
the VR line
1.reconnecting the joint of
the VR line
2.check the connection of
the AC line
2.reconnecting the joint of
the AC lin
e
3.check the connection of
the motor line
3.reconnecting or change
the wires
4.check the motor if it is
damaged
4.change the motor
5.failure study
5.press the button on the
controller for3
second ,restudy again
E05(fault code) Over-current
1.mak
e sure the power and voltage is comply with
standard
2.change the motor or controller, test again
E08(fault code)
EEPROM(data memory
error)
1. the part 24C02is broken or not connected 24C02 well.
2. change them immediately.

BT6443/T200 Treadmill
- 18 -
SAFETY EXERCISE
Please consult professional staff before do exercise. He can help recommendation exercise
rate/intension and time according to your age and health condition. When running, if you feel
chest tightness or chest pain, irregular Heartbeats, short of breath, dizziness or other unwell,
please stop immediately! And consult professional before you want continually to do exercise. If
you often use treadmill, you can choose normal walk speed or jog speed.
If you have no experience or can't make sure the best testing speed, you can reference below
standard:
Speed 1-3.0 km/h weak constitution people.
Speed 3.0-4.5 km/h sedentary or not often exercise people.
Speed 4.5-6.0 km/h walking quickly people.
Speed 6.0-7.5 km/h fast walk people.
Speed 7.5-9.0 km /h jogger.
Speed 9.0-12.0 km/h intermediate speed runner.
Speed 12.0-14.5 km/h experienced runner
Speed14.5-18.0 km/h excellent runner.
ATTENTION
It is suitable for walker to choose less than or equal to 6 km/h speed.
It is suitable for runner to choose more than or equal to 8.0 km/h speed.

BT6443/T200 Treadmill
- 19 -
MAINTENANCE INSTRUCTION
WARNING
Please make sure pulled out the treadmill's power plug before cleaning or maintain the product.
Always unplug the treadmill from the electrical outlet before removing the motor cover. At least
once a year remove the motor cover and vacuum under the motor cover.
CLEANING
General cleaning the unit will greatly prolong the treadmill working life.
Keep treadmill clean by dusting regularly. Be sure to clean the exposed part on both side of the
walking belt and also the side rails. Make sure the shoes are clean ,This reduces the build up of
foreign material underneath the running belt. The top of the belt need cleaned with a wet, soapy
cloth. Be careful to keep liquid away from the electrical components and underneath the running
belt.
This treadmill's running belt and deck are equipped with a pre-lubricated, low maintenance deck
system. The belt/ deck friction may play a major role in the function and life of your treadmill,
thus requiring periodic lubrication. We recommend a periodic inspection of the deck.
We recommend lubrication of the deck according to the following timetable
Light user (less than 3 hours/ week) annually
Medium user (3-5 hours/ week) every six months
Heavy user (more than 5 hours/ week) every three months
We suggest you buy lubricating oil from local distributors or contact our company directly.
1. In order to maintain and prolong the working life of your treadmill, we suggest you power off for 10
minutes after every 2 hours’ running.
2. The loose running belt will lead slip when you are running; the tighten running belt will affect the
performance of the motor, also can add the wear of the rollers. The perfect condition is the belt can
be lift from the running deck about 50-75mm