Billy Goat MV600SPE User manual

Part No 840245 1 Form No F060711D
BILLY GOAT ®MV650SPH and MV600SPE
Self-Propelled Vacuum Owner’s Manual
Accessories
Caster Kit Hose Kit Bag Liner Kit Felt Bag Kit
Use on hard surface
for maneuverability.
For vacuuming hard
to reach areas. To collect leaves,
thatch, and grass. Use on all dusty conditions.
P/N 840129 P/N 840116 P/N 840134 P/N 840194

Part No 840245 2 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
CONTENTS
Specifications and Sound/Vibration ................................................................................................................... 3
Instruction Labels ............................................................................................................................................... 4
Assembly Instructions ........................................................................................................................................ 5-8
Operation ........................................................................................................................................................... 9-13
Maintenance and Troubleshooting.....................................................................................................................14-18
Illustrated Parts List ...........................................................................................................................................19-26
Go to http://www.billygoat.com for French-Canadian translations of the product manuals.
Visitez http://www.billygoat.com pour la version canadienne-française des manuels de produits

Form No F060711D 3 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
MV 650 SERIES SPECIFICATIONS
MV650SPH MV600SPE
Engine Type Honda GSV190AA1A Briggs and Stratton 122MO70110F1
Horsepower 6.5 (4.85 kW) 6.25 (4.66 kW)
Fuel Capacity 1.6 qt (1.5 L) 1qt (.9L)
Oil Capacity 0.58 qt (0.54L) 0.63 qt (0.59L)
Unit Weight 179 lbs (81.2 kg) 179 lbs (81.2 kg)
Shipping Weight 208 lbs (94.3 kg) 208 lbs (94.3 kg)
Overall Dimensions 28” Wide x 62.5” Long x 45.5” High 28” Wide x 62.5” Long x 45.5” High
Maximum Operating Slope 20o20o
In compliance with 2000/14/EEC
standards 103 dB(a) at 3320 rpm 103 dB(a) at 3320 rpm
Sound at operators ear 83 dB(a) at 3320 rpm 83 dB(a) at 3320 rpm
SOUND DATA
SOUND LEVEL 103 Dba at Operator Position
Sound tests were conducted in accordance with 2000/14/EC as well as ISO11094, and were performed on 5-17-2005 under the conditions listed
below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit
for the sound power level for your model.
General Conditions: Sunny
Temperature: 66.2oF (19oC)
Wind Speed: 8.5 mph (13.7kph)
Wind Direction: South Southwest
Humidity: 59%
Barometric Pressure: 29.9” Hg (101.35kPa)
VIBRATION DATA
VIBRATION LEVEL 1.43g(14.00m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test
equipment. Tests were performed on 5-24-2006 under the conditions listed below.
General Conditions: Sunny
Temperature: 73.7oF (23.2oC)
Wind Speed: 8.05 mph (3.6m/s)
Wind Direction: South
Humidity: 83.5%
Barometric Pressure: 29.91” Hg (101.31 kPa)

Part No 840245 4 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ®MV Vacuum. If any labels are damaged or missing,
replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are
provided for convenience in ordering replacement labels. The correct position for each label may be determined by
referring to the Figure and Item numbers shown.
PN 400268
(See Figure 3 Item 55) PN 890254 (See Figure 4 Item 162) PN 840054 (See Figure 1 Item 34)
PN 400424
(See Figure 1 Item 11) PN 810736 (See Figure 4 Item 174) PN 890301 (See Figure 4 Item 163)
PN 900327
(See Figure 2 Item 118) PN 840080 (See Figure 4 Item 175) PN 500176 (See Figure 2 Item 120)
ENGINE LABELS CONTROLS
HONDA
Throttle Drive
P/N 840045 P/N 510127

Form No F060711D 5 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
MV Vacuum Assembly Drawing

Part No 840245 6 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
PARTS LIST

Form No F060711D 7 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
ASSEMBLY INSTRUCTIONS
Your BILLY GOAT ®MV Vacuum was shipped in one carton, completely assembled except for the Hood/Upper
Handle Assembly. Mounting hardware for the Hood/Upper Handle Assembly is temporarily installed on the lower
handle and the Housing assembly.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box since Hood/Upper Handle Assembly is
attached to the unit by cables.
Remove unit from carton. Make sure the following items that have been packed with unit:
Parts bag P/N 840187
Owner’s Manual, P/N 840245
General Safety and Warnings Manual, P/N 100294
Declaration of Conformity, P/N 840204
Honda Engine Manual
Warranty Card, P/N 400972
Ty-Wraps (2 ea)
Hardware Bag
DISCONNECT spark plug wire before assembling unit.
1. Attach hood assembly to the housing then hold in place
during the step 2.
NOTE: BE SURE ALL CABLES ARE ROUTED ON THE
UNDERSIDE OF THE HOOD AND HOUSING.
2. Install item #170 center bolt first when aligned with
a nut on the housing.
3. Attach rest of hood assembly to the housing using
corresponding hardware.
NOTE: You will have to insert the bolt/washer from
the inside by reaching through the hood.
- Two 7/16” wrenches.
1st

Part No 840245 8 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
4. Attach upper handle brace to lower handle using
corresponding hardware. Then repeat this step on the
other side.
- Two 1/2” wrenches.
5. Attach rod end (164) to the nozzle door rod then
secure in place by tightening jam nut.
6. Attach nozzle door rod to the nozzle door using
corresponding hardware.
NOTE: It is easier to do this with nozzle door closed.
- Two 9/16” wrenches.
7. Attach rod end to rod (as in step 5).
8. Attach nozzle door rod to the lever with
nozzle door closed and lever in hose kit
position.
NOTE: Check to see nozzle door open and
close all the way (see page 15). Tighten or
loosen the rod end (164) for any
adjustments.
Two 9/16”
wrenches.
9. Install cable ty wraps. 10. Reconnect spark plug
wire.
11. Attach the bag.
HERE
HERE

Form No F060711D 9 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
OPERATION
OPERATOR CONTROLS
The operator’s position is at the rear of the machine between the handlebars. The operator should STAND in a position to allow
both handlebars to be grasped firmly, which allows sufficient leverage to steer the machine. Operator’s controls are shown below.
Operator Control Locations
1 Drive Clutch Lever 4 Throttle Control
2 Bag Latch 5 Drive Shifter Control
3 Pull Starter 6 Nozzle Door Adjuster
STARTING
CHECK engine oil level before operating machine.
1. Place equipment on a level, firm surface that is free of rocks or other debris.
2. Place throttle in START position.
Throttle
DO NOT START equipment without the debris bag in place.
1
2
3
4
6
5

Part No 840245 10 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
3. Secure the unit with left hand at the handle then pull starter rope with right hand to start engine.
PULL STARTER CORD slowly until resistance is felt. Then pull cord rapidly to avoid kickback.
4. Move throttle control back to FAST position and allow engine to reach correct operating speed.
5. For Electric models: Set the throttle to the fast position, then pull up and push forward on the start switch.
Choke if needed
VACUUM NOZZLE HEIGHT ADJUSTMENT
FOR MAXIMUM PICKUP: Adjust nozzle height as close to debris as possible, but without blocking airflow into the nozzle. NOTE:
Never bury nozzle into debris. The vacuum nozzle is raised and lowered by turning the crank handle clockwise and counter-
clockwise.
SECURE UNIT AT
THE HANDLE
WITH LEFT HAND
DURING START
PULL ROPE
STARTER WITH
RIGHT HAND
On Electric
models only

Form No F060711D 11 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
VACUUM NOZZLE DOOR ADJUSTMENT
The vacuum nozzle door adjusts for the maximum performance under various applications.
Nozzle fully opened. This is ideal for turf application
Nozzle half way opened. This is ideal for hard surface application
Nozzle closed for OPTIONAL hose kit. This is ideal for hard to reach places.

Part No 840245 12 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
VACUUMING OPERATION
This machine is designed for vacuuming leaves, grass clippings, and other types of organic litter.
Debris mixed with cans, bottles, and small amounts of sand can be vacuumed; however, it is not this machine's
primary purpose. Vacuuming cans, bottles, and sand will affect the longevity of your machine. In dusty conditions it
maybe necessary to purchase Felt Bag Kit (P/N 840022).
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for
damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See
parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 23).
1. Move Shift Lever to correct position (1, 2, or 3) for desired gear.
Gear Shift Lever
2. Squeeze the Drive Clutch lever against the handle to engage the drive.
Drive Clutch Lever
SHUT DOWN
1. Release Drive Clutch Lever to disengage the drive.
2. Pull Throttle Control all the way back to the STOP position.

Form No F060711D 13 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
CLEARING A CLOGGED NOZZLE
DISCONNECT spark plug wire before servicing unit.
1. Shut engine off and wait for impeller to stop completely.
2. Disconnect spark plug wire.
3. Wearing durable gloves, remove clog.
WEAR durable gloves. Clog may contain sharp materials.
4. Reconnect spark plug wire.
DEBRIS BAG
Debris bags are normal replaceable wear items.
Frequently empty debris to prevent bag overloading with more weight than you can lift.
Bag liners are available for use in various conditions where debris will be vacuumed. (see Bag Liner Options shown
on page 1).
DO NOT place bag on or near hot surface, such as engine.
Be sure engine has come to a complete stop before removing or emptying bag!!.
This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings
page 4-5).
Many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas.
However, following these rules will help maintain your machine's ability to vacuum in dusty conditions:
•Run machine at idle to quarter throttle.
•Machine or pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry
before use.
Having one or more spare Felt Filter (840194) is a good way to reduce down time while dirty bags are being
cleaned.

Part No 840245 14 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation Every
Use Daily or Every 5 Hours Every 25 Hours Every 50 Hours Every 100-150 Hours
Inspect for worn or damaged parts. z
Check for excessive vibration z
Inspect for loose parts. z
Clean Debris Bag z
Lubricate clutch control lever (Use white lithium grease or equiv.)
LOCATION 1 z
Lubricate height adjuster LOCATION 2
z
Check drive clutch cable tension. z
Replace drive belts. z
COMMON REPLACEMENT PARTS
•Bag. P/N 840189. Original equipment replacement bag.
•Skid. P/N 840041. Nozzle wear guard skid.
•Drive Belt P/N 840066, Original equipment replacement belt
LOCATION 1 LOCATION 2
Apply lubricant on the zinc die cast barrel. Apply lubricant on the thread.
HERE
HERE

Form No F060711D 15 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
IMPELLER REMOVAL
READ all safety instructions before servicing unit.
DISCONNECT spark plug wire before servicing unit.
Tools required:
-1/2” socket, 3/8” drive
-ratchet, 3/8”
-drive extension, 3/8” drive
-universal joint, 3/8” drive
-pry bar or long screwdriver
-jack stands or similar device adequate to support weight of machine.
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove belt cover by removing 5 screws.
4. Detach drive belt from the transmission pulley by rotating the transmission assembly to relieve belt tension.
5. Remove engine, impeller and mounting plate by removing bolts around outside of housing.
6. Leaving engine fastened to plate, remove impeller bolt and lock washer and slide impeller off crankshaft ( A
puller may be required). CAUTION: Do not drop impeller.
7. If impeller does not slide off crankshaft, place two crowbars between impeller and housing on opposite
sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck
impeller.
8. If the impeller cannot be loosened, obtain a 1” (25.4mm) longer bolt of the same diameter and thread type as
the impeller bolt. Invert engine and impeller and support engine above ground to prevent recoil damage.
Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or wheel puller
against the bolt head and the impeller back-plate (near the blades), remove impeller from shaft.
9. To reinstall impeller, use a new impeller bolt and lockwasher
10. Tighten impeller bolt. Torque impeller bolt to 33-38 Ft. Lbs. (45-52 N.m).
11. Reinstall engine, impeller, and mounting plate onto housing in reverse order of removal.
12. Before connecting spark plug wire, slowly pull engine starting rope to insure that impeller rotates freely.
13. Reconnect spark plug wire.
DRIVE CLUTCH CABLE ADJUSTMENT
READ all safety instructions before servicing unit.
DISCONNECT spark plug wire before servicing unit.
Tools required:
-Ratchet wrench with 6” extension and 3/8” socket.
-Two 10mm open end wrenches.
-Tape measure.

Part No 840245 16 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
cable adjustment
4"
from
handle Tighten
Loosen
Procedure:
1. Wait for engine to cool and DISCONNECT SPARK PLUG!
2. Engage the clutch lever then pull the unit back until it stops freewheeling. The clutch lever should engage
around 2 5/16” of travel or 4 inches from tip of lever to handle.
3. Tighten or loosen cable adjuster nut next to the clutch lever until drive engages at 4” from handle.
4. Holding the adjuster nut in place with one wrench tighten cable lock nut firmly.
5. Readjust as needed.
6. RECONNECT SPARK PLUG!
7. Test run unit to insure proper operation after this or any other maintenance procedure.
8. If clutch still will not engage at 4” from handle, remove guard retaining screws and guard.
9. Measure the amount of spring stretch. Spring should measure 1 1/8” when engaged (Lever 4” from handle).
10. Release clutch lever and then move it to engagement position again and hold it, check the spring length to
assure it stayed in adjustment.
11.Re-install guard and fasteners.
DRIVE BELT REMOVAL AND REPLACEMENT
READ all safety instructions before servicing unit.
DISCONNECT spark plug wire before servicing unit.
Tools required:
-3/8” drive ratchet
-3/8” and ½” socket wrenches
-3/8” and 5/16” wrench
Procedure:
1. Wait for engine to cool completely and DISCONNECT SPARK PLUG.
2. Remove guard fasteners and guard.
3. Remove throttle control cable from engine.
4. Unplug wiring harness wire at engine.
5. Tilt transmission input pulley toward engine and remove the belt from it upward.
6. Remove all six screws fastening the engine base plate to the housing.
7. Lift engine assembly from housing.
8. Slide belt inward under the engine and off downward around impeller.
9. Install new belt in reverse order of belt removal.
10. Note: before placing new belt on transmission pulley look under the engine to insure the belt is properly in
the groove of the engine pulley.
11. Install engine assembly in reverse order of removal.
12. RECONNECT THE SPARK PLUG
INCREASE 2 1/16”
1 1/8"

Form No F060711D 17 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
INSTALLING NEW DRIVE CHAIN/ALIGNMENT/TENSION
READ all safety instructions before servicing unit.
DISCONNECT spark plug wire before servicing unit.
Tools required:
-7/16” and 1/2” socket.
-7/16” and 1/2” combination wrench.
-“Needle nose” pliers
-Flat head screwdriver
Allow the engine to cool completely and DISCONNECT THE SPARK PLUG.
1. Unfasten and remove the guard.
2. Rotate left rear wheel to bring the chain “master link” into view on the axle
sprocket.
3. Using the needle nose pliers carefully remove master link retaining spring
clip.
4. Slide the master link from the chain and remove the chain.
5. Thread the new chain onto the sprockets, place the ends of the chain on the
axle sprocket, this makes it easier to hold the chain in place when you slide
the new master link in place.
6. Install the new master link and CAREFULLY install the retaining clip.
7. Rotate left rear wheel to find the location where the chain is tightest (there
are always slight variations in the sprockets that make the chain tighter at
places in its rotation).
8. Rotate the axle several times and listen for “popping” or “clacking” this
indicates too much tension on the chain or misalignment of the chain. Skip
to Step 12 if no “popping” or “crackling” occurs.
Improper Chain Tension
9. At the point where the chain is tightest check the chain to for ¼” to ½” total
slack halfway between the axle sprocket and the transmission sprocket.
Skip to Step 11 if the deflection is correct.
10. Loosen 4 nuts holding the bearing bracket (see Fig 1) slide it very slightly
forward to tighten the chain or slide backward to loosen. Tighten 4 nuts
back then check the chain deflection. Repeat this step if necessary.
Improper Chain Alignment
11. Loosen 5 bolts securing the drive system (see Fig 2) slide it left or right
then check the alignment using straight edge. Tighten 5 bolts then repeat
Step 8.
12. Reinstall the guard and all of its fasteners.
13. RECONNECT THE SPARK PLUG.
Fig 2
Fig 1

Part No 840245 18 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
WIRING DIAGRAMS
Bag Switch Circuit Schematic Diagram
TROUBLESHOOTING
Problem Possible Cause Solution
Will not vacuum or has poor vacuum
performance. · Dirty or full debris bag or filter. · Clean debris bag and filter. Shake bag clean or wash.
· Nozzle height set too high or too low. · Adjust nozzle height (see page 14).
· Hose kit cap missing. · Check for hose kit cap.
· Clogged nozzle or exhaust. · Unclog nozzle or exhaust (see page 5)
· Excessive quantity of debris. · Allow air to feed with debris.
Abnormal vibration. · Loose or out of balance impeller. · Check impeller and replace if required.
· Loose engine. · Check engine.
Engine will not start. · Throttle in off position. · Check throttle control (see page 13).
· Engine not in full choke position. · Check throttle, choke position (see page 13).
· Out of gasoline or bad, old gasoline. · Check gasoline.
· Spark Plug wire disconnected. · Connect spark plug wire.
· Gas valve off. · Turn on gas valve.
· Dirty air cleaner. · Clean or replace air cleaner. Contact a qualified
service person.
· Safety Interlock disengaged on bag plate. · Latch the bag properly or check the bag rod to
see if it is bent.
Engine is locked, will not pull over. · Impeller plugged or clogged. · Remove debris (see page 16).
· Engine problem. · Contact an engine servicing dealer for engine
problems.
No self-propelling · Drive clutch not engaged · Engage the drive clutch lever.
· Transmission not in gear. · Check transmission shift control (see page 16).
· Drive belt worn or broken · Check the drive belt.
· Drive clutch cable out of adjustment or broken. · Check the drive clutch cable (see page 20).
· Spring tension too loose · Check spring legnth (see page 20).
· Drive chain off the sprocket. · Check the drive chain (see page 22).
Self propelled drive will not release · Improper drive clutch cable adjustment or
cable is kinked. · Check the drive clutch cable (see page 20).
Noisy or broken chain · No chain lubrication. · Lubricate chain.
· Chain misalignment or tension. · Check the drive chain (see page 22).

Form No F060711D 19 Part No 840245
MV650SPH Self-Propelled Vacuum Owner’s Manual
ILLUSTRATED PARTS LIST
Nozzle Assembly
Figure 1

Part No 840245 20 Form No F060711D
MV650SPH Self-Propelled Vacuum Owner’s Manual
Nozzle Assembly Parts List
ITEM NO. PART NUMBER DESCRIPTION MV650SPH QTY. MV600SPE QTY.
1 350127 YOKE 1/2 - 20 1 1
2 350128 PIN YOKE 1/2" 1 1
3 8024060 BOLT CARRIAGE 3/8-16X1 1/2" ZP 2 2
4 8172009 WASHER 3/8" SAE ZP 2 2
5 8161042 NUT LOCK 3/8-16 LT WT THIN ZP 2 2
6 8041038 SCREWCAP 5/16 -18 x 3 1/2 1 1
7 8160002 NYLON INSERT LOCKNUT 5/16-18 UNC 3 3
8 8172020 WASHER FLAT FENDER 5/16 1 1
9 8161044 NYLON INSERT LOCKNUT 1/2-13 UNC THIN 2 2
10 8171002 WASHER 1/4" FC ZP 3 3
11 400424 LABEL WARNING OPEI 1 1
12 8024050 BOLTCARRIAGE 5\16-18X3 1\2 2 2
13 520156 ROLL PIN 1/4 X1 LONG 2 2
14 8172011 WASHER 1/2" SAE ZP 2 2
15 840118 NOZZLE MV VAC ASSEMBLY 1 1
16 840019 CAP 5 IN HOSE VAC 1 1
17 840024 HANDLE LOWER MV VAC 1 1
18 840101 WHEEL 14" ASSEMBLY WITH BEARING AND TIRE 2 2
19 840104 AXLE FRONT WA MV VAC 1 1
20 840155 BRACKET HGT ADJ WA W/LABEL MV VAC 1 1
21 8041004 SCREWCAP 1/4 - 20 x 0.75 HWH 1 3
22 840034 LINK HGT ADJ MV VAC 1 1
23 840041 BRACKET NOZZLE WEAR GUARD MV VAC 2 2
24 840029 ROD CONNECT HGT ADJ 1 1
25 840073 BUSHING 0.5" ID 0.625 OD XX0.250 1 1
26 840119 ROD HANDLE CRANK ASSEMBLY 1 1
27 840057 HANDLE CRANK 0.5 ID X3.72 LONG 1 1
28 840078 BUSHING 3/8" ID 1/2" OD X3/8" LONG 2 2
29 840158 WASHER LOCK 1/4" TWISTED TOOTH 1 1
30 840207 NUT PAL 0.5" ID x 0.75 OD 2 2
31 840135 NOZZLE COVER MV VAC 1 1
32 840055 LABEL PRODUCT DECAL MV 1 1
33 840035 SCREW PLASTIC 5/8 8 8
34 840054 LABEL HGT ADJ MV VAC 1 1
35 8122082 SCREW SELF-TAP 5/16 NC X3/4 HEX 2 4
36 840088 BRACKET NOZZLE COVER REINFORMENT MV 1 1
37 8024021 BOLT CARRIAGE 1/4-20X0.75 3 3
38 900455 NUT FLANGE 1/4-20 3 3
100 8172007 WASHER 1/4" SAE ZP - 4
195 840017 MV WHEEL BEARING 2 2
201 840117 SOLENOID ELEC START - 1
202 840198 BRACKET SOLENOID MOUNT MV - 1
209 8181007 WASHER LOCK 1/4" EXT TOOTH - 2
211 8142001 NUT 1/4" FIN HEX ZP - 2