Billy Goat SC181H User manual

NOT FOR REPRODUCTION

2 billygoat.com
Table of Contents:
Intended Use......................................................................... 3
Specifications........................................................................ 3
California Proposition 65..................................................... 3
Initial Setup............................................................................3
Uncrating The Unit........................................................... 3
Setup Checklist.................................................................3
Features and Controls..........................................................3
Instructional Decals.......................................................... 3
Drive Controls...................................................................5
Blade Engage Lever.........................................................5
Engine Stop Switch.......................................................... 5
Blade Height Adjuster...................................................... 6
Free Wheel Lever.............................................................6
Choke-Throttle Combination Lever.................................. 6
Operation............................................................................... 7
Before Operation.............................................................. 7
General Operation............................................................ 7
Periodic Maintenance........................................................... 7
Belt Maintenance.................................................................. 8
Replacing the Drive Belt.................................................. 8
Replacing the Blade Belt..................................................8
Cable Maintenance............................................................... 8
Adjusting Cable Tension.................................................. 8
Blade Maintenance............................................................... 9
Checking the Blade.......................................................... 9
Replacing the Blade......................................................... 9
Troubleshooting.................................................................... 9
NOT FOR REPRODUCTION

3
Intended Use
This machine may only be utilized for the purpose for which it
was designed. This machine is designed to cut 18" (45.7cm)
wide strips of turf. Be sure that all operators of this equipment
are trained in general machine use and safety.
WARNING
Wheels can skid while operating in poor conditions. Terrain
that is too dry or too wet can cause wheel skidding. Only
operate on damp terrain, so that the Sod Cutter blade
encounters slight resistance.
Specifications
DIMENSIONS
Overall Length 60" (152 cm)
Overall Width 26.5" (67.3 cm)
Overall Height 38.5" (97.8 cm)
Total Unit Weight 395 lb (179 kg)
Maximum Operating Slope 20°
ENGINE
Type: Honda
Model: GXV160UH2N1XB
Fuel Capacity: 1.48 qt (1.4 L)
Oil Capacity: 0.69 qt. (0.65 L)
California Proposition 65
WARNING
This product can expose you to chemicals including
gasoline engine exhaust, which is known to the State of
California to cause cancer and carbon monoxide, which
is known to the State of California to cause birth defects
or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Initial Setup
Your Sod Cutter is shipped from the factory in a wooden
crate. The unit is shipped completely assembled. You will
need to uncrate the unit and follow the Setup Checklist.
Uncrating The Unit
1. Use a prybar to open the crate from the back.
2. Locate the Free-Wheel Lever on the unit. Pull the lever to
set the unit into free-wheel motion position. This will allow
the unit to roll out of the crate with ease.
3. Grasp the unit's handlebars and pull the unit out of the
crate.
Setup Checklist
Complete the following items before operation:
• Read the General Safety Manual. Read how to operate
your unit safely to prevent injury to yourself or others.
• Read the Owner's Manual to familiarize yourself with
the unit. Read how to operate and maintain your unit for
optimum performance.
• Register your unit for warranty either through your
Authorized Dealer or online.
• Wear appropriate clothing for operation or maintenance
such as closed toe shoes, hearing protection, and eye
protection. Tie back loose hair.
• Be aware of surroundings during operation. Avoid
obstacles that could damage the blade. Do not operate
the unit under poor conditions.
• Add oil to the engine before starting.
• Check the gasoline. Replace old or bad gasoline.
• Grease the unit's bearings before use or as needed. Use
only NLGL Grade 2 Multipurpose Lithium-Based Grease.
Features and Controls
Instructional Decals
The instructional decals shown below were installed on your
new Billy Goat 18" Sod Cutter. If any decals are damaged
or missing, replace them before operation. Use the images
and corresponding part numbers when ordering replacement
labels.
NOT FOR REPRODUCTION

4 billygoat.com
1
A. 373500 - Decal, Console
B. 373501 - Decal, Blade Arm
C. 373503 - Decal, Height Adjuster
D. 373504 - Decal, Drive Enable
E. 373505 - Decal, Service Instructions
F. 400424 - Decal, Warning Sharp
G. 830502 - Decal, Oil Chain
H. 371501 - Decal, Caster Left
I. 371504 - Decal, Caster Right
J. 100263 - Decal, Throttle
373500 - Decal, Console
373501 - Decal, Blade Arm
373503 - Decal, Height Adjuster
373504 - Decal, Drive Enable
NOT FOR REPRODUCTION

5
373505 - Decal, Service Instructions
400424 - Decal, Warning Sharp
830502 - Decal, Oil Chain
371501 - Decal, Caster Left
371504 - Decal, Caster Right
Drive Controls
The drive controls are located on each side of the operator
console. Engage the right lever to move forward (A, Figure
2). Engage the left lever to move in reverse (B). To increase
speed, depress the lever gradually. Depress the lever fully for
maximum speed. The forward and reverse controls cannot be
operated simultaneously. Drive either in forward or reverse.
Do not attempt zero-turn motion.
2
Blade Engage Lever
The blade engage lever is located on the upper left hand
side of the operator console (C, Figure 2). Depress the lever
completely to engage the blade, lowering it to cut into the sod.
Be sure to set the desired blade height before engaging the
blade.
Engine Stop Switch
The engine stop switch is conveniently located on right of the
operator console (D, Figure 2). To turn on the unit, move the
switch to the "ON" position.To turn off the unit, move the
switch to the "OFF" position.
NOT FOR REPRODUCTION