Billy Goat AET60 User manual

Part No. 100384
1
AET60 Owner’s Manual
Original Instructions
IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE
AERATOR 60” Owner's Manual
AET60
Beginning Serial #: 022417472
NOT FOR REPRODUCTION

Part No. 100384
2
Table of Contents
Specications, Intended Use, Replacement Parts & Safety
Instruction Labels, Packing Checklist, & Assembly
Operation
Maintenance and Troubleshooting
Illustrated Parts and Part Lists
Tine Replacement Kit Information
3
4
5-6
6
7-8
9
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
3
Specications
Total Unit Weight 443lb (201kg)
Width 37”-48”-60”
Maximum Operating Slope 15 °
Intended Use
Replacement Parts
Table 1: Specications
Your Billy Goat®Aerator
This machine is designed for aerating established lawns and large grass covered areas.
The machine should not be used for any other purpose than that stated above.
DO NOT OPERATE IF EXCESSIVE VIBRATION OCCURS!
If excessive vibration occurs, stop use of the unit immediately and check for damaged
or worn reel, loose hardware, or lodged debris.
Handling and Transporting
Always use four or more people to lift this machine. Lift holding on either side of the
machine, using the handles and the frame. Secure in place during transportation. See
specications for unit weight.
For safety use gloves when lifting.
P/N 360100
Replacement tip for
aerating tines.
TINE REPLACEMENT
Safety
PROPOSITION 65 STATEMENT
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to the State of California to cause birth de-
fects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
4
Instruction Labels
The labels shown below were installed on your Billy Goat® Aerator. If any labels are
damaged or missing, replace them before operating this equipment. Part numbers from the
Illustrated Parts List are provided for convenience in ordering replacement labels. The correct
position for each label may be determined by referring to the part numbers shown.
LABEL DANGER CLEAR
P/N 100311
LABEL MAX LOAD
P/N 100356
LABEL HARD SOIL
P/N 100372
LABEL HITCH MOUNT
P/N 100374
Packing Checklist
Your Billy Goat® AET60 is shipped from the factory in one carton, completely assembled.
Read all safety instructions before assembling unit.
Take caution when removing the unit from the box.
Boxing Parts Checklist
Owner’s Manual
P/N 100384
Assembly
1. The machine is fully assembled; you will need to attach to a vehicle in the desired conguration (see
operation section for details).
Parts Bag and Literature Assembly
• Warranty Card P/N - 400972
• Owner’s Manual P/N - 100384
• General Safety and Warranty
Renovation Manual P/N - 100295
• General Safety and Warranty
Manual P/N - 100295
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
5
Operation
Item numbers in parentheses can be referenced in the Parts Illustration and Parts List on pages 7-9.
Operating Instructions
The AET60 is a combination of a tow-behind aerator and a 3-point aerator with two wings for
adjustable aeration widths. When used behind a tractor in the 3-point application, there are pins on
each tine assembly that can be removed to allow tines to swivel, enabling the tractor to turn while still
aerating with the tines in the ground. When being towed, the tine assemblies must be locked in place
for proper tracking.
Aerating Operation
NEVER PARK THIS UNIT ON A SLOPE OF ANY KIND. Always keep tines in the up position when
parking the unit.
Using as a Tow-Behind
When using this machine as a towable aerator, the tow link should be in the down position and
attached to the frame of the aerator using the two clevis pins (item 19). The tow behind is telescoping
so that it can be extended to accommodate various vehicles. Make sure all ve lock pins (item 21) are
in place on the axle assembly to prevent the assembly from swiveling. When operating, the wings can
either be up or down depending on the width of aeration desired. In normal conditions, there will be
adequate weight for proper penetration when the wings are up; when the wings are down, additional
weight may be required.
Using in a 3-Point Application
When used with a tractor and a 3-point hook up, the inner and outer tow link should slide together and
be in the upright position holding it to the frame with the two clevis pins (item 19). The two table on the
outer tow link are for the center link on the 3-point. Remove the ve lock pins (item 21) from the tine
axle to allow the assembly to swivel.
Raising and Lowering Tines
The tines are raised or lowered into the ground by operating the crank on the cylinder to raise or lower
the tines to the desired depth. Tine penetration is very dependent on surface preparation. READ the
entire operation section before aerating.
•Set Tine Depth: With the aerator in the work area, lower the tines into the ground by rotating the
crank at the rear.
•Transport: Be sure to raise tines out of the ground before transporting away from the work area.
Caster Raising/Lowering
The caster can be raised or lowered by removing the pin and rotating the caster then reinserting the
pin to lock it into position. DO NOT transport with the caster in the down position so that it comes into
contact with the ground. DO NOT unhitch the unit on uneven terrain with the caster down as the unit
may roll. To prevent unwanted roll, chock the wheels.
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
6
Operation Continued
Tips
• Mow - Mow the lawn to its normal cut height.
• Water - For the best performance and maximum tine penetration the lawn should be thoroughly watered
the day before aeration.
• Inspect - Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can
present a hazard during work prior to starting
• Identify - Mark all xed objects to be avoided during work, such as sprinkler heads, water valves, buried
cables, or clothes line anchors, etc.
• Slopes - Do not operate the aerator on steep slopes (any slope exceeding 15°). Use extreme caution
when operating on any sloped surface. For lesser sloped areas operate the unit, traversing up and down at
a 45° angle to the slope rather than straight across. Extended operation on steep slopes can cause engine
damage.
Maintenance
Item numbers in parentheses can be referenced in the Parts Illustration and Parts List on pages 7-9.
Periodic Maintenance
Periodic maintenance should be performed at the following intervals:
Maintenance Operation* Every Use (or daily) Every 10 hrs Every 50 hrs
Inspect for loose, worn, or
damaged parts •
Thoroughly clean all debris
from unit and tines •
Grease wheel bearings and
tine hubs •
Table 2: Maintenance
Troubleshooting
Problem Possible Cause Solution
Abnormal Vibration Damaged or missing tines. Loose
bolts.
Stop work immediately. Replace any
damaged or missing tines. Tighten all
loose nuts and bolts.
Table 3: Troubleshooting
*Engine must be level when checking or lling oil
Individual Tine Replacement
1. Remove the bolt and nut (Items 46 and 43, respectively).
2. Replace the tine and then secure it in place with hardware previously removed.
Note: Tines are a normal wear item and should be inspected regularly for signs of wear or damage.
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
7
AET60 Parts Drawing
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
8
AET60 Parts List
Item No. Part No. Description Quantity
1 381556 BASE FRAME WELDMENT 1
2 381557 LEFT WING FRAME WELDMENT 1
3 381558 RIGHT WING FRAME WELDMENT 5
4 380237 TINE ARM WA AET60 GEN 2 5
5 381560 WHEEL ASSEMBLY 1
6 381561 JACK ASSEMBLY 1
7 381562 OUTER TOW LINK 1
8 381563 INNER TOW LINK 1
9 380234 HUB, EIGHT TINE 10
10 440153 WASHER 1.5 OD X 0.453 ID X 0.25 THK 10
11 381566 ARM SWIVEL STOP 5
12 381567 WING HANDLE 2
13 381568 BASE LOAD PAN 1
14 381569 WING LOAD PAN 2
15 373280 BEARING, 6205 25mm BORE ARMORED SEALS 20
16 8181011 WSHR-STL, BLV, 0.402 X 0.877 X 0.63 CN MZ 10
17 8041050 SCREWCAP 3/8”-16 X 1” HCS ZP 10
18 381573 TINE ARM SHOULDER BUSHING 10
19 381574 CLEVIS PIN 7/16” X 3.5” 2
20 500267 GRIP HANDLE 1” X 5.5” 2
21 381576 LOCK PIN 3/8” X 2.5” 6
22 381577 CLEVIS PIN 3/4” X 3.5” 1
23 381578 CLEVIS PIN 7/8” X 3” 2
24 381579 CLEVIS PIN 5/8” X 1.75” 2
25 8041175 SCREWCAP 3/4”-10 X 5 1/2” HCS ZP 2
26 381581 NUT JAM 3/4”-10 2
27 381582 CLEVIS PIN 5/8” X 5” 1
28 381583 CLEVIS PIN 5/8” X 3.5” 1
29 281584 COTTER HAIR PIN 1/8" FOR 3/4 TO 7/8" 3
30 281585 HITCH PIN 5/8” X 4” W/LYNCH PIN 3
31 381586 COTTER HAIR PIN 1/8” FOR 7/16 TO 5/8 8
32 381587 CLEVIS PIN 7/16” X 2.5” 2
33 360100 TINE CORING 3/4” 80
34 381589 CLEVIS PIN 5/8” X 4” 4
35 381590 RUBBER BUMPER 1.5” X .75” THK 4
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
9
AET60 Parts List Continued
Item No. Part No. Description Quantity
36 381591 RUBBER BUMPER 1.0” X 1.0” THK 8
37 80150057 SHCS 10-32 X 1/2” 14
38 8171008 WASHER 3/4” SAE 8
39 381158 SHCS 10-32 X 1.25” 8
40 381595 RUBBER BUMPER 1.5” X 1.5” THK 2
41 381596 SHCS 1/4”-20 X 1.5” 2
42 381597 SHCS 1/4”-20 X .75” 4
43 8165003 NUT-HEX-NYLK, FLG 0.375” - 16 ZP 85
44 8041058 SCREWCAP 3/8”-16 X 3” HCS ZP 5
45 381440 WHEEL 13” 2
46 8041052 SCREWCAP 3/8”-16 X 1 1/2” HCS-ZP 80
47 8160002 NUTLOCK 5/16”-18 4
49 816003 NUTLOCK 3/8”-16 HEX ZP 5
50 8041010 SCREWCAP 1/4”-20 X 2” HCS ZP 2
51 8160001 NUTLOCK 1/4”-20 HEX ZP 4
52 8197031 COTTER PIN 1/8” X 1” 4
53 8172020 WASHER FENDER 5/16” 8
54 380134 TRANSPORT WHEEL STAND 1
55 610101 CASTER 5” DIA X 2” 1
56 8171003 WASHER 5/16” FLAT 8
57 8041028 SCREWCAP 5/16”-18 X 1” GR 5 HCS ZP 4
58 8041057 SCREWCAP 3/18”-16 X 2 3/4” ZP 5
59 380235 AXLE TINE ARM GEN 2 5
60 380236 SPACER, SPINDLE BEARING AET60 10
NOT FOR REPRODUCTION
100384_A_LO

Part No. 100384
10
Item No. Part No. Description Quantity
4 380237 TINE ARM WA AET60 GEN 2 1
9 380234 HUB, EIGHT TINE 2
10 440153 WASHER 1.5 OD X 0.453 ID X 0.25 THK 2
11 381566 ARM SWIVEL STOP 1
15 373280 BEARING, 6205 25mm BORE ARMORED SEALS 4
16 8181011 WSHR-STL, BLV, 0.402 X 0.877 X 0.63 CN MZ 2
17 8041050 SCREWCAP 3/8”-16 X 1” HCS ZP 2
21 381576 LOCK PIN 3/8” X 2.5” 1
33 360100 TINE CORING 3/4” 16
43 8165003 NUT-HEX-NYLK, FLG 0.375” - 16 ZP 16
44 8041058 SCREWCAP 3/8”-16 X 3” HCS ZP 1
46 8041052 SCREWCAP 3/8”-16 X 1 1/2” HCS-ZP 16
49 8160003 NUTLOCK 3/8”-16 HEX ZP 1
58 8041057 SCREWCAP 3/18”-16 X 2 3/4” ZP 1
59 380235 AXLE TINE ARM GEN 2 1
Tine Replacement Kit Information
The new Billy Goat® AET60 is built with newly designed tines. Owners of previous Billy Goat AET60 models
can purchase new tines in the form of a service kit (Part No. 380238). New owners can replace old or worn
tines with the same service kit.
To order a service kit, please visit www.billygoat.com or contact Billy Goat customer service at [phone].
Your Billy Goat® Tine Replacement Kit will include the necessary instructions/literature
and the following parts:
NOT FOR REPRODUCTION
100384_A_LO