Binks 104165 User manual

• Model 104165
Service Manual EN
Auto Changeover Panel

EN

EN
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT
ALL POWER SOURCES DURING MAINTENANCE. Failure to e-
energize, isconnect an lock out all power supplies before
performing equipment maintenance coul cause serious injury or
eath. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF
AN EMERGENCY.
NOISE LEVELS. The A-weighte soun level of pumping an
spray equipment may excee 85 B(A) epen ing on equipment
settings. Actual noise levels are available on request. It is
recommen e that ear protection is worn at all times while
equipment is in use.
PACEMAKER WARNING. You are in
the presence of magnetic fiel s
which may interfere with the
operation of certain pacemakers.
PROJECTILE HAZARD. You may be
injure by venting liqui s or gase
that are release un er pressure, or
flying ebris.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for
worn or broken parts on a aily basis. Do not operate the
equipment if you are uncertain about its con ition.
HIGH PRESSURE CONSIDERATION. High pressure can cause
serious injury. Relieve all pressure before servicing. Spray from
the gun, hose leaks or rupture components can inject flui into
your bo y an cause extremely serious injury. KEEP EQUIPMENT GUARDS IN
PLACE. Do not operate the
equipment if the safety evices have
been remove .
STATIC CHARGE. Flui may evelop a static charge that must be
issipate through proper groun ing of the equipment, objects to
be spraye an alll other electrically con uctive objects in the
ispensing area. Improper groun ing or sparks can cause a
hazar ous con ition an result in fire, explosion or elecrtic shock
an other serious injury.
PROP 65 WARNING. WARNING:This pro uct contains chemicals
known to the state of California to cause cancer an birth efects
or other repro uctive harm.
PINCH POINT HAZARD. Moving parts
can crush an cut. Pinch points are
any areas where ther are moving
parts.
IT IS THE ESPONSIBILITY OF THE EMPLOYE TO P OVIDE THIS INFO MATION TO THE
OPE ATO OF THE EQUIPMENT.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
proce ure in the equipment
instruction manual.
NEVER MODIFY THE EQUIPMENT.
Do not mo ify the equipment unless
the manufacturer provi es written
approval.
OPERATOR TRAINING. All personnel
must be traine before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpecte ly an
result in serious injury.
WA NING
Rea the following warnings before using this equipment.
READ THE MANUAL. Before operating finishing equipment, rea
an un erstan all safety, operation an maintenance
information provi e in the operation manual.
WEAR SAFETY GLASSES. Failure to wear safety glasses with si e
shiel s coul result in serious eye injury or blin ness.
In this part sheet, the words WA NING, CAUTION and NOTE are used to emphasize important safety
information as follows:
WA NING CAUTION NOTE
Hazar s or unsafe practices which coul result
in severe personal injury, eath or substantial
property amage.
Hazar s or unsafe practices which coul result
in minor personal injury, pro uct or property
amage
Important installation, operation or
maintenance information.
AUTOMATIC EQUIPMENT. Automatic
equipment may start su enly
without warning.

EN
Outline Dimensions

EN
Mounting Dimensions

EN
Panel Layout

EN
Installation Schematic

EN
Binks pro ucts are covere by Carlisle Flui Technologies five year materials an
workmanship limite warranty. The use of any parts or accessories, from a source other
than Carlisle Flui Technologies, will voi all warranties. For specific warranty
information please contact the closest Carlisle Flui Technologies location liste below.
Carlisle Fluid Technologies reserves the right to modify equipment specifications without prior notice.
DeVilbiss®, ansburg®, MS®, BGK® and Binks® are registered trademarks of Carlisle Fluid Technologies,
Inc.
© 2016 Carlisle Fluid Technologies, Inc.
All rights reserved.
France Germany
WA ANTY POLICY
www.carlisleft.com.cn
[e-mail]
Tel: [phone]
Fax: [phone]
www.ransburg.co.jp
[e-mail]
Tel: [phone]
Fax: [phone]
www.carlisleft.com.au
[e-mail]
Tel: [phone]
Fax: [phone]
www.carlisleft.eu
[e-mail]
Tel: [phone]
Fax: [phone]
www.carlisleft.eu
[e-mail]
Tel: [phone]
Fax: [phone]
www.carlisleft.eu
[e-mail]
Tel: [phone]
Fax: [phone]
China Japan
Binks is part of Carlisle Flui Technologies, a global lea er in innovative finishing
technologies. For technical assistance or to locate an authorize istributer, contact
one of our international sales an customer support locations below.
USA/Canada Mexico Brazil
Australia
www.binks.com
[e-mail]
Toll Free Tel: [phone]
Toll Free Fax: [phone]
www.carlisleft.com.mx
[e-mail]
Tel: [phone]
Fax: [phone]
www.devilbiss.com.br
[e-mail]
Tel: [phone]
Fax: [phone]
United Kingdom