Birlea CORO4SBPIN User manual

Vendor: S000238
Page 1 of 11
ASSEMBLY INSTRUCTIONS
CORONA 1 DOOR 4 DRAWER SIDEBOARD
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR CORONA 1 DOOR
4 DRAWER SIDEBOARD.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS:
Please check contents and read instructions carefully before commencing assembly.
To avoid damages assemble the item on a soft, clean surface.
Assemble in the room of use.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fi ings are secured.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Keep small parts out of the reach of children.
CARE & MAINTENANCE:
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to the production process, however, this will disappear
after a period of time.
DO NOT place the item ne t to a radiator or direct sunlight as this item is susceptible to temperature
change. It is recommended to maintain an even room temperature with no sudden fluctuations.
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as the use of these materials would invalidate any claims.
You may wish to re-treat the surface to maintain the original finish. This can be done using block wa (un-
perfumed). Please follow the manufacturer’s instructions carefully.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
Periodically check all screws & fi ings to ensure they are secure.
DO NOT push the item as this will damage the base.
Keep any sharp objects away from the item.
www.birlea.com

Vendor: S000238
Page 2 of 11
Parts L st Hardware L st
Part Descr pt on Qty Part Descr pt on Qty
1
Top Panel
1
A Wooden Dowel 38
2
Right
Panel
1
B 14 mm Screw 16
3
Left Panel
1
C 30 mm Screw 40
4
Centre Panel
1
D 35 mm Screw 32
5
Base Panel
1
E 40 mm Screw 6
6
Side Plinth
2
F 50 mm Screw 8
7
Front Plinth
1
G 19 mm Bolt 5
8
Right Front Frame
1
H
Handle
5
9
Left Front Frame
1
J Hinge 2
10
Top Front Frame
1
K
Clip
1
11
Bottom Front Frame
1
L
Plug
1
12
Vertical Front Frame
1
M
Stud
4
13
Horizontal Front Frame
3
N Tack 38
14
Drawer Front
4
** You w ll need a small mallet and a screwdr ver.
15
Drawer Side
8
16
Drawer Back
4
17
Drawer Base
4
18
Door
1
19
Back Panel
2
20
Side Drawer R nner
4
21
Centre
Drawer R nner
4
22
Cleat
4

Vendor: S000238
Page 3 of 11
Step 1: Attach the right front frame (8) to the right panel (2) with the cleats (22), hardware part D and a
screwdriver (not provided). Repeat for the left front frame (9) and left panel (3).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000238
Page 4 of 11
Step 2: Insert hardware part A using a small mallet (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 3: Join together the front frame components.
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 4: Attach the centre panel (4) to the base panel (5) using hardware part E and a screwdriver (not
provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.

Vendor: S000238
Page 5 of 11
Step 5: Join together the two sections using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.
Step 6: Attach the left panel (£) and right panel (2) using hardware part E and a screwdriver (not provided).
DO NOT use any power tools as th s may damage the frame and w ll nval date any cla m.