BIXOLON SRP-350plusV Instruction manual

Network Connection Manual
Thermal POS Printer
Ver. 1.00
http://www.bixolon.com

Network Connection Manual
Ver.1.00
- 2 -
Table of Contents
Copyright.........................................................................................................................3
1. Introduction................................................................................................................4
2. Precaution...................................................................................................................4
3. Specification................................................................................................................5
4. How to Connect ..........................................................................................................6
4-1 Connecting Printer........................................................................................................7
4-2 Check Network Setting .................................................................................................8
4-3 Initial Wireless LAN Connection (Windows 10)........................................................11
4-4 Initial Wireless LAN Connection (Android Soft AP mode) ......................................17
4-5 Initial Wireless LAN Connection (iOS Soft AP mode) ..............................................18
4-6 How to change Infrastructure mode ........................................................................19
5. Configuration............................................................................................................ 21
5-1 LAN Setting Values......................................................................................................21
5-2 WLAN Setting Values ..................................................................................................22
6. Ethernet / WLAN Test by using Windows Test Page ............................................ 23
7. Factory Reset ............................................................................................................ 30
7-1 Initializing Ethernet Setting .......................................................................................30
7-2 Initializing WLAN Setting............................................................................................31
8. Troubleshooting ....................................................................................................... 33

Network Connection Manual
Ver.1.00
- 3 -
Copyright
© BIXOLON Co., Ltd. All rights reserved.
This user manual and all property of the product are protected under copyright law.
It is strictly prohibited to copy, store, and transmit the whole or any part of the manual
and any property of the product without the prior written approval of BIXOLON Co.,
Ltd.
The information contained herein is designed only for use with this BIXOLON product.
BIXOLON is not responsible for any direct or indirect damages, arising from or
related to use of this information.
• The BIXOLON logo is the registered trademark of BIXOLON Co., Ltd.
•All other brand or product names are trademarks of their respective companies or
organizations.
BIXOLON Co., Ltd. maintains ongoing efforts to enhance and upgrade the functions
and quality of all our products.
In the following, product specifications and/or user manual content may be changed
without prior notice.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn
the printer “OFF”, before you connect or remove the cables on the rear side, in order
to guard the printer against the static electricity. If the printer is damaged by the static
electricity, you should turn the printer “OFF”.

Network Connection Manual
Ver.1.00
- 4 -
1. Introduction
This Network manual provides information on the connection of network with the
Industrial Label printer.
2. Precaution
1) The printer has to be within 100m(Outdoor) from AP(Access point) to connect
WLAN. Although 35m is able to communicate in door, WLAN could be affected by
environment to be shorten.
2) The maximum separating distance may be shortened if transmission obstacles,
such as cement walls, are present.
3) If a device (such as a microwave oven, wireless LAN, etc.) that uses the same
frequency is present, transmission may be interrupted. Separate the printer and
Bluetooth-enabled device from such interrupting devices by a distance of at least 5m.

Network Connection Manual
Ver.1.00
- 5 -
3. Specification
Categories
Feature
Implementation
LAN
Interface
10/100 Base-T All in one(Auto detection)
Protocol
DHCP Client, HTTP, ARP, ICMP, IPv4, TCP,
UDP
WLAN
Operation Mode Infrastructure, Soft AP, Ad-hoc, Wi-Fi Direct
Wireless
Standard
IEEE 802.11b/g/n, IEEE 802.11a/b/g/n
Range Up to 100m free space (Outdoor)
Security
WEP64/128
WPA1/2 - PSK
WPA1/2 – Enterprise
(EAP-TLS, EAP-TTLS, PEAP, LEAP,
EAP-FAST)
Management
WLAN Configuration tool, HTTP,
Smart connection APP

Network Connection Manual
Ver.1.00
- 6 -
4. How to Connect
Both Ethernet and WLAN can be configured through the printer’s LCD Display, USB,
Ethernet or WLAN interface.
When you want to change the Ethernet or WLAN of the printer, the network settings
of the host(PC, PDA, etc) and Ethernet or WLAN of the printer must configured properly
configured so that communication can be established.

Network Connection Manual
Ver.1.00
- 7 -
4-1 Connecting Printer
1) USB cable
Connect USB cable to Printer, PC device.
Use the “Net Configuration Tool” to adjust the settings.
2) WLAN
Connect to the AP (Access Point) configured in Infrastructure mode in order to connect
to the LAN/wireless network
Infrastructure mode
In order to configure the network between the wireless host device and the printer,
set the printer to Soft AP Mode.
Soft AP mode
* Soft AP mode is only supported on IFJ-WD.
A P

Network Connection Manual
Ver.1.00
- 8 -
4-2 Check Network Setting
1) Ethernet Interface Card
When the printer is booted, press the function button to output the network setting
value. It takes about 10 seconds to apply the LAN setting after turning on the power.
<LAN Information Printing >
LAN SETTING
MAC ADDRESS : 00:15:94:C2:6B:A8
IP ADDRESS : 192.168.0.48
SUBNET MASK : 255.255.255.0
GATEWAY : 192.168.0.1
PORT : 9100
INACT. TIME : 0
Function
Key

Network Connection Manual
Ver.1.00
- 9 -
2) On-Board Ethernet / WLAN
After the printer has finished booting, open the printer cover and press and hold the
FEED Button for 5 seconds. This will cause the interface setting confirmation mode.
Then add the paper, close the cover, and check that the following message is printed.
Error/Paper LED toggles when WLAN boots up.
The number of interface
setting information may be different for each
interface type of the product.
Checking Interface Setting
0: Exit
1: LAN Information Print
2: LAN Factory Reset and Reboot Printer
3: WLAN Information Print
4: WLAN Factory Reset and Reboot Printer
5 or more: None
Select Modes by Feed button control
as below.
Step 1. Short-press as many times as
The mode number to choose.
Step 2. Long-press over 1 second.
*e.g. To choose Mode 2, press Feed
Button 3 times(short-short-long)
Cover Open Button
Feed
Button

Network Connection Manual
Ver.1.00
- 10 -
If the above message is printed, select Mode 1 / 3, and you will see the following LAN
data.
-To select Mode 1, press the Feed button once quickly/ once long.
-To select Mode 3, press the Feed button three times quickly/ once long.
<LAN 정보 출력>
<WLAN Information Printing >
LAN SETTING
MAC ADDRESS : 00:15:94:C2:6B:A8
IP ADDRESS : 192.168.0.48
SUBNET MASK : 255.255.255.0
GATEWAY : 192.168.0.1
PORT : 9100
INACT. TIME : 0
WLAN SETTING
WLAN F/W VERSION : 02.00(3930)
SYSTEM NAME : SRP-350plusV
NETWORK MODE : SOFT AP
FREQUENCY : (Priarity) 2.4GHz/5GHz
AUTHENTICATION : OPEN
ENCRYTION : NONE
ESSID : PRINTER_B03223
DHCP : ENABLED
IP ADDRESS : 192.168.1.1
SUBNET MASK : 255.255.255.0
GATEWAY : 192.168.1.2
PORT : 9100
WLAN MACADDRESS :
0 0 1 5 9 4 B 0 3 2 2 3

Network Connection Manual
Ver.1.00
- 11 -
4-3 Initial Wireless LAN Connection (Windows 10)
• If a wireless LAN utility program is installed, set it using the program or exit the
wireless program and set it in the following orders.
1) Search the “Control Panel” and then Click the “Open”.
2) Search the “Control Panel” and then Click the “Open”.

Network Connection Manual
Ver.1.00
- 12 -
3) Click the “Change adapter settings”.
Click the “WiFi Properties”.
4) Select Internet Protocol Version 4(TCP/IPv4), and then click Properties.

Network Connection Manual
Ver.1.00
- 13 -
5) Set the IP settings as shown below, and then click OK.
6) Click the “Set up a new connection or network”.

Network Connection Manual
Ver.1.00
- 14 -
7) Click the “Manually create a wireless network”.

Network Connection Manual
Ver.1.00
- 15 -
8) ‘Network name’ = PRINTER_XXXXXX
‘Security type’ = Open,
Check “Start this connection automatically”,
“Connect even if the network is not broadcasting” and then click the “Next”

Network Connection Manual
Ver.1.00
- 16 -
9) Click the “Close”.
10) After completing configuration, PRINTER_XXXXXX network will be created.
When the printer is set to the default value
(Soft-AP mode, SSID: PRINTER_XXXXXX), it will automatically connect.

Network Connection Manual
Ver.1.00
- 17 -
4-4 Initial Wireless LAN Connection (Android Soft AP mode)
1) Select “Wi-Fi”. 2) Select the printer to connect
3) Select “CONNECT”. 4) Wi-Fi communication is available.

Network Connection Manual
Ver.1.00
- 18 -
4-5 Initial Wireless LAN Connection (iOS Soft AP mode)
1) Select “Wi-Fi”. 2) Wi-Fi ON and Select the printer to connect
3) Wi-Fi communication is available

Network Connection Manual
Ver.1.00
- 19 -
4-6 How to change Infrastructure mode
1) Enter the IP address of the printer in the address bar, and the following login window
will pop up. Enter the ID and Password set for the printer, and then click [LOG IN]
Default User Name: admin, Password: password
2) Select “Wireless” to change Wi-Fi mode.

Network Connection Manual
Ver.1.00
- 20 -
3) Select “Infrastructure”, and set SSID, WLAN Security Type.
4) Reboot the Printer.
For changing network setting values using Net configuration tool,
Refer to ‘Net configuration tool manual’.