BIXOLON XM7-30 Instruction manual

Wi-Fi Connection Manual
XM7-30
Ver. 1.00
http://www.bixolon.com

Wi-Fi Connection Manual
Ver.1.00
- 2 -
Table of Contents
Copyright ...................................................................................................................... 3
1. Manual Information ................................................................................................ 4
2. Precautions............................................................................................................... 4
3. How to Connect ........................................................................................................ 5
3-1 Android Soft AP mode (default) ..................................................................................8
3-2 iOS Soft AP mode (default) ..........................................................................................9
3-2 How to change infrastructure mode ........................................................................10
4. Factory Reset .......................................................................................................... 12

Wi-Fi Connection Manual
Ver.1.00
- 3 -
Copyright
© BIXOLON Co., Ltd. All rights reserved.
This user manual and all property of the product are protected under copyright law.
It is strictly prohibited to copy, store, and transmit the whole or any part of the manual
and any property of the product without the prior written approval of BIXOLON Co.,
Ltd.
The information contained herein is designed only for use with this BIXOLON product.
BIXOLON is not responsible for any direct or indirect damages, arising from or
related to use of this information.
• The BIXOLON logo is the registered trademark of BIXOLON Co., Ltd.
•All other brand or product names are trademarks of their respective companies or
organizations.
BIXOLON Co., Ltd. maintains ongoing efforts to enhance and upgrade the functions
and quality of all our products.
In the following, product specifications and/or user manual content may be changed
without prior notice.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn
the printer “OFF”, before you connect or remove the cables on the rear side, in order
to guard the printer against the static electricity. If the printer is damaged by the static
electricity, you should turn the printer “OFF”.

Wi-Fi Connection Manual
Ver.1.00
- 4 -
1. Manual Information
This WLAN manual provides information on the connection of wireless network with
the mobile printer.
2. Precautions
1) The printer has to be within 100m(Out door) from AP(Access point) to connect
WLAN. Although 35m is able to communicate in door, WLAN could be affected by
environment to be shorten.
The printer's LCD shows the connection status of the wireless LAN.
- Indicates that the wireless LAN is connected normally
- Indicates that the WLAN password is wrong
- Indicates that the AP of the set SSID is not nearby
2) The maximum separating distance may be shortened if transmission obstacles, such
as cement walls, are present
3) If a device (such as a microwave oven, wireless LAN, etc.) that uses the same
frequency is present, transmission may be interrupted. Separate the printer and
Bluetooth-enabled device from such interrupting devices by a distance of at least
5m.

Wi-Fi Connection Manual
Ver.1.00
- 5 -
3. How to Connect
WLAN can be configured through the printer’s WLAN interface. Likewise, WLAN can
also be configured though the printer’s Serial/USB interfaces.
(1) Connecting Printer
1) Serial / USB cable
Connect Serial/USB cable to Printer, PC device.
When Serial cable use, baudrate between Device and printer should be the same.
2) WLAN
Connect to the AP (Access Point) configured in Infrastructure mode in order to connect
to the LAN/wireless network
Infrastructure mode
A P

Wi-Fi Connection Manual
Ver.1.00
- 6 -
In order to configure the network between the wireless host device and the printer,
set the printer to Soft AP Mode.
Soft AP mode

Wi-Fi Connection Manual
Ver.1.00
- 7 -
(2) Checking Network Setting
Self-test
While the printer is turned off, turn on the printer while pressing the feed button.
The printer setting values will then be printed.
Power
FEED

Wi-Fi Connection Manual
Ver.1.00
- 8 -
3-1 Android Soft AP mode (default)
1) Select “Wi-Fi”. 2) Select the printer to connect
3) Select “CONNECT”. 4) Wi-Fi communication is available.

Wi-Fi Connection Manual
Ver.1.00
- 9 -
3-2 iOS Soft AP mode (default)
1) Select “Wi-Fi”. 2) Wi-Fi ON and Select the printer to connect
3) Wi-Fi communication is available

Wi-Fi Connection Manual
Ver.1.00
- 10 -
3-2 How to change infrastructure mode
1) Enter the IP address of the printer in the address bar, and the following login window
will pop up. Enter the ID and Password set for the printer, and then click [LOG IN]
(Default User Name: admin, Password: password)
2) Select “Wireless” to change Wi-Fi mode.