BJ Live SHX DIE User manual

BJ-EX28 SHX DIE
User guide
c.Mare de Déu del Coll, 70,Local|08023|Barcelona|Spain|t.+34 93 285 04 37|fax + 34 93 553 56 34| [e-mail] | www.bjliveat.com

BJ-EX28 SHX DIE
Page 2
User guide
BJ –EX28 SHX Die
1_ SHX Die
The SHX Die allows the SHX software content to be accessed by activating the different
functions within the selected scene. Each side of the Die activates a different function.
Please read this guide carefully to familiarize yourself with the SHX Die’s
characteristics before use.
1.1_ Contents
Remove packaging with tools that will not damage or cut the Die. Please dispose of the
packaging responsibly.
If you detect any damaged or missing parts, please contact BJLive! immediately on +34
93 2850437. Any damage caused during transport must be notified to the manufacturer
within three days of delivery.
The SHX Die is comprised of a fabric cover, foam filling, the electronic position sensor
unit and a USB charger.
1.2_ Specifications
Power supply and battery charging: 5V/1000mA USB charger.
Die dimensions: 45 cm x 45 cm x 45 cm.
Electronic unit dimensions: 15cm x 15cm x 15cm.
2400mAh Lithium Polymer battery.

BJ-EX28 SHX CUBE
Page 3
2_Instructions for use
To turn the Die on, unzip the cover, gently
adjusting it to avoid forcing the zipper
slider.
Once open, remove the foam filling that
covers the electronic unit.
The battery should be fully charged before the first
use. See the “Charging the Battery” section below.
Once the battery has been charged, move the
ON/OFF switch to the (| -on) position. Wind up the
charging cable and place it on top of the electronic
unit. Replace the foam filling and zip up the Die,
taking care not to catch the cover in the zipper.
When the Die is switched on, the pre-loaded SHX
software function in the side facing upwards will be
automatically activated.
The SHX software function that is activated on each side of the box is as follows:
Red: function 1
Green: function 2
Yellow: function 3
Blue: function 4
Orange: function 5
Light green: function 6
The selected function will only be activated approximately 3 seconds after the Die has
come to a standstill.
After use, we recommend switching the ON/OFF button to the 0 position to prolong the
battery life.

BJ-EX28 SHX CUBE
Page 4
3_Charging the battery
Switch the ON/OFF button to the (| -on) position in order to charge the
battery.
The electronic unit cable must either be connected to the USB charger provided with the
product or to another similar device: 5V-1000mA.
The charging LED will be red while the battery is being charged. Once the battery is
fully charged, the LED will turn green.
It may take between 4 and 5 hours to charge the battery, depending on it the charge
level. Keep in mind that:
The battery in the electronic unit is a single cell lithium ion/ polymer battery. The
battery will slowly lose its charge even if the Die is not in use. Depending on how
long the product has been stored prior to delivery, the battery may be dead. In
this case, charge the battery fully before use.
Lithium ion/ polymer batteries do not withstand high temperatures. Avoid
exposing the Die to sources of direct heat such as radiators, electric blankets,
heaters etc.
Do not leave the product unattended while charging. This is important in order
to detect any irregularities during the charging process.
While the battery can be charged and discharged numerous times, it will
eventually need to be replaced. It must be replaced when it lasts noticeably less
than usual. Please contact BJLive! for a replacement.
Lithium ion/ polymer batteries do not have a memory effect. Therefore, they can
be charged before they are fully drained. It is advisable to avoid charging the
battery again before it has lost 5% of the charge, in order to reduce the risk of
damage due to unnecessary temperature increases. Brief, repeated charging and
draining may produce inconsistencies between the battery charge level and the
power monitor readings.
To turn the power supply off correctly, disconnect the outlet cable from the
charger/power unit. Lastly, remove the power cable from the device itself.
The inverse is recommended for connecting the power supply.
When disconnecting the charger or an accessory, hold and pull the plug, not the
cable.
Disconnect the charger from the power supply and the device when not in use.
Do not use the charger outdoors.
If the battery or charger appears damaged in any way, please contact BJLive! to
request a check before continuing to use them. Never use damaged chargers or
batteries.

BJ-EX28 SHX CUBE
Page 5
4_Cleaning
Clean the surface of the SHX Die regularly for hygiene reasons and to ensure optimum
visual effects.
It must be disconnected from the power supply before cleaning.
Clean using soapy water and a soft, damp cloth. Do not clean with harsh chemical or
abrasive products. Dry the surface thoroughly.
5_Maintenance
Check that the charging cable is intact and undamaged. Check the cover to prevent any
damage or tearing.
Check that the electronic unit is intact and undamaged. If the unit has been removed
from the foam, replace it as in the image below:
6_Safety precautions
Before throwing the Die, make sure the zipper is completely fastened.
The foam filling presents a risk of suffocation.
Do not throw the Die at people. Its size and weight may cause an injury.
To maintain the Die in optimum conditions, avoid strong impacts and exposure to sharp
or pointed objects.
Do not keep the charger inside the Die.
This product must always be used under adult supervision.

BJ-EX28 SHX CUBE
Page 6