Black & Decker FSM1630 User manual

Australia
New Zealand
www.blackanddecker.com.au
FSM1610-XE

2
B
A
D
C
F
E

3
H
G
I

4
ENGLISH (Original instructions)
Intended use
Your Black & Decker steam mop has been designed for
sanitising and cleaning sealed hardwood, sealed laminate,
linoleum, vinyl, ceramic tile, stone and marble oors and for
refreshing carpets. This appliance is intended for indoor
household use only.
Safety instructions
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, re and/or serious injury.
@Warning! When using mains-powered appli-
ances, basic safety precautions, including the
following, should always be followed to reduce
the risk of re, electric shock, personal injury and
material damage.
uRead all of this manual carefully before using the appli-
ance.
uThe intended use is described in this manual. The use of
any accessory or attachment or the performance of any
operation with this appliance other than those recom-
mended in this instruction manual may present a risk of
personal injury.
uRetain this manual for future reference.
Using your appliance
uDo not direct steam at people, animals, electrical appli-
ances or electrical outlets.
uDo not expose to rain.
uDo not immerse the appliance in water.
uDo not leave the appliance unattended.
uDo not leave the appliance connected to an electrical
outlet when not in use.
uNever pull the power lead to disconnect the appliance
from the socket. Keep the appliance lead away from heat,
oil and sharp edges.
uDo not handle steam cleaner with wet hands.
uDo not pull or carry by cord, use cord as a handle, close
door on cord, pull cord around sharp corners or expose
cord to heated surfaces.
uDo not use appliance in an enclosed space lled with
vapour given off by oil-base paint thinner, some moth-
proong substances, ammable dust, or other explosive
or toxic vapours.
uCheck the type of oor with the manufacturer.
uDo not use on leather, wax polished furniture or oors,
synthetic fabrics, velvet or other delicate, steam-sensitive
materials.
@Warning! Do not use on unsealed wood or
unsealed laminate oors. On surfaces that have
been treated with wax or some no wax oors, the
sheen may be removed by the heat and steam
action. It is always recommended to test an
isolated area of the surface to be cleaned before
proceeding. We also recommend that you check
the use and care instructions from the oor
manufacturer.
uNever put descaling, aromatic, alcoholic or detergent
products into the steam cleaner, as this may damage it or
make it unsafe for use.
uIf the home circuit breaker activates while using the steam
function, discontinue product use immediately and contact
the customer support centre. (Beware of the risk of electri-
cal shock.)
uThe appliance emits very hot steam to sanitize the area of
use. This means that the steam head, cleaning pads and
carpet attachment get very hot during use.
uCaution! Always wear suitable shoes when using your
steam mop and when changing the accessories on your
steam mop. Do not wear slippers or open toed footwear.
uThe lid may become hot during use.
uSteam may escape from the appliance during use.
uCare should be taken when using this appliance. DO NOT
touch any parts which may become hot during use.
uSwitch the appliance off and return the handle to the
upright position before removing the water tank.
uFor oor use only; do not use the unit upside down. This
appliance is intended for indoor household use only.
After use
uUnplug the appliance and allow to cool before cleaning.
uWhen not in use, the appliance should be stored in a dry
place.
uChildren should not have access to stored appliances.
Inspection and repairs
uUnplug the appliance and allow to cool before performing
any maintenance or repairs.
uBefore use, check the appliance for damaged or defective
parts. Check for breakage of parts, damage to switches
and any other conditions that may affect its operation.
uRegularly check the power lead for damage.
uDo not use the appliance if any part is damaged or defec-
tive.
uHave any damaged or defective parts repaired or replaced
by an authorized repair agent.
uNever attempt to remove or replace any parts other than
those specied in this manual.

5
ENGLISH
(Original instructions)
Safety of others
uThis appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing the use of the appliance by a person responsible for
their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any moving parts.
uInjuries caused by touching any hot parts.
uInjuries caused when changing any parts or accessories.
uInjuries caused by prolonged use of the appliance. When
using any appliance for prolonged periods ensure you
take regular breaks.
Electrical safety
@Warning! This product must be earthed.
Always check that the power supply corre-
sponds to the voltage on the rating plate.
Power plugs must match the outlet. Never modify the plug in
any way. Unmodied plugs and matching outlets will reduce
risk of electric shock.
uIf the supply cord is damaged, it must be replaced by
the manufacturer or an authorised Black & Decker
Service Centre in order to avoid a hazard.
Extension cables & Class 1 product
uA 3-core cable must be used as your appliance is
earthed and of Class 1 construction.
uUp to 30m (100 ft) can be used without loss of power.
Labels on the appliance
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Warning! Danger of scalding.
Features
This appliance includes some or all of the following features.
1. ON/Off switch
2. SmartselectTM dial
3. Removable water tank
4. Handle
5. Steam head
6. Steam head cleaning pad
7. Resting mat
8. Bottom cable tidy hook
9. Top cable tidy hook
10. Cable management clip
11. Carpet Glider
Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
uSlide the bottom end of the handle (4) into the top end of
the steam mop body (12) until it clicks into place.
Attaching the steam head (Fig. B)
uSlide the bottom end of the steam mop body (12) onto the
steam head (5) until it clicks into place.
uThe steam head can be removed from the Steam mop
body by pressing the steam head release button (13) and
pulling the steam mop body (12) off the steam head (5).
Attaching the water jug (Fig. C)
uClip the water jug (3) onto the handle (4).
uSlide the water jug (3) down into the Steam mop body
(12), ensure that the water jug is rmly seated.
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your Black &
Decker dealer:- (cat. no. FSMP20-XE).
uPlace a cleaning pad (6) on the oor with the ‘hook & loop’
side facing up.
uLightly press the steam mop down onto the cleaning pad
(6).
Caution! Always place your steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.

6
ENGLISH (Original instructions)
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
uReturn the handle (4) to the upright position and turn the
steam mop ‘OFF’.
uPlace the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
uPlace the front of your shoe onto the cleaning pad removal
tab (14) and press down rmly.
uLift the steam mop up off the cleaning pad.
Caution! Always place the steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Attaching the carpet glider (Fig. F)
uPlace carpet glider on the oor.
uLightly press the steam mop down onto the carpet glider
(11) until it clicks into place.
Caution! Always place the steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. F)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
uReturn the handle (4) to the upright position and turn the
steam mop ‘OFF’.
uPlace the steam mop on the resting mat and wait until it
cools down. (approximately ve minutes)
uPlace the front of your shoe onto the carpet glider removal
tab (15) and press down rmly.
uLift the steam mop up off the carpet glider (9).
Caution! Always place the steam mop on the resting mat (7)
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. G)
The watertank on your steam mop is removable for convi-
enient and easy lling.
This Steam Mop incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
uRemove the water tank (3).
uOpen the ller cap (16) by lifting it up.
uFill the water tank (3) with water.
Warning! Your water tank has a 0.5 litre capacity. Do not over
ll the tank.
uRe-t the ller cap (14).
uRe-t the water tank (3).
Note: Ensure the ller cap is rmly secured.
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro bre
pad tted and a continuous run time of 90 seconds.
Switching on and off
uTo switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is rst turned on the water res-
ervoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
uTo switch the appliance off, press the ON/OFF button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (7) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
SmartselectTM Technology
This steam mop is tted with an SmartselectTM dial (2) which
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning opera-
tion.
Using the SmartselectTM dial (2), choose from one of the fol-
lowing applications:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Hints for optimum use

7
ENGLISH
(Original instructions)
General
Caution! Never use the steam mop without rst attaching a
cleaning pad.
uDuring use you can use the cable mamagement clip (10)
to keep your cable out of the way of the work area..
uAlways vacuum or sweep the oor before using the steam
mop.
uThe easiest way to use the machine is to tilt the handle to
a 45˚ angle and clean slowly, covering a small area at a
time.
uDo not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum oors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam cleaning
uPlace a cleaning pad (6) on the oor with the ‘hook & loop’
side facing up.
uRaise the steam mop off the resting mat (7) and lightly
press it down onto the cleaning pad (6).
uPlace the steam mop on the resting mat.
uConnect the steam mop to the mains.
uTurn the SmartselectTM dial (2) to the required setting.
uPress the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
uPulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
uIt takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
uPush and pull the steam mop slowly across the oor to
thoroughly steam clean each section.
Note: During use you may turn off the steam pump by return-
ing the handle to the upright position, this convenient feature
will allow you to place the steam mop on the resting mat for
a short time so that you may move items of furniture, then
continue cleaning without the need to switch the appliance off.
uWhen you have nished using the steam mop, return the
handle (4) to the upright position and turn it ‘OFF’, place it
on the resting mat (7) and wait until the steam mop cools
down. (approximately ve minutes)
Caution! It is important to monitor the water level in the water
tank. To rell the water tank and continue to sanitise/clean,
return the handle (4) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet,
remove and rell the water tank (3).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (7) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
After use (Fig. H & I)
uReturn the handle (4) to the upright position and turn the
steam mop ‘OFF’,
uPlace the steam mop on the resting mat (7) and wait until
the steam mop cools down. (approximately ve minutes)
uUnplug the steam mop from the electrical wall outlet.
uEmpty the water tank (3).
uRemove the cleaning pad (6) and wash it ready for next
use. (Take care to follow the wash care instructions
printed on the cleaning pad).
uWrap the supply cable around the cable tidy hooks (8 &
9).
Note: The top cable tidy hook (9) rotates to easily release the
cable ready for next use.
uClip the supply cable onto itself using the cable tidy clip
(17) close to the plug.
uPlace steam mop on the resting mat (7) for storage.
Note: With the handle (4) in the upright position, the cable
neatly wrapped around the cable tidy hooks (8 & 9) and
secured with the cable tidy clip (17) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(18) built into the hand grip (19) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.
Maintenance and cleaning
Your Black & Decker corded appliance has been designed to
operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper appliance care and regular cleaning.
Warning! Before performing any maintenance or cleaning on
corded appliances switch off and unplug the appliance.
uWipe your appliance over using a soft damp cloth.
uFor stubborn marks you can use a mild solution of soap
and water to dampen your cloth.
Care of the cleaning pads
Wash care instructions - No fabric conditioner - Allow to dry
fully before re-use.
Caution! Follow the cleaning instructions printed on the label
of the cleaning pad.
Protecting the environment

8
ENGLISH (Original instructions)
ZSeparate collection. This product must not be disposed of with normal household waste.
Should you nd one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
zSeparate collection of used products and packaging allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker ofce at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
FSM1610-XE
(Type 1)
Voltage Vac
230
Power W
1600
Tank capacity ml
460
Weight kg 2.7
90591388 01/2013
Australia & New Zealand
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia
Tel.[phone] (Aust) or Tel. [phone] (NZ)