
10
ENGLISH (Original instructions)
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
uReturn the steam mop to the upright position and turn the
steam mop 'OFF'.
uWait until the steam mop cools down (approximately 5
minutes).
uLift the steam mop away from the cleaning pad freeing it
from the velcro fastening by putting weight on the cleaning
pad removal tab (11).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Filling the water tank (Fig. D)
Note! Fill the water tank with clean tap water (Do not use any
additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
uOpen the ller cap (4) by ipping it up.
uFill the water tank with water (Do not use any additives or
chemicals).
Warning! When lling, maintain in a horizontal position.
Warning! Your water tank has a 0.5 litre capacity. Do not over
ll the tank.
uClose the ller cap (4).
Note! Ensure the ller cap is rmly secured.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro bre pads tted and a continuous run time
of 90 seconds.
Switching on and off (Fig. F)
uTo switch the appliance on, press the ON/Off switch (1).
It takes approximately 20 seconds for the steam mop to
heat up.
uTo switch the appliance off, press the ON/Off switch (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Note! When rst lled or after running dry, it can take up to 45
seconds for steam to be produced.
AutoselectTM Technology (Fig. E)
This steam mop is tted with an AutoselectTM dial (2) which
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning
operation.
Using AutoselectTM, choose from one of the following
applications by turning the AutoselectTM dial (2) until the
required setting is selected.
Setting Mop Hand held
Wood/Laminate Low steam ow
Tiles/Vinyl Medium steam ow
Stone/Marble High steam ow
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Attaching the hose and accessories to the
hand held steam cleaner
Warning! Inspect the seal between the connection point on
the hand held steam cleaner and the steam hose (12) before
each use. If the seal malfunctions or is damaged, please
contact your nearest authorised repair agent. Do not use the
appliance.
Attaching the hose (Fig. H)
uPress the steam hose release button (17) on the steam
hose (12).
uConnect the steam hose (12) to the hand held steam
cleaner and release the steam hose release button (17)
making sure it clicks into place.
Important! Ensure that the steam hose (12) is securely
connected to the hand held steam cleaner. If steam escapes
from the joint, the hose is incorrectly tted. Switch off, allow
the unit to cool then remove and ret the hose.
Warning! The unit should be switched off before the hose is
tted.
Attaching accessories (Fig I)
uAlign the lugs on the steam nozzle (12) with the recesses
on the accessory.
uPress the accessory onto the steam nozzle and twist
anticlockwise until the accessory clicks into place.
Important! All accessories must be attached to the steam
hose (12) for use.
Removing the hose and accessories
Warning! The steam hose (12), Steam nozzle and
accessories become hot during use.