Black Horse Model Focke-Wulf FW190A User manual

SPECIFICATION


Wingspan : 1,780 mm 70.08 in.


Length : 1,520 mm 59.84 in.


Weight : 4.8 kg 10.56 Lbs.


Radio : 06 channels.


Servo : 09 servos.


Engine : 120 4stroke
Instruction Manual book
MadeinVietnam.

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
2
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your Focke-Wulf FW190A. Use the parts listing
below to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalso beable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
Toavoid scratching yournew airplane,donot
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the
aircraftand toprotect thetable. Keepa couple
of jars or bowls handy to hold the small parts
after you open the bag.
Pleasetrialfitalltheparts. Makesureyouhave
the correct parts and that they fit and are
alignedproperly beforegluing!Thiswillassure
proper assembly. Focke-Wulf FW190AARF is
handmadefromnaturalmaterials,everyplane
is unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the
following: paint thinner, C/A glue accelerator,
C/A glue debonder and acetone. Do not let
these chemicals come in contact with the
colors on the covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
Caution: this model is not a toy!
Ifyouare abeginner tothis typeofpowered model,please askan experiencedmodelflyer forhelp
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhaveto carryout isimportantandmust bedone carefully.The modelwill only bestrong andfly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
REPLACEMENT LARGE PARTS
B. Wing panel. C. Fuselage. D. Horizon stabilizer.
E. Vertical stabilizer.
A.Cowling.
F. Aluminium wing dihedral brace.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning
propeller.
A
B
C
B
F
D
E

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
4
3.Wheels.
12.Valvecontrol.
10.Air line sets.
8.Valveoneway.
14.3 way connector.
5. Plastic for tail gear.
2.Air retract main gear.
13.Air tank.
4. Tail gear set.
6. Battery tray.
Top side
 1) Install the rubber grommets and brass
eyelets onto the aileron servos.
1.INSTALLING THE AILERON SERVOS.
11.Plastic parts for pushrod.
I. AILERON.
Bottom side
REPLACEMENT SMALL PARTS
1.Door mounting wheel.
7. Fuel tank.
9.Spinner.
15.Plastic -engine mount.
8.
1.
2.
2. 3.
4. 5.
7.
9. 10. 11.
6.
12. 13. 14.
15.
4 x 30mm
3 x 15mm

5
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
C/A glue.
C/A glue.
C/A glue.
Aileron
Flap Bottom side
C/A glue.
C/A glue.
Repeat the procedure for the other
wing half.
C/A glue.
C/A glue.
C/A glue.
Bottom side
Aileron
Flap

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
6
Thread
Electric wire
2.INSTALLING THE AILERON CONTROL HORN.
Secure.
4)Drill 1,6mmpilot holesthroughtheblock
of wood for each of the four mounting screws
provided with the servo.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
M3 lock nut.
3mm x 50mm.
Nilon control clasp.
2x10mm.
2)Using amodeling knife,remove thecov-
ering at possition show below.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
Servo tray.
Removecovering

7
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
Repeat the procedure for the other wing
half.
Control horn
of the aileron
Installing the aileron linkages as pictures
below.
3.INSTALLING THE AILERON
LINKAGES.
C/A glue.
II. FLAP.
1.INSTALLING THE FLAP SERVOS.
thread
M2locknut
65mm

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
8
Installing the aileron linkages as pictures
below.
Flap control
horn.
2x10mm.
Electric
way
Secure.
2. INSTALLING THE FLAP CONTROL HORN.
3mm x 30mm.
Nilon control clasp.
3.INSTALLING THE FLAP
LINKAGES.

9
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
Repeat the procedure for the other wing
half.
C/Aglue
INSTALLING AIR RETRACTABLE
LANDING GEAR.
3 x 15mm
M2locknut
65mm
Secure
3 x 15mm
3x10mm
3 x 15mm
3x16mm
1.
2. 2.
3. 3.
10.

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
10
BH 87-AR

11
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
Secure
Lock nut
3 x 10 mm
3 x 16 mm
Secure.

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
12
4 x 35mm
Secure
Drilla hole
3.5mmdiameter
Drilla hole
3.5mmdiameter
Locate the aluminium wing dihe-
dral brace.
WINGATTACHMENT.
*** Test fit the aluminium tube dihedral brace
into each wing haft. The brace should slide in
easily. If not, use 220 grit sand around the
edges and ends of the brace until it fits prop-
erly.
Drill a hole
3.5mm diameter
Bottom side.
Lock.
Lock.
Repeat the procedure for the other wing
half.

13
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
FUSELAGE-CANOPYAND PILOT.
C/Aglue
C/Aglue
Epoxyglue.

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
14
INSTALLING THE STOPPER ASSEMBLY
1) The stopper has been pre-assembled
at the factory.
2) Using a modeling knife, cut one length
ofsilicon fuelline(thelengthofsiliconfuel line
iscalculatedbyhowtheweightedclunkshould
restabout 8mmaway fromtherearofthetank
andmove freelyinside thetank). Connectone
FUEL TANK.
end of the line to the weighted clunk and the
otherend tothenylonpickuptubein thestop-
per.
3) Carefully bend the second nylon tube
up at a 45 degree angle (using a cigarette
lighter). This tube will be the vent tube to the
muffler.
4) Carefullybend thethirdnylon tubedown
ata 45degreeangle (usingacigarettelighter).
This tubewill bevent tubeto thefuelingvalve.
See pictures below:
INSTALLING THE ENGINE MOUNT.
Drill a hole
2mmdiameter
C/Aglue
4x30mm
4x30mm

15
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
5) Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using
amodeling knife. Ifflashing is present, make
sure none of it falls into the tank.
6) When satisfied with the alignment of
thestopperassemblytightenthe3mmx20mm
machine screw until the rubber stopper ex-
pandsand sealsthetank opening.Do notover
tighten the assembly as this could cause the
tank to split.
the stopper.
8) Feed three lines through the fuel tank
compartment and through the pre-drilled hole
in the firewall. Pull the lines out from behind
the engine, while guiding the fuel tank into
place. Push the fuel tank as far forward as
possible,the frontofthetankshould justabout
touch the back of the firewall.
Blow through one of the lines to ensure
the fuel lines have not become kinked inside
the fuel tank compartment. Air should flow
througheasily.
9) To secure thefuel tankinplace, applya
bead of silicon sealer to the forward area of
thetank, whereit exitsthefuselage behindthe
enginemountingbox andtotherearofthetank
at the forward bulkhead.
Vent tube Fuel pick- up tube
Fuelfilltube
When the stopper assembly is installed in the
tank, the top of the vent tube should rest just
belowthe topsurfaceof thetank. Itshould not
touch the top of the tank.
(Silicon tube not included)
Silicon tube.
7) Using a modeling knife, cut 3 lengths of
fuel line 150mm long. Connect 2 lines to the 2
vent tubes and 1 line to the fuel pickup tube in
Do not secure the tank into place perma-
nently until after balancing the airplane. You
may need to remove the tank to mount the
battery in the fuel tank compartment

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
16
Drill a hole
4mm diameter.
INSTALLING THE ENGINE.
Locate the long piece of wire used for the
throttlepushrod. Oneendofthewire hasbeen
pre-bend in to a “Z” bend at the factory. This
“Z” bend should be inserted into the throttle
armofthe enginewhentheengine isfittedonto
theengine mount.Fittheengineto theengine
mount using the screws provided.
150mm
Markpoint

17
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
1. Slide the fiberglass cowl over the en-
gineand lineup thebackedgeofthe cowlwith
the marks you made on the fuselage.
2. While keeping the back edge of the
cowl flush with the marks, align the front of
thecowlwiththecrankshaftoftheengine. The
front of the cowl should be positioned so the
crankshaft is in nearly the middle of the cowl
opening. Hold the cowl firmly in place using
pieces of masking tape.
3. Slide the cowl back over the engine
andsecure itin placeusing fourwood screws.
See picture below.
4. Installthemufflerandmufflerextension
onto the engine and make the cutout in the
cowl for muffler clearance. Connect the fuel
and pressure lines to the carburetor, muffler
andfuel fillervalve.
Trim and cut
Bottom side
COWLING.
Left side
Top side
Secure
4 x 30mm
Right side
Bottom side

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
18
3 x 12mm
Left side
Machine screw.
INSTALLING THE SPINNER.
Installthe spinnerbackplate,propellerand
spinner cone. The spinner cone is held in
place using two 3mm x 12mm wood screws.
Front view.
Trim and cut
Right side

19
Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
See pictures below:
HORIZONTALSTABILIZER.
Elevator servo
Cut.
SERVO INSTALLATION.
ELEVATOR INSTALLATION.
2. Mount the servo to the tray using the
mountingscrews providedwithyourradiosys-
tem.
1. Install the rubber grommets and brass
colletsintothe elevatorservo.Test fittheservo
into the servo tray.
Install one adjustable metal connector
through the third hole out from the center of
one servo arm, enlarge the hole in the servo
arm using a 2mm drill bit to accommodate the
servo connector. Remove the excess mate-
rial from the arm.
INSTALLING THE THROTTLE PUSHROD.
After installing the adjustable metal con-
nector apply a small drop of thin C/A to
the bottom nut. This will prevent the con-
nector from loosening during flight.
Connector.
Servo arm.
Throttle servo
Secure

Focke-Wulf FW190A-Item code:BH87 INSTRUCTION MANUAL.
20
C/Aglue
C/Aglue
C/Aglue
C/Aglue
Check to mark sure the wing and stabi-
lizer are paralell. If they are not, lightly sand
theopening inthefuselageforthe stabilizer
until the stabilizer is paralell to the wing.
C/Aglue
1. Draw a center line onto the horizontal
stabilizer. Then slide the horizontal into the
fuselage.
Centerline