Blancett B3000 User manual

Compact Digital Flow Monitor
B3000
DSY-PM-00022-EN-07 (August 2015) User Manual
2
1
J1
S1
Menu
S4
Enter
S3
Up
S2
Down
COM 12
12 1
C
L
A
S
S
I
F
I
E
D

Compact Digital Flow Monitor, B3000
DSY-PM-00022-EN-07Page ii August 2015
CONTENTS
Scope of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Terminology and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting the B3000 to a Frequency Output Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Solar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating The Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programming Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming Using Frequency Output Turbine Flow Meters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Gas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Return to Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Default K-Factor Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Battery Replacement (B30A/B/X/Z only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
NEMA 4X Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Explosion Proof Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Menu Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
K-Factors Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Calculating K-factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Explosion-Proof Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Modbus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Modbus Register / Word Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
C Source Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Part Number Construction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Meter Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Remote Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Explosion Proof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Swivel Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Scope of This Manual
DSY-PM-00022-EN-07 Page 3August 2015
SCOPE OF THIS MANUAL
This manual is intended to help you get the B3000 flow monitor up and running quickly.
MPORTANTI
Read this manual carefully before attempting any installation or operation. Keep the manual accessible for future reference.
UNPACKING AND INSPECTION
Upon opening the shipping container, visually inspect the product and applicable accessories for any physical damage such
as scratches, loose or broken parts, or any other sign of damage that may have occurred during shipment.
OTE:N If damage is found, request an inspection by the carrier’s agent within 48 hours of delivery and file a claim with the
carrier. A claim for equipment damage in transit is the sole responsibility of the purchaser.
SAFETY
Terminology and Symbols
Indicates a hazardous situation, which, if not avoided, is estimated to be capable of causing death or
serious personal injury.
Indicates a hazardous situation, which, if not avoided, could result in severe personal injury or death.
Indicates a hazardous situation, which, if not avoided, is estimated to be capable of causing minor or
moderate personal injury or damage to property.
Considerations
The installation of the B3000 flow monitor must comply with all applicable federal, state, and local rules, regulations,
and codes.
EXPLOSION HAZARD  SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
AVERTISSMENT
RISQUE D’EXPLOSION  LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CEMATÉRIEL INACCCEPTABLE POUR LES
EMPLACEMENTS DE CLASSE I, DIVISION 2.
DO NOT CONNECT OR DISCONNECT EITHER POWER OR OUTPUTS UNLESS THE AREA IS KNOWN TO BE NON
HAZARDOUS.
AVERTISSMENT
RISQUE D’EXPLOSION. NE PAS DÉBRANCHER TANT QUE LE CIRCUIT EST SOUSTENSION, À MOINS QU’LL NE S’AGISSE
D’UN EMPLACEMENT NON DANGEREUX.
MPORTANTI
Not following instructions properly may impair safety of equipment and/or personnel.
Electrical Symbols
Function Direct
Current
Alternating
Current
Earth
(Ground)
Protective
Ground
Chassis
Ground
Symbol

Introduction
DSY-PM-00022-EN-07Page 4 August 2015
INTRODUCTION
The B3000 flow monitor incorporates state-of-the-art, digital signal processing technology, designed to provide exceptional
flexibility at a very affordable price. Though designed for use with Blancett flow sensors, this monitor can be used with almost
any flow sensor producing a low amplitude AC output or contact closure signal.
2
1
J1
S1
Menu
S4
Enter
S3
Up
S2
Down
COM 12
12 1
Figure 1: B3000 Flow monitor (NEMA 4X) Figure 2: B3000 Flow monitor (Ex-Proof)
This monitor can accept low-level frequency input signals typically found in turbine flow sensors. The output signal for
these types of sensors is a frequency proportional to the rate of flow. The B3000 monitor uses the frequency information
to calculate flow rate and total flow. Through the use of the programming buttons, you can select rate units, total units and
unit time intervals among other functions. All B3000 flow monitors come pre-configured from the factory, when ordered
with a Blancett flow sensor. If required, the monitor can easily be re-configured in the field. Finally, you can choose between
simultaneously showing rate and total, or alternating between rate and grand total.
The monitor is available in two different levels of functionality and two packaging options. The base model provides all
the functions necessary for the most common flow metering applications. The advanced version adds communications
capabilities over an RS485 bus using Modbus RTU and control outputs. The B3000 monitor can be powered using loop,
battery or solar power.
Packaging options include a polycarbonate, NEMA 4X version and an aluminum explosion proof enclosure.

Installation
DSY-PM-00022-EN-07 Page 5August 2015
INSTALLATION
Connecting the B3000 to a Frequency Output Device
Most turbine flow sensors produce a frequency output that is directly proportional to the volumetric flow through the sensor.
There are, however, different output waveforms that can be presented to the display device depending on the transducer that
converts the mechanical motion of the turbine into an electrical signal.
The B3000 monitor has two jumpers for setting the type of signal and the minimum amplitude of the signal that it accepts.
First, establish the type of output provided by the flow sensor. The outputs almost always fall into one of two types.
• Type 1 is the unaltered frequency signal coming from an un-amplified magnetic pickup. This signal is normally a sine wave
in appearance, and the amplitude of the waveform varies with the flow. Small turbines have comparatively small rotating
masses so they produce a smaller amplitude waveform and higher frequencies than larger turbine sensors.
• Type 2 is the frequency signal from the transducer is amplified, wave shaped or both, to produce a waveform of a specified
type and amplitude. Most amplified transducers output a square wave shape at one of many standard amplitudes. For
example a popular amplified output is a 10V DC square wave.
If the flow sensors output signal is type 1, you must also determine the minimum amplitude of the frequency output. The
B3000 monitor has a high or low signal sensitivity setting. Use the high signal sensitivity (30 mV) with low amplitude (usually
small) turbine flow sensors. Use the low signal sensitivity setting (60 mV) for larger turbines and amplified transducers (see
Figure 3 and Figure 4).
OTE:N Use the high signal sensitivity setting where the minimum signal amplitude is below 60 mV. Setting the sensitivity
lower than necessary may allow of noise interference.
JP1
JP2
JP3
Input Total Pulse Signal
TB1
Mag
Pulse
Iso
OC
Low
High
Input Waveform Selection
(Magnetic Pickup Selection Shown)
Input Signal Level Selection
(Low Signal Sensitivity (60 mV) Selection Shown)
Freq. In
+
–
Gnd
JP1
Input
MagPulse
JP2
TB2
TB1
P1
Signal
LowHigh
P1
Input Waveform Selection
(Magnetic Pickup Selection Shown)
Input Signal Level Selection
(Low Signal Sensitivity (60 mV) Selection Shown)
Figure 3: Input jumper settings (NEMA 4X) Figure 4: Input jumper settings (Ex-Proof)
When the type of waveform and input signal level (amplitude) are determined, set the jumpers on the B3000 monitor
circuit board.
For typical variable reluctance magnetic pickups, set the waveform selection jumper for Mag. Determine the setting for the
input level by looking at the magnetic pickup specifications. If the minimum amplitude at the minimum rated flow is greater
than 60 mV, use the low signal sensitivity jumper position (see Figure 3 and Figure 4).
If the minimum signal level is below 60 mV, use the high signal sensitivity jumper position.

Installation
DSY-PM-00022-EN-07Page 6 August 2015
JP1
JP2
JP3
Input Total Pulse Signal
P1
Freq. In
4-20mA
Iso TotalPluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
TotalR eset
OC TotalPluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
Mag
Pulse
JP1
Input
Freq. In
4-20mA
Iso Total Pluse
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
P2 3.6Vdc
Battery
JP3
Total Pulse
ISO OC
JP1
Input
MagPulse
JP2
TB2
TB1
P1
Signal
LowHigh
P1
JP1
Input
MagPulse
Figure 5: Typical magnetic pickup connection (NEMA 4X) Figure 6: Typical magnetic pickup connection (Ex-Proof)
For amplified input signals the input jumper should be set to Pulse and the signal jumper set to Low
(see Figure 7 and Figure 8).
OTE:N Amplified magnetic pickups require an external power source. The B3000 does not supply power to an
amplified pickup.
JP1
JP2
JP3
Input Total Pulse Signal
P1
Freq.I n
4-20mA
IsoTotal Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
TotalReset
OCTotal Pluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
POWER
SUPPLY
Mag
Pulse
JP1
Input
Freq. In
4-20mA
Iso Total Pluse
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
P2 3.6Vdc
Battery
JP3
Total Pulse
ISO OC
JP1
Input
MagPulse
JP2
TB2
TB1
P1
Signal
LowHigh
P1
POWER
SUPPLY
JP1
Input
MagPulse
Figure 7: Typical amplified pickup connection (NEMA 4X) Figure 8: Typical amplified pickup connection (Ex-Proof)

Power Connections
DSY-PM-00022-EN-07 Page 7August 2015
POWER CONNECTIONS
Standard
The power supply used in the B30A/B/X/Z is an internal lithium 3.6V DC D cell that will power the monitor for about six years
when no outputs are used. The monitor can also get power from a 4…20 mA current loop (see Figure 9 and Figure 10). If the
current loop is used a sensing circuit within the monitor detects the presence of the current loop and disconnects the battery
from the circuit. The B30S uses solar power only.
JP1
JP2
JP3
Input Total Pulse Signal
P1
Freq. In
4-20mA
Iso Total Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
4…20 mA
Current Loop
(10…28V DC)
Load
10…28V DC
Freq. In
4-20mA
Iso Total Pluse
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
P2 3.6Vdc
Battery
JP3
Total Pulse
ISO OC
JP1
Input
MagPulse
JP2
TB2
TB1
P1
Signal
LowHigh
P1
4…20 mA
Current Loop
(10…28V DC)
Load
10…28V DC
Figure 9: Loop power connections (NEMA 4X) Figure 10: Loop power connections (Ex-Proof)
CAUTION
GROUNDING FOR THE EXPLOSION PROOF ENCLOSURE IS NECESSARY. THE EXPLOSION PROOF ENCLOSURE IS
PROVIDED WITH A GROUNDING SCREW ON THE INSIDE OF THE ENCLOSURE. THE CONDUCTOR USED FOR GROUNDING
MUST BE OF A WIRE GAGE EQUAL TO OR GREATER THAN THE SIGNAL WIRES BEING USED. SEE FIGURE 11.
The explosion proof enclosure is provided with a grounding screw on the inside of the enclosure. The conductor used for
grounding must be of a wire gage equal to or greater than the signal wires being used.
To Earth Ground
Grounding Screw
Figure 11: Required grounding for Ex-proof enclosure

Operating The Monitor
DSY-PM-00022-EN-07Page 8 August 2015
Solar
A solar cell mounted on the top of the monitor in the B30S charges an internal 3.6V DC nickel-cadmium battery that powers
the monitor. A fully charged battery powers the monitor for approximately 30 days. The solar powered B3000 has a single
totalizing pulse output and cannot be powered by a 4…20 mA loop.
2
1
Solar Cell
Figure 12: Solar powered B3000
OPERATING THE MONITOR
The monitor has three modes of operation referred to as the Run, Programming, and Extended Programming modes.
2
1Battery
Indicator
Alarm
Activation
Rate
Units
Totalizer
Units
Totalizer
Multiplier
Total
Rate
Communications
Indicator
Figure 13: Display annunciators
To access the program mode, momentarily press and then release MENU until the first programming screen is displayed. The
extended programming mode is entered by pressing and holding MENU until the first programming option appears. After
programming the display with the necessary information, a lock out feature is available to prevent unauthorized access or
changing of the meter’s setup parameters.

Operating The Monitor
DSY-PM-00022-EN-07 Page 9August 2015
Programming Mode
COM 12
J1
S1
Menu
S4
Enter
S3
Up
S2
Down
COM 12
12 1
Figure 14: Keypad detail
Buttons
MENU – Switches between normal running and programming modes.
UP Arrow (▲) – In programming mode scrolls forward through the parameter choices and increments
numeric variables.
RIGHT Arrow (►) – In programming mode scrolls backward through the parameter choices and moves the active
digit to the right.
ENTER – Used to save programming information, advance to the next programming parameter, and in the
reset process.
TOTAL FLOW RESET – This touch sensor button allows the total to be reset without opening up the case. This button
pertains to the explosion proof version only.
OTE:N The“through the glass”touch sensor button is currently under development in the explosion proof version
of the B3000.
Special Functions
MENU + ENTER – Simultaneously press and hold to reset the current totalizer.
MENU - Press and hold menu for three seconds to enter extended programming mode.
UP Arrow (▲) + Right Arrow (►) – Simultaneously press and hold to show the firmware version number, then the
grand total.
UP Arrow (▲) – In run mode increases display contrast.
RIGHT Arrow (►) – In run mode decreases display contrast.
Modes
RUN – Normal operating mode.
PROGRAM – Used to program variables into the display.
EXTENDED PROGRAM –Used to program advanced variables into the display.
TEST –Used as a diagnostic tool to show input frequency and totalizer counts.
If your monitor was ordered with a Blancett flow meter, the two components ship from the factory configured as a set. If the
monitor is a replacement, the turbine’s K-factor changed, or the monitor is used with some other pulse generating device;
programming is necessary.
Programming Using Frequency Output Turbine Flow Meters
Each Blancett turbine flow meter is shipped with either a K-factor value or frequency data. If frequency data is provided, the
data must be converted to a K-factor before programming the monitor. K-factor information, when supplied, can usually be
found on the neck of the flow meter or stamped on the flow meter body. The K-factor represents the number of pulses per
unit of volume (see K-Factors Explained on page 29). The K-factor is required to program the monitor.

Programming
DSY-PM-00022-EN-07Page 10 August 2015
Essentials
The B3000 monitor is engineered to provide several levels of programming tailored to the needs of the user. The first or
standard level provides access to the most commonly used setup parameters bypassing the more advanced settings. The first
level programming is entered by pressing and holding MENU for about one second.
The second level or extended settings are accessed by pressing and holding MENU until the extended programming
menu starts.
With the standard and solar liquid monitors there is a third level. For the most basic unit setup choices the B3000 monitor
employes a simple and advanced setup option accessed through the Rate SU parameter. If Simple is selected the rate and total
choices are reduced to the five most common combinations avoiding the need to make unit and interval choices.
Liquid Meters Standard Solar Advanced I/O
Basic Functions Press MENU for about one second and then release.
Extended Functions Press and hold MENU until the extended programming menu starts.
Simple Setup Select Rate SU in the extended functions and choose Simple.Not Applicable
Advanced Setup Select Rate SU in the extended functions and choose Advanced.
Table 1: Display mode selection information
Enter Programming Mode
The programming modes are accessed by pressing MENU for basic functions. Extended functions are accessed by pressing
and holding MENU until the first programming parameter appears.
2
1Battery
Indicator
Units
Indicator
Totalizer
Units
Totalizer
Multiplier
Numeric
Values
Function
Figure 15: Programming mode display
PROGRAMMING
The following programming assumes the meter is set for liquid. Parameters for gaseous fluids can be found in
Gas on page 19.
OTE:N All of the following parameters appear in Extended Programming mode. Parameters with an asterisk (*) appear in
Programming mode as well.
Liquid
Select Fluid*
At the Fluid prompt, press ENTER to view the current fluid type. If the current fluid type is correct, press ENTER to advance to
the next parameter. To change the fluid type, press UP or RIGHT to switch between Liquid or Gas. Press ENTER to save and
advance to the Meter parameter.
OTE:N The fluid selection choice affects which menu choices are available. Consult the full Menu Maps on page 23
for details.
Select Meter Size*
At the Meter prompt, press ENTER to display the current meter size. If the current meter size is correct, press ENTER to
advance to the next parameter. To change the meter size, press UP or RIGHT to scroll to the correct meter size. Press ENTER to
advance to the next parameter.
OTE:N The meter size selection refers to the bore of the meter and not the connections size. For a listing of the Blancett
turbine bore sizes, see the default K-factor table in the Default K-Factor Values on page 20.
OTE:N In Programming mode, the monitor advances to the KFacUnit parameter.
See Select Meter’s K-Factor Unit* on page 12.

Programming
DSY-PM-00022-EN-07 Page 11August 2015
Select Display Function
The B3000 monitor has three display settings, Flow, Grand Total, and Test.
Flow
Use the Flow setting for normal operation of the monitor. In this mode, the display shows both the instantaneous flow rate
and current total simultaneously. See Figure 16.
2
1
Current Total Units
Flow Rate
Units
Totalizer
Multiplier
Current
Total
Instantaneous
Flow Rate
Figure 16: Instantaneous flow rate and current total
Grand Total
The Flow-GT setting forces the meter to alternate between the instantaneous flow and the grand total with roll-over counts.
See Figure 17.
The grand total is the accumulation of all the fluid that has gone through the meter since the last time the grand total was
cleared. This totalizer is in addition to the current total totalizer on the display and is always enabled.
In addition, the grand total screen displays the number of times the grand total has reached its maximum count (9,999,999)
and rolled over to zero.
2
1
Roll-Over
Indicator
Totalizer
Mode
Total
Roll-Overs
Figure 17: Grand total
Test
The Test setting places the monitor into a special diagnostic mode that shows the current input frequency and the
accumulated input counts. Figure 18 shows the layout for test mode values. The Test mode makes it possible for you to see
precisely the frequency input the monitor is seeing and is very useful in troubleshooting and noise detection.
2
1
Input
Frequency
Totalizer
Counts
Figure 18: Test mode screen
At the Display prompt, press ENTER to view the current display setting. If the current display setting is correct, press ENTER to
advance to the next parameter. To change the display setting, press UP or RIGHT to scroll through the display options. Press
ENTER to save and advance to the KFacUnit parameter.

Programming
DSY-PM-00022-EN-07Page 12 August 2015
Select Meter’s K-Factor Unit*
At the KFacUnt prompt, press ENTER. The display shows the current K-factor unit. If the current selection is correct, press
ENTER to advance to the next parameter. To change the K-factor unit, press UP or RIGHT to scroll to the correct unit, the units
should match the units that the meter was calibrated in. Press ENTER to save and advance to the KFactor parameter.
Enters Meter’s K-Factor*
OTE:N The K-factor supplied with your meter, or calculated from calibration data, is needed to complete this step.
At the KFactor prompt, press ENTER. The most significant digit in the K-factor flashes. If the current K-factor is correct, press
ENTER to advance to the next parameter. To change the K-factor, press UP to increment the digit until it matches the meter’s
first K-factor digit. Press RIGHT to advance to the next digit. Repeat this process until all K-factor digits have been entered.
Press ENTER to save the K-factor and advance to the RateInt parameter.
OTE:N The number of digits available before and after the decimal point is determined by the bore size of the flow sensor
being used. The largest K-factors are associated with the smallest bore sizes. The maximum allowable K-factor is
99999.9. The minimum must be at least 1.000. If an out of range number is entered, the display flashes Limit and
refuses the entry.
Select Rate Interval*
At the RateInt prompt, press ENTER. The monitor flashes the current time interval. If the current selection is correct, press
ENTER to advance to the next parameter. To change to an alternate time interval, press UP or RIGHT to scroll to the correct
time interval. Press ENTER to save and advance to the RateUnt parameter.
Select Flow Rate Units*
At the RateUnt prompt, press ENTER. The monitor flashes the current rate unit. If the current selection is correct, press ENTER
to advance to the next parameter. To change to an alternate unit, press UP or RIGHT to scroll to the correct rate unit and press
ENTER to save and advance to the TotlUnt parameter.
Select Total Units of Measure*
At the TotlUnt prompt, press ENTER. The monitor flashes the current total units. If the current selection is correct, press ENTER
to advance to the next parameter. To change to an alternate unit, press UP or RIGHT to scroll to the correct totalization unit.
Press ENTER to save and advance to the TotlMul parameter.
Select Total Multiplier*
This parameter displays the accumulated flow total in multiples of 10. For example, if the optimum totalization unit is 1000
gallons, the unit total display increments by one digit for every 1000 gallons monitored. In Run mode, at 1000 gallons the total
monitor reads 1, at 3000 gallons, the total display reads 3. This feature eliminates having to look at a total, count the digits,
and mentally insert commas for each 1000 multiple.
At the TotlMul prompt, press ENTER . The monitor shows the current total multiplier. If the selection is correct, press ENTER to
advance to the next parameter. To change to an alternate multiplier, press UP or RIGHT to scroll to the correct multiplier unit
and press ENTER to and advance to the next parameter.
OTE:N If the RateUnt or TotlUnt parameter has been set to pounds or kilograms, the monitor advances to the Spec Gr
parameter. At any other setting, the monitor advances to PulsOut in Programming mode. See Totalizer Pulse Output*
on page 14.
Enter Specific Gravity Value*
Mass readings in the B3000 monitor are not temperature or pressure compensated so it is best to enter the specific gravity
of the fluid as close to the system running temperature as possible. As liquids are essentially incompressible, pressure
compensation is not necessary for liquids.
At the Spec Gr prompt, press ENTER. The most significant digit of the current specific gravity flashes. If the current specific
gravity is correct, press ENTER to advance to the next parameter. To change to an alternate specific gravity, press UP to
increment the flashing digit until you reach the first digit of the new specific gravity. Press RIGHT to move to the next digit.
When all digits have been entered, press ENTER to save and advance to the next parameter.
OTE:N If Gas was chosen as the fluid, see Gas on page 19 and follow the directions for the gas parameters.
In Programming mode, the monitor advances to the PulsOut parameter, see Totalizer Pulse Output* on page 14.

Programming
DSY-PM-00022-EN-07 Page 13August 2015
Enter a Scale Factor
The scale factor is used to force a global span change. For example, in Run mode the display is reading a consistent three
percent below the expected values at all flow rates. Rather than changing the K-factor and linearization parameters
individually, the scale factor can be set to 1.03 to correct the readings. The range of scale factors is from 0.10…5.00. The
default scale factor is 1.00.
At the Scale F prompt, press ENTER. The first digit of the existing scale factor flashes. If the current selection is correct, press
ENTER to advance to the next parameter. To change to an alternate scale factor, press UP to increment the display digit until
it matches the first digit of the new scale factor. Press RIGHT to advance to the next digit. Repeat for all digits. Press ENTER to
save and advance to the SetTotl parameter.
OTE:N If the number you enter is out of range the display flashes Limit and refuses the entry.
Preset Total
The preset total parameter sets the totalizer to a predetermined amount. The preset can have seven digits up to 8,888,888.
At the SetTotl prompt, press ENTER. The monitor displays the current set total. If the set total is correct, press RIGHT to
advance to the next parameter. To change the set total, press ENTER again. The first digit of the current preset total flashes.
Press UP to increment the display digit until it matches the first digit of the correct preset. Press RIGHT to advance to the next
digit. Repeat for all digits. Press ENTER to save and advance to the Cutoff parameter.
OTE:N If the number you enter is out of range the display flashes Limit and refuses the entry.
Low Flow Cutoff
The flow cutoff shows low flow rates (that can be present when pumps are off and valves are closed) as zero flow on the flow
monitor. A typical value would be about five percent of the flow sensor’s maximum flow.
Enter the low flow cutoff as an actual flow value. For example, if the maximum flow rate for the flow sensor was 100 gpm, set
the low flow cutoff value to 5.0.
At the Cutoff prompt, press ENTER. The first digit of the current low flow cutoff flashes. If the current selection is correct,
press ENTER to advance to the next parameter. To change the low flow cutoff, press UP to increment the display digit until it
matches the first digit of the new low flow cutoff value. Press RIGHT to advance to the next digit. Repeat for all digits. Press
ENTER to save and advance to the Damping parameter.
OTE:N If the number you enter is out of range the display flashes Limit and refuses the entry.
OTE:N If the fluid being measured is set to Gas, the monitor advances to Op Pres in Extended Programming mode. See Gas on
page 19.
Damping Factor
The damping factor is increased to enhance the stability of the flow readings. Damping values are decreased to allow
the monitor to react faster to changing values of flow. This parameter can be any value between 0…99 %, with 0 being
the default.
At the Damping prompt, press ENTER. The most significant digit of the current setting flashes. If the current selection is
correct, press ENTER to advance to the next parameter. To change the damping value, press UP to increment the display digit
until it matches the new damping value. Press RIGHT to advance to the next digit. Press ENTER to save and advance to the
PulsOut parameter.

Programming
DSY-PM-00022-EN-07Page 14 August 2015
Totalizer Pulse Output*
The PulsOut parameter can be enabled or disabled. When enabled, the output generates a fixed width 30 mS duration, pulse
every time the least significant digit of the totalizer increments. The amplitude of the pulse is dependent on the voltage level
of the supply connected to the pulse output and is limited to a maximum 28V DC.
The B3000 monitor provides two types of totalizer pulses. The basic open drain FET output, Figure 19 and Figure 20, provides a
ground referenced output pulse that swings between about 0.7V DC and VCC.
JP1
JP2
JP3
P1
Freq. In
4-20mA
Iso Total Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
Total Reset
Total Pluse
Signal Gnd
Mag
Pulse
Iso
OC
Low
High
Input Total Pulse Signal
TB1
Open Drain FET
Total Pulse Output
2.2 …10k
Pullup
Resistor
VCC
Internal
100 mA
Maximum
Freq. In
4-20mA
Iso Total Pluse
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
JP3
Total Pulse
ISO OC
JP1
Input
MagPulse
TB2
Open Drain FET
Total Pulse Output
2.2…10k
Pullup
Resistor
VCC
Internal
100 mA
Maximum
Figure 19: Open drain connections (NEMA 4X) Figure 20: Open drain connections (Ex-Proof)
The isolated pulse output (ISO), Figure 21 and Figure 22, is an open collector output with the emitter of the transistor
connected to the negative output terminal and is not referenced to ground. This output is optically isolated from the input
signal for systems that require a totally isolated output pulse.
JP1
JP2
JP3
Input Total Pulse Signal
P1
JP1
JP2
JP3
Input Total Pulse Signal
P1
Freq. In
4-20mA
Iso Total Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
Isolated Output
Total Pulse
Internal
–V
2.2…10k
Pullup
Resistor
VCC
100 mA
Maximum
Freq. In
4-20mA
Iso Total Pluse
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
JP3
Total Pulse
ISO OC
JP1
Input
MagPulse
TB2
Internal
Isolated Output
Total Pulse
–V
2.2…10k
Pullup
Resistor
VCC
100 mA
Maximum
Figure 21: Opto-isolated open collector connections (NEMA 4X) Figure 22: Opto-isolated open collector connections (Ex-Proof)
Both outputs have a maximum current capacity of 100 mA and require a pullup resistor. The value of the pullup resistor is
dependent on the supply voltage and the maximum current required by the load device.
Flow at 20 mA
This setting normally represents the maximum rate of the flow sensor connected to the display, but other entries are possible.
At the Fl=20mA prompt, press ENTER. The first digit of the current setting flashes. If the current setting is correct, press ENTER
to advance to the next parameter. If the current setting requires a change, press UP to increment the display digit until it
matches the first digit of the required maximum flow value. Press RIGHT to advance to the next digit. Repeat for all of the
maximum flow at 20 mA digits. Press ENTER to save and advance to the 4-20Cal parameter.
In Programming mode, the monitor advances to the Clr G-T parameter. See Clear Grand Total on page 19.

Programming
DSY-PM-00022-EN-07 Page 15August 2015
4…20 mA Calibration
This setting allows the fine adjustment of the Digital to Analog Converter (DAC) that controls 4…20 mA output. The
4…20 mA output is calibrated at the factory and under most circumstances does not need to be adjusted. If the output needs
to be adjusted for any reason the 4…20 mA calibration procedure is used.
At the 4-20Cal prompt, press ENTER. The monitor displays No. If you do not need to complete the 4…20 calibration, press
ENTER to advance to the Linear parameter. See Linearization. To complete the 4…20 calibration, press UP or RIGHT to change
the display to Yes. Press ENTER to advance to the 4mA Out parameter.
The DAC used in the B3000 monitor is an twelve bit device. The valid entries are 0…4095.
P1
Freq. In
4-20mA
Iso Total Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
Total Reset
OC Total Pluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
+
+
–
–
Input Total Pulse Signal
JP1
JP2
JP3
4…20 mA
Current Loop
(11…30V DC)
POWER
SUPPLY
10A MAX
FUSED 400mA
FUSED
CATIII
1000V
HOLD MIN MAX REL
Hz % ms RANGE
AutoHOLD FASTMIN MX LOGGING YES
CANCEL SAVE NO
SETUP
µA
mA
A
W
V
TEMPERATURE
COM
OFF
nS
W
VIEW MEM
CLEAR MEM
V
dB
mV
dB
ac+dc
V
ac+dc
A
mA
mV
ac+dc
mA
A
µA
ac+dc
µA
°C
°F
MEM
HM
MS
51000
AUTO
MANUAL
%
FAST MAX MIN AVG
0 0
LOG
HOLD
Figure 23: 4…20 mA calibration setup
4 mA Adjustment
To set the 4 mA value, connect an ammeter in series with the loop power supply as shown in Figure 23. The 4 mA DAC setting
is typically 35…50. At the 4mA Out prompt, press UP to increase or RIGHT to decrease the current output while monitoring
the ammeter. When a steady 4 mA reading is established on the ammeter, press ENTER on the monitor to save the output and
advance to the 20mAOut parameter.
20 mA Adjustment
The 20 mA adjustment is performed using the same procedure as the 4 mA adjustment.
4…20 mA Test
The 4…20 mA test simulates the mA output values between 4…20 to check output tracking. At the 4-20 Test prompt
the current output flashes. Press UP to increase the simulated mA output or RIGHT to decrease in increments of 1 mA.
The ammeter should track the simulated mA output. If a 4…20 mA test is not necessary, press ENTER to advance to the
Linear parameter.
OTE:N Press ENTER when the monitor is in test mode to exit the test mode and move on to the next
programming parameter.
Linearization
To increase accuracy, linearize the monitor. The linearization function accepts a maximum of ten points and requires
additional calibration data from the meter being used with the monitor. Typically, calibration information can be obtained
in three, five and ten points from the flow meter’s manufacturer. If linearization is not needed, press RIGHT to advance to
the Modbus parameter. See Modbus on page 16. To complete linearization, press ENTER at the Linear prompt. The meter
advances to the Lin Pts parameter.

Programming
DSY-PM-00022-EN-07Page 16 August 2015
Number of Points
The Lin Pts value displays. If the number of points is set to 0, linearization is disabled. Press ENTER. The most significant digit
of the number of points entry begins to flash. The first number can be a 1or a 0only. Press UP to change the first digit. Press
RIGHT to move to the least significant digit.
OTE:N If the number you enter is out of range the display flashes Limit and refuses the entry.
Press ENTER to advance to the Freq#1 prompt.
OTE:N If the number of linear points is set to 1the B3000 monitor assumes you are entering the maximum frequency and
coefficient. Further, the meter assumes that the implied first point is at a frequency of 0 Hz and a coefficient of 0.
Frequency
At the Freq#1 prompt, press ENTER. The first digit of the first linear point’s frequency input flashes. Press UP to increment
the numerical values and RIGHT to change the position of the number being entered. When the frequency value input is
complete, press ENTER to save and advance to the Coef#1 parameter.
Coefficient
The coefficient is the value applied to the nominal K-factor to correct it to the exact K-factor for that point. The coefficient is
calculated by dividing the average (nominal) K-factor for that point by the actual K-factor for the flow meter.
Linear Coecient = Actual K-Factor
Nominal K-Factor
At the Coef#1 prompt, press ENTER. The first digit of the coefficient flashes. Press UP to increment the digit, and RIGHT to
move to the next digit. When all digits have been entered, press ENTER to save and advance to the next frequency input.
Continue entering pairs of frequency and coefficient points until all data has been entered. Press ENTER to save and advance
to the Modbus parameter.
OTE:N The frequency values must be entered in ascending order. If a lower frequency value is entered after a higher value,
the B3000 monitor flashes Limit followed by the minimum frequency value acceptable to the display.
Example:
The following is actual data taken from a one inch turbine flow sensor calibrated with water.
Unit Under Test (UUT) Calibration Data Table In GPM
Actual
gpm
UUT
Frequency
UUT Actual
K-factor
(Hz x 60)
Nominal K Linear
Coefficient
Raw Error
Hz Counts/US Gallon GPM % Rate
50.02 755.900 906.72 49.72 1.0060 0.59
28.12 426.000 908.96 28.02 1.0035 0.35
15.80 240.500 913.29 15.82 0.9987 –0.13
8.88 135.800 917.57 8.93 0.9941 –0.59
4.95 75.100 910.30 4.94 1.0020 0.20
Nominal K (NK) 912.144 — —
Table 2: Sample linearization data
In this example, the linear coefficient has already been calculated by the calibration program so all that is required is to enter 5
into the number of linear points Lin Pts parameter and then enter, in order, the five frequency, linear coefficient data pairs.
Modbus
The Modbus output parameter can be enabled or disabled. When enabled, communications with the B3000 monitor are
completed using the Modbus RTU protocol. For additional information see Modbus Interface on page 35.
At the Modbus prompt, press ENTER. The current state of the Modbus output is shown. If the current state is correct, press
ENTER to advance to the next parameter. To change the modbus setting, press UP or RIGHT to toggle between states. When
the proper state displays press ENTER to save and advance to the BusAddr parameter.

Programming
DSY-PM-00022-EN-07 Page 17August 2015
Bus Address
If the Modbus output is enabled, you must choose a valid Modbus address. Every device communicating over the RS485
communications bus using the Modbus protocol must have a unique bus address. Address values range from 0…127 with 0
being the default.
At the BusAddr prompt, press ENTER. The first digit of the address flashes. If the current setting is correct, press ENTER to
advance to the next parameter. To change the address, press UP to increment the display digit until it matches the first digit
of the new bus address. Press RIGHT to advance to the next digit. Repeat for all digits of the address. Press ENTER to save the
new address and advance to the SetPt 1 parameter.
Set Points
Set points allow the meter to signal when a specific flow condition has been achieved. They are commonly used to indicate
high or low flow conditions that need attention. The B3000 monitor has two open collector outputs controlled by the set
point function.
The set point transistors have the same current limitations and setup requirements as the totalizing pulse output transistors
described previously (see Figure 23 on page 15 , Figure 24 and Figure 25).
Both set point one and set point two are configured using the same procedures but the hysteresis and tripping conditions are
independently set for each set point output.
OTE:N In most instances, the current capacity of an open collector transistor is not sufficient to operate old style counters
that relied on relay contact closures. When used with basic counting circuits, a solid-state relay is needed.
Set Point 1
The set point is the flow value at which the output transistor changes state. It is set using the same units as the rate units.
JP1
JP2
JP3
Input Total Pulse Signal
P1
Freq. In
4-20mA
Iso Total Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
Open Collector
Control Output
1 and 2
2.2…10K
Pull-up
Resistor
VCC
Internal
100 mA
Maximum
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
P2 3.6Vdc
Battery
TB1
P1
P1
Internal
Open Collector
Control Output
1 and 2
2.2…10K
Pull-up
Resistor
VCC
100 mA
Maximum
Figure 24: Set point output (NEMA 4X) Figure 25: Set point output (Ex-Proof))
At the SetPt 1 prompt, press ENTER. The most significant digit of the current setting flashes. If the current setting is correct,
press ENTER to advance to the next parameter. To change the current setting, press RIGHT to advance to the first digit of the
required set point value. Press UP to increment the digit until it matches the first number of the required set point. Repeat for
all the digits the set point. Press ENTER to save the new set point and advance to the HystSP1 parameter.

Programming
DSY-PM-00022-EN-07Page 18 August 2015
Hysteresis 1
The hysteresis parameter modifies how the output transistor reacts around a set point and prevents an output from turning
on and off rapidly when the programmed flow rate is at, or very near, the set point.
For example, a low flow alarm is set to activate when the flow falls below a pre-programmed point. When the flow is reduced
to the set point, even small changes of flow above the set point turns the output off, disabling the alarm. Without hysteresis, if
the flow rate fluctuates slightly above and below the set point, the output rapidly cycles between on and off states. See
Figure 26. The hysteresis value is set using the same units as the rate units.
At the HystSP1 prompt, press ENTER. The most significant digit of the current setting flashes. If the current setting is correct,
press ENTER to advance to the next parameter. To change the current setting, press RIGHT to advance to the first digit of the
new hysteresis value. Press UP to increment the digit until it matches the first number of the new hysteresis. Repeat for all the
digits of the hysteresis and then press ENTER to save and advance to the TripSP1 parameter.
Minimum
Flow
Maximum
Flow
Output ON
OFF Setpoint ON Setpoint
Hysteresis
Output OFF
Figure 26: Set point actions
OTE:N Neither the set point nor the hysteresis values are checked for compatibility with the meter size. Check the values to
prevent the outputs from working unexpectedly.
Trip SP 1
The trip parameter can be set for either High or Lo. When set to high, the open collector transistor stops conducting and sends
the output high when the set point is reached. The output will not go low again until the flow rate falls below the set point
minus the hysteresis value. When set to low, the open collector transistor starts conducting and sends the output low when
the set point is reached. The output will not go high again until the flow rate exceeds the set point plus the hysteresis value.
For example, if the set point is 10 gpm, the hysteresis is set to 2 gpm and the trip set point is set to High (see Figure 27). When
the flow goes above 10 gpm, the OC transistor stops conducting and the output goes high. The output stays high until the
flow rate drops below 8 gpm, which is the set point (10 gpm) minus the hysteresis (2 gpm).
Minimum
Flow
Maximum
Flow
Output ON
OFF (8 gpm) Setpoint (10 gpm)
Hysteresis
(2 gpm)
Output OFF
Figure 27: Set point example
At the TripSP1 prompt, press ENTER. The current tripping condition setting displays. If the current setting is correct, press
ENTER to advance to the next parameter.
If the current setting requires a change, press UP or RIGHT to change to the alternate choice. Press ENTER to save and
advance to the SetPt 2 parameter.
The SetPt 2, HystSP2 and TripSP2 parameters are set using the same procedures as the SetPt 1, HystSP1 and TripSP1 parameters.
When these parameters have been entered, the monitor advances to the Clr G-T parameter.

Programming
DSY-PM-00022-EN-07 Page 19August 2015
Clear Grand Total
At the Clr G-T prompt, press ENTER. The monitor displays No on the screen. To clear the grand total, press UP or RIGHT to
change from No to Yes. Press ENTER to save and advance to the Passwd parameter.
The totalizer can also be reset using a hardware reset, as shown in the following diagrams and by pressing MENU and
ENTER simultaneously.
JP1
JP2
JP3
Input Total Pulse Signal
P1
Freq. In
4-20mA
Iso Total Pluse
TR_B
TR_A
RS485 Gnd
Setpoint 1
Setpoint 2
Gnd
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
TB1
Mag
Pulse
Iso
OC
Low
High
Input Total Pulse Signal
Normally Open
Pushbutton
Switch
Freq. In
4-20mA
Iso Total Pluse
+
–
+
–
+
–
Total Reset
OC Total Pluse
Signal Gnd
JP3
Total Pulse
ISO OC
JP1
Input
MagPulse
TB2
Normally Open
Pushbutton
Switch
Figure 28: NEMA 4X hardware reset Figure 29: Ex-proof hardware reset
Password
The password setting restricts access to the Programming and Extended Programming modes. Initially, the password is set to all
zeros and any user can modify the parameter settings. To change the password, press ENTER at the Passwd prompt. The first
digit flashes. Press UP to increment the digit and RIGHT to advance to the next digit. After entering all digits, press ENTER to
store the password and advance to RST PSWD. The new password is now required to enter either programming mode. With
this password set, any user is able to reset the stored totals on the monitor.
Reset Password
The reset password parameter restricts resetting the totals on the monitor. The Password must also be set to restrict the total
reset. Initially, the password is set to all zeros and any user can reset the stored totals on the monitor. To change the password,
press ENTER at the RstPswd prompt. The first digit flashes. Press UP to increment the digit and RIGHT to advance to the next
digit. After entering all digits, press ENTER to store the password and return to the Fluid parameter. The reset password is now
required to reset the totals on the monitor.
OTE:N Entering a password in the Passwd screen and leaving the password blank in the RstPswd screen allows for total resets
(not requiring a password), but restricts programming modification.
Gas
Operating Pressure
At the Op Pres prompt, press ENTER. The first digit of the current pressure setting flashes. If the current selection is correct,
press ENTER to advance to the next parameter. To change the operating pressure, press UP to increment the digit until it
matches the first digit of the correct pressure value. Press RIGHT to move to the next digit. When all the digits have been
entered, press ENTER to save and advance to the Op Temp parameter.
Operating Temperature
At the Op Temp prompt, press ENTER. The first digit of the current temperature setting flashes. If the current selection is
correct, press ENTER to advance to the next parameter. To change the operating temperature, press UP to increment the digit
until it matches the first digit of the correct pressure value. Press RIGHT to move to the next digit. When all the digits have
been entered, press ENTER to save and advance to the next parameter.
In Programming mode the monitor advances to the PulsOut parameter, see Totalizer Pulse Output* on page 14.
In Extended Programming mode, the monitor advances to the Damping parameter, see Damping Factor on page 13.
Return to Run Mode
After entering all parameters, press MENU. Saving displays on the menu, followed by a blank screen and then the firmware
version number. The monitor then returns to Run mode.

Troubleshooting Guide
DSY-PM-00022-EN-07Page 20 August 2015
TROUBLESHOOTING GUIDE
Trouble Remedy
No LCD
Display
Battery – B30A/B/X/Z only Check battery voltage. Should be 3.6V DC. Replace if low or bad.
Loop Power
OTE:N Not available on B30S
Check 4…20 mA input. Voltage must be within the minimum and maximum supply
voltage and capable of supplying enough current to run the display. The input voltage is
checked “across”or in parallel with the 4…20 mA terminals and current is checked with
the ammeter in series with the 4…20 mA output.
Solar Place meter with solar cell exposed to a strong light source for 24 hours.
No Rate or Total Displayed
Check connection from meter pickup to display input terminals.
Check turbine meter rotor for debris. Rotor should spin freely.
Check programming of flow monitor.
Flow Rate Display Interprets Reading
Constantly
This is usually an indication of external noise. Keep all AC wires separate from DC wires.
Check for large motors close to the meter pick-up.
Check for radio antenna in close proximity.
Try disconnecting the pickup from the monitor pig tail. This should stop the noise.
Flow Rate Indicator Bounces This usually indicates a weak signal. Replace pickup and/or check all connections.
Examine K-factor.
DEFAULT KFACTOR VALUES
Liquids
Meter Bore Size Default K-factor Lower Limit Upper Limit
0.375 20,000 16,000 24,000
0.500 13,000 10,400 15,600
0.750 2750 2200 3300
0.875 2686 2148 3223
1.000 870.0 696.0 1044
1.500 330.0 264.0 396.0
2.000 52.0 41.6 62.0
3.000 57.0 45.6 68.0
4.000 29.0 23.2 35.0
6.000 7.0 5.6 8.0
8.000 3.0 2.4 4.0
10.000 1.6 1.3 2.0
Gas
Meter Range Default K-factor
Low 325
Medium 125
High 80