Blaupunkt RC TY 1.0 User manual

Enjoy it.
Operating and Installation Instructions
REVERSE CAMERA
RC TY 1.0

•
•
•
This manual may be updated from time to
time without any notice.
Disclaimer
In no event shall Blaupunkt be liable for any
direct, indirect, punitive, incidental, special
consequential damages to property or life
and whatsoever arising out of or connected
with the use or misuse of our products.
USA & CANADA: This product is not intended
for sale in the United States and Canada. If
purchased in the U.S. or Canada, this product
is purchased on as-is basis. No warranty,
whether expressed or implied is provided in
the U.S. or Canada.
Safety Notes
This vehicle security system has been man-
ufactured according to established safety
guidelines. However, dangers may still occur
if the safety notes in this manual is not ob-
served. This manual is intended to familiarize
the user with the reverse camera important
functions. Read this carefully, prior to using
the reverse camera. Keep this manual in an
easily accessible location. In addition, do
observe the instructions of the devices used
in conjunction with this reverse camera.
Attentions
•
•
•
•
•
•
•
Assign a mounting location that will not
obstruct driver in any circumstances. Or
cause injuries to drives and passengers in
case of emergency brake or accidents.
Ensure all wires are connected properly,
and that the unit is functioning well before
tting the unit into the mount.
Any unauthorized installation, disassembly
or modication may cause malfunction to
the unit and void warranty of the unit.
Always use only the parts that are includ-
ed with the units only.
Do not damage vehicle components when
drilling holes for the mount.
Vehicle may dier from the description
provided here. Consult an authorized
Blaupunkt dealer or vehicle’s manufacturer
if the information provided here does not
t your specic installation requirement.
This unit is applicable for front and reverse
camera use. Consult an authorized
Blaupunkt dealer during installation.
Unit does not record video.
Avoid automatic car wash or high-pressure
water to prevent water and pressure
from damaging the camera or causing
it to fall o.
Do not install this unit near heater outlet.
1
CAUTIONS
2
SPECIFICATION
Features
CMOS Image Sensor
NTSC/PAL TV System
Eective Pixels
750TVL Image Resolution
25/30 Frame Per Second
Exposure & Gain Control
1/60~1/100000sec
Electronic Shutter
Auto White Balance
Illumination Min.
Horizontal View
Vertical View
Diagonal View
DC12V Voltage
Current
DC9-16V Operating
Voltage Range
Operating Temperature
Storage Temperature
Protection Grade
RCA/4 PIN DIN
Lens
RC TY 1.0


733 (H) x 493 (V)





0.1 Lux/F
155°H
135°V
170°D

65mA

-20~+70 °C
-30~+75°C
IP68

5glass

3 4
INSTALLATION LOCATION INSTALLATION DIAGRAM
Remove protective lm from camera lens before use.
Take extra precautions when setting up the connection near petrol tank and wires.
Connect Red Wire with reverse light.
Attention
•
•
•
Red Wire
P
R
N
D
L
2
Display Monitor/
Car Radio
Black Wire (Ground)
Reverse
Camera
Reverse Light
Ground the wire through the exterior body of the vehicle and keep connection intact.
Reverse Trigger
White
Blue
Purple
Reverse Camera
a) Reverse Camera
b) Front Camera
Display Monitor/Car Radio
TYPE 2
Tailgate
12
Drill an access hole for
the camera cables
Mount the camera
onto the access
hole & secure it with
screws
Remarks :
1. Pictures are for illustration purpose only, see actual vehicle for accurate installation location.
2. Ensure diameter of hole size is correct before drilling.
3. Ensure drilling process does not harm the component of the vehicle.
4. Assign mounting location that will not obstruct camera view.
TYPE 1
Car
Plate
12
Drill an access hole for
the camera cables
Mount the camera
onto the access
hole & secure it with
screws

FRONT / REAR CAMERA INSTALLATION
TROUBLESHOOTING
Problem
Display monitor / car radio does not
show reverse view when reversing.
Reverse view does not show even
after restarting the display monitor/
car radio.
Reverse view does not show even
though power supplies of the reverse
light or the rear car plate light is
properly connected.
Solution
Restart the display monitor / car radio.
Examine if the power supplies of the reverse
light or the rear car plate light is properly
connected.
Examine if the power supply cables of the
reverse light or the rear car plate light is
damaged. Repair/replace if the cables are
damaged.
If any of the following problem occur, please resort toTroubleshooting for the possible
solutions. Consult Blaupunkt authorized dealer if problem persist.
5 6
FRONT / REAR CAMERA INSTALLATION
Type 1 Installation Wiring
Reverse Camera Wiring
Cut white and purple wires when
using as reverse camera on rear
back door.
Before Cutting Wires
After Cutting Wires
Reverse Camera Wiring
Do not cut the wires when
using as reverse camera near
license plate.
Type 2 Installation Wiring
Rear Camera Wiring (Remove Parking Line)
Front Camera Wiring (Flip Viewing Display & Remove Parking Line)
Reverse Camera
Do not cut the wires when using
as reverse camera.
Rear Camera
Cut blue wire when using as front
camera to remove parking line.
Front Camera
Cut white & blue wires when using
as front camera to ip viewing
display & remove parking line.
Reverse Camera
Do not cut the wire when using
as reverse camera.

Designed and engineered by Blaupunkt Competence Centre 1 331 20 010 32 01