Blusafe Mirage User manual

Mirage Fingerprint Padlock
Product Fitting Instructions
Please read carefully before installation
Important
Upon initial use of the padlock and after a reset the lock can be
opened with each touch of the sensor.
The fingerprint sensor and finger that touches the sensor should
always be kept clean, dry and free from grease.
The fingerprints will remain stored when the battery runs low.
It is recommended to use this product in an environment where
it will not be exposed to heavy rain or salt water, or direct
sunshine, which could damage the internal electronics.
It is recommended to fully charge the padlock at room tempera-
ture before first use, this can take up to 5 hours. To aximise the
performance of the padlock’s lithium battery we recommend
fully recharging every 3 months.
Insert the USB cable into the socket in the padlock and charge
using a USB mains device or compatible mains wall plug.
The circular LED ring will light up red to indicate the padlock is
charging. When the red LED turns off charging is complete.
Close the rubber charging cover
1.On first use
Charge the battery
Fingerprint Registration
Water resistant lid
Press the fingerprint sensor to check that the battery has
charged fully. The fngerprint sensor is located in the centre of
the padlock. The circular LED ring around the sensor will light
up.
If the LED BLUE lights up - Normal power. Lock is ready.
If the LED PURPLE lights up & BEEP sounds- Low
power.Lock can still operate. Charge required.
If the LED PURPLE lights up and stays on - Very low power.
Note that if the padlock does not operate normally at anytime-
please charge the battery.
Average Recognition Time
FAR
Battery Life
Locking Force
Size
Capacity of Fingerprint
Spatial Resolution
FRR
Battery Capacity
Charging Current
N.W.
50-60KG (110-132lbs)
88×55×25mm (3-1/2" × 2-3/16" × 1")
203g(7oz)
Note: Operating temperatures of less than 0°C（32°F）may lead to a more
dramatic reduction in battery performance. During periods of very cold weather
more frequent checking of the battery level is recommended.
Stated battery life is based on optimal operational conditions. As with all lithium
batteries, performance can be noticeably affected by cold temperatures. When using
outside, check the battery level regularly. lf the LED turns purple on use, fully recharge
the Padlock to avoid complete battery depletion.
Battery Life
Please scan above
QR to get newest
manuals on Blusafe
Products
Watch the set-up tutorial by
scanning the QR code above with
your camera or going to: https://blu-
safesolutions.co.uk/how-to-videos/

Note that the first 3 registered fingerprints are all ADMIN
fingerprints. ADMIN fingerprints can be used to unlock the
padlock and to authorise new user fingerprints.
Press the fingerprint sensor with a registered fingerprint.
If a triple beep sounds and the LED GREEN flickers, validation
is ok and the padlock will open.
If a single beep sounds and the LED RED flickers, validation
has failed. Press the fingerprint sensor again with a registered
fingerprint.
Press the fingerprint sensor. 1 triple beep will sound and the LED
GREEN flickers. The LED BLUE lights up.
Fingerprint is authorised & ADMIN registration is now ready.
Press the fingerprint sensor a further 4 times. 1 beep will sound
and the LED GREEN flickers each time the sensor is pressed. On
the final press a triple beep sounds. ADMIN registration is
complete.
Using the setting needle provided, gently press the setting
microswitch (located under the rubber charging cover) for 5
seconds until 3 beeps sound and the LED RED lights up 3 times.
Press the fingerprint sensor with a registered ADMIN fingerprint.
A triple beep sounds and the LED green flickers. All fingerprint
data has now been deleted and the padlock has been reset.
If the LED PURPLE flickers and 1 beep sounds the padlock
requires charging. Use the USB cable provided to do this.
Recharge the padlock if it does not operate normally at any
stage of operation. If the problem persists, reset the padlock.
When registering fingerprints it is recommended that you press
your finger on the sensor in different positions so that the
fingerprint data is fully collected.
When the padlock has been reset there is no data saved, any
fingerprint can be used to unlock.
Press the fingerprint sensor with a registered ADMIN fingerprint
for authorisation. The LED BLUE flickers. Registration is now
ready.
Press the sensor with a USER fingerprint. If the LED GREEN
flickers and 1 beep sounds registration is valid.
Now press the sensor a further 4 times with the same USER
fingerprint. 1 beep will sound and the LED GREEN flickers each
time the sensor is pressed. On the final press a triple beep
sounds. USER registration is complete.
Note that an ADMIN fingerprint will be required to authorise the
register of new fingerprints on the padlock.
Set up the first ADMIN fingerprint. Using the setting needle
provided, gently press the setting microswitch (located under
the rubber charging cover) for 3 seconds until 1 beep sounds
and the LED BLUE lights up.
Using the setting needle provided, gently press the setting
microswitch (located under the rubber charging cover) for 3
seconds until 1 beep sounds and the LED BLUE lights up.
Fingerprint Registration
2. How to set up ADMIN Fingerprints
3. How to set up USER Fingerprints
2a
2b
2c
3a
3b
3c
Unlocking the Padlock
Deleting all fingerprints (reset)
A
B
Low battery indication
Notes
4
USER
Note: If the LED RED flickers with no beep sound the sensor
has not detected the fingerprint. Try again.
Note: For the 2nd ADMIN fingerprint to be registered step 2b
must be done using the 1st ADMIN fingerprint. For the 3rd
ADMIN fingerprint to be registered step 2b can be done
using either the 1st or 2nd ADMIN fingerprint.
It is recommended to register ALL 3 ADMIN fingerprints on
first use.
WARNING: Please do NOT push the needle too hard as this
can cause damage to the setting microswitch. A click should
be felt as the needle makes contact with the microswitch,
when operated correctly.
WARNING : Please do NOT push the needle too hard as this
can cause damage to the setting microswitch. A click should
be felt as the needle makes contact with the microswitch,
when operated correctly.
WARNING : Please do NOT push the needle too hard as this
can cause damage to the setting microswitch. A click should
be felt as the needle makes contact with the microswitch,
when operated correctly.
Note: If the LED RED flickers with no beep sound the sensor
has not detected the fingerprint. Try again.
4
Please scan above
QR to get newest
manuals on Blusafe
Products
Watch the set-up tutorial by
scanning the QR code above with
your camera or going to: https://blu-
safesolutions.co.uk/how-to-videos/