Blusafe Cloud User manual

Blusafe Cloud
Installation v1.0
Please scan the QR to get newest
manuals on Blusafe Products

P01
Security at your ngertips —— Blusafe

P02

P03
Installation Manual Contents
P01
P02
P03
P06
P07
0. Tools Required
1. Package Contents
2. Bolt Installation Guide
3. Blusafe Cloud Smart Lock
4. Installation of Blusafe Cloud Smart Lock

P04

P01
Tools Required

P02
Package Contents

P03
3. Fold the template guide along the edge of the door and position it over the 2 ⅛ "
(54mm) diameter hole. Mark the 1"(25mm) diameter hole on the edge of the door
for the bolt. Drill out the 1"(25mm) diameter bolt hole. Chisel out the remainder of
the slot on the edge of the door to accept the bolt body. This is a rectangle 1"x 2
¼" (26mm x 58mm) as shown above. The depth should be ⅛ " (3mm) to accept the
bolt body. Please test t the bolt body to ensure a good t before installing.
1. The Cloud Smart handle is
suitable to use on door thickness
between 1 ½"(38mm) and 2"
(50mm)
2. Use the template guide to mark a hole on the
door at the required height (the suggested
height for the centerline of the hole is 38
³ ∕₁₆ " (970mm) from the base of the oor.
Drill out a 2 ⅛ "(54mm) diameter hole.
The below bolt installation guide is meant for new doors that do not already have
holes for the lock or bolt. If your door already has the required holes to install the
bolt and lock, you may skip the below steps and proceed to P06.

P04
Adjust the bolt length according to the backset of the hole for the locking mechanism.
The bolt hole for the drive bar needs to be centered in the 2 ⅛ "(54mm) hole for the
lock's drive bar to go through. Once centered, place the bolt plate to the door as
shown above and screw x it.

P05
1. With the bolt installed, extend the bolt and
gently close the door against the door jamb.
Mark the locations where the top and bottom
of the bolt meet the door jamb.
2. Mark a center line down the door jamb for
the strike plate. Ensure the centerline allows
enough space for the door to close against the
door stop.
3. Place the strike plate on the door jamb,
aligning the marks you made from where the
bolt meets it to the hole for the bolt. Ensure
the strike plate is centered on the centerline
mark. Scribe around the outer edge of the
strike plate with a pencil, and chisel within the
scribed area to a depth of ⅛ "(2mm).
4. Insert the strike plate into the recessed hole
and mark the hole for the bolt.
5. Chisel the hole out to a depth of 1"(25mm) to
allow the bolt to extend and move freely.
6. Insert the bolt box and strike plate into the
hole. Screw in the strike plate as shown.

P06
Internal
Panel
Battery
Cover
Deadlock
Button
Knob
Keypad
Backup Key Hole
Fingerprint
Sensor
External
Panel
Blusafe Cloud Smart Lock
Micro USB Portal
Reset Hole
Loudspeaker Hole

P07
Installation of Blusafe Cloud Smart Lock
Cut the drive bar to
appropriate length according
to the door thickness.
No. of sections to be cut Screw B Length
M4 x 20mm
M4 x 20mm
M4 x 25mm
Door Thickness
1-½" to 1-"(38-40mm)
1-"to 1-¾"(40-45mm)
1-¾"to 2"(45-50mm)
2
1
/
1. Measure the door thickness.
2. Cut the drive bar to the appropriate length according
to the door thickness. Please see above graphic for
reference.
3. Please select the appropriate screws based on the
door thickness. You can refer to the above table for
reference.
Please make sure the bolt is installed properly as per the "Bolt
Installation Guide" on P03 prior to the following installation
steps:

P08
Installation of Blusafe Cloud Smart Lock
Make sure the cable
is pulled through the
bottom of hole.
Make sure the drive bar
is in the vertical position
when inserting.
CScrew Pillars
Ensure to put the bolt into the door
as per diagram, its crucial for the
installation procedure.
1. Tighten the "C screw pillars"onto the back of the external
panel.
2. Pull the cable of the external panel through the bottom
of the hole. Ensure the bolt is retracted (as per diagram).
Insert the drive bar into the "+"slot of the body; ensure the
drive bar is in the vertical position (as per diagram). Push
the external panel carefully into the door.

P09
The cable MUST
be pulled through
this slot.
Installation of Blusafe Cloud Smart Lock
3. Pull the cable through the slot of the mounting plate.

P10
One self tap screw A can be
used to assist the xing of the
mounting plate.
Installation of Blusafe Cloud Smart Lock
4. Drive the screws in but do NOT tighten them all the way.
Adjust the external panel to the correct position and then
proceed to tighten the screws.

P11
Installation of Blusafe Cloud Smart Lock
5. Insert the pin into the hole at the top of the internal panel.
Push the pin down to open the battery cover.

P12
Red
Red
Ensure the two
arrows meet.
Installation of Blusafe Cloud Smart Lock
6. Insert the cable into allocated slot on the internal panel.
Ensure the red faces of the cable connector and slot are
met.

P13
Installation of Blusafe Cloud Smart Lock
7. Hook the internal panel onto the mounting plate to connect.

P14
Fix the D screws with a screw driver.8.
Note: Please fasten the screws to sit ush with the inner face of the battery cassette.
Protrusion of the screws may cause damage to the batteries.
Installation of Blusafe Cloud Smart Lock