Body Craft F620 User manual

BACK & ARM STRENGTH TRAINING SYSTEM
INSTRUCTION MANUAL
MODEL : F620
Bodycraft is a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have
questions, or find missing or damaged parts, we will guarantee your complete satisfaction through
our authorized dealer service centers or our home office customer service department. Please call
your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained
technicians will provide immediate assistance to you, free of charge.
7900

1
BEFORE YOU BEGIN
For your safety and benefit, read this manual and the accompanying literature
before using the BODYCRAFT BACK & ARM MACHINE. Keep this manual
for future reference. If you have additional questions, please call your local
BODYCRAFT dealer or our customer service department at 800-990-5556
Monday through Friday, 9 a.m. until 5 p.m. Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1.This product must be assembled on a flat, level surface to assure its
proper function.
2.Clean pads and frame on a regular basis. We recommend warm,
soapy water. Do not use harsh or abrasive chemicals.
3.Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4.Keep children away from the BODYCRAFT BACK & ARM MACHINE
at all times.
5.Keep your hands away from cables and pulleys during operation.
Keep your hands away from moving parts other than the designated
handles.
6.When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
7.Make certain all cables are seated within the pulleys before every use.
8.Exercise with care to avoid injury.
9.If unsure about the proper use of the BODYCRAFT BACK & ARM
MACHINE strength training system call your local BODYCRAFT dealer
or our customer service department at 800-990-5556.

2
PARTS LIST
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
BASE FRAME
REAR STABILIZER
FRONT STABILIZER
UPRIGHT POST
WEIGHT HOLDER
MAIN UPRIGHT
TOP FRAME
FOOT PLATE
STEEL BUSHING
ADJUSTABLE TUBE
SEAT BAR
ROLLER BAR
SUPPORT PLATE
SPRING COIL
DOUBLE PULLEY BRACKET
CURL BAR
LAT BAR
LINK PLATE
RINGLET
5 LINK CHAIN
13 LINK CHAIN
POP PIN
HOOKUP
SPRING CLIP
50 MM ID SQ. BUSHING
50 MM OD SQ. SPACER
50 X 75 MM RECT. END PLUG
50 MM SQ. END CAP
1" OD ROUND END PLUG
PULLEY
TOP CABLE
LOW CABLE
ARM CURL PAD
ARM CURL BASE BOARD
SEAT PAD
FOAM ROLLER
200 MM LONG HAND GRIP
140 MM LONG HAND GRIP
1/2" WASHER
3/8" WASHER
1/2" NYLON NUT
3/8" NYLON NUT
1/2" X 3-1/8" HEX HEAD BOLT
1/2" X 1" HEX HEAD BOLT
3/8" X 3" HEX HEAD BOLT
3/8" X 1-3/4" HEX HEAD BOLT
3/8" X 1" HEX HEAD BOLT
3/8" X 2-3/4" HEX HEAD BOLT
5/16" x 1/4" SOCKET HEAD SCREW
DESCRIPTION
1
1
1
1
1
1
1
1
8
1
1
1
2
1
1
1
1
1
2
1
1
2
4
2
2
2
1
4
2
7
1
1
1
1
1
2
2
2
16
24
6
13
6
4
6
3
4
4
2
QTY.

3
OVERVIEW
48
48
48
44
44
39
45
46
46
47
42
42
42
42
42
42
46
42
40
40
40
40
45
48
44 44
39
9
45
42
42
42
40
40
40
40
43
43
43
39
39
39
39
41
41
41
39
49
41
47 47
47
40 40
40
40
40
40
9
9
9
9
9
9
43
43
45
41
41
42
39 39
39
39
39
40
37
37
27
30
30
30
30
30
29
36
38
36
29
26
26
22
22
28
28
28
28
30
30
25
25
24
24
17
7
33
6
34
35
11
3
10
12 16
18
19
8
13 13
15
2
14
4
5
1

4
PARTS CHART
BASE
FRAME(1)
REAR
STABILIZER(2)
FRONT
STABILIZER(3)
FOOT PLATE(8) SEAT BAR(11)
WEIGHT
HOLDER(5)TOP FRAME(7)
SPRING
COIL(14)
DOUBLE PULLEY
BRACKET(15)
LINK PLATE(18) RINGLET(19)
ROLLER BAR(12)
LAT BAR(17)
UPRIGHT POST(4)
MAIN UPRIGHT(6)
LINK PLATE(13) CURL BAR(16) ADJUSTABLE
TUBE(10)

5
PARTS CHART
STEEL
BUSHING(9)
POP PIN(22) SPRING
CLIP(24)
HOOKUP(23)
50 MM ID
SQ. BUSHING(25)
50 MM OD SQ.
SPACER(26)
50 X 75 MM RECT.
END PLUG(27)
50 MM SQ.
END CAP(28)
PULLEY(30)
TOP CABLE(31) 5 LINK
CHAIN(20)
LOW CABLE(32) 13 LINK
CHAIN(21)
1" OD ROUND
END PLUG(29)
ARM CURL PAD(33) ARM CURL
BASE BOARD(34)
SEAT PAD(35)
200 MM LONG
HAND GRIP(37)
140 MM LONG
HAND GRIP(38)
FOAM
ROLLER(36)

6
FASTENER
1/2" x 3-1/8" HEX HEAD BOLT(43)
1/2" x 1" HEX HEAD BOLT(44)
3/8" x 3" HEX HEAD BOLT(45)
3/8" X 1-3/4" HEX HEAD BOLT(46)
3/8" X 2-3/4" HEX HEAD BOLT(48)
3/8" X 1" HEX HEAD BOLT(47)
1/2" NYLON NUT(41)
3/8" NYLON NUT(42)
1/2" WASHER(39)
3/8" WASHER(40)
5/16" X 1/4" SOCKET HEAD
SCREW(49)
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4"

7
STEP 1 ASSEMBLE BASE FRAME
CAP REAR STABILIZER(2) AND FRONT STABILIZER(3) WITH 50 MM SQ. END
CAPS(28).
PLACE BASE FRAME(1) ON FLOOR. THEN ATTACH REAR STABILIZER(2) AND
FRONT STABILIZER(3) TO BASE FRAME(1) EACH USING TWO 1/2" X 3-1/8"
HEX HEAD BOLT(43), FOUR 1/2" WASHER(39) AND TWO 1/2" NYLON NUT(41).
To ease the assembly process, do not tighten bolts until instructed.
1
3
2
28
28 28
28
43 39
43 39
39 41
43
39
39
43
39
41
39
41
39 41

8
STEP 2 ASSEMBLE UPRIGHT FRAME
ATTACH UPRIGHT POST(4) TO REAR STABILIZER(2) USING TWO 3/8" X 3" HEX
HEAD BOLT(45), FOUR 3/8" WASHER(40) AND TWO 3/8" NYLON NUT(42).
ATTACH MAIN UPRIGHT(6) TO BASE FRAME(1) USING TWO 1/2" X 1" HEX HEAD
BOLT(44) AND TWO 1/2" WASHER(39). THEN ATTACH SUPPORT PLATES(13) TO
BASE FRAME(1) AND MAIN UPRIGHT(6) USING TWO 1/2" X 3-1/8" HEX HEAD
BOLT(43), FOUR 1/2" WASHER(39) AND TWO 3/8" NYLON NUT(41).
SLIDE SPRING COIL(14) ONTO UPRIGHT POST(4).
1
2
14
4
6
13
13
43
39
43 39
45
45 40
40
40
40
42
42
39 41
41
44
44
39
39

9
STEP 3 ASSEMBLE TOP FRAME
ATTACH TWO SPRING CLIPS(24) TO BARS OF WEIGHT HOLDER(5).
SLIDE WEIGHT HOLDER(5), WITH FLANGE DOWN AND CABLE ATTACHMENT
FORWARD OVER UPRIGHT POST(4).
INSERT 50 X 75 MM RECT. END PLUG(27) INTO TOP FRAME(7).
ATTACH TOP FRAME(7) TO MAIN FRAME(6) USING TWO 1/2" WASHER(39)
AND TWO 1/2" X 1" HEX HEAD BOLT(44). ATTACH TOP FRAME(7) TO UPRIGHT
POST(4) USING TWO 3/8" X 3" HEX HEAD BOLT(45), FOUR 3/8" WASHER(40)
AND TWO 3/8" NYLON NUT(42).
4
5
24
24
6
4
7
44
44
39
39
45
45
40
40
40
40
42
42
27