Body Craft F410 User manual

SMITH STRENGTH TRAINING SYSTEM
INSTRUCTION MANUAL
MODEL : F410
Bodycraft is a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have
questions, or find missing or damaged parts, we will guarantee your complete satisfaction through
our authorized dealer service centers or our home office customer service department. Please call
your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained
technicians will provide immediate assistance to you, free of charge.

1
BEFORE YOU BEGIN
For your safety and benefit, read this manual and the accompanying literature
before using the BODYCRAFT SMITH MACHINE. Keep this manual for future
reference. If you have additional questions, please call your local BODYCRAFT
dealer or our customer service department at 800-990-5556 Monday through
Friday, 9 a.m. until 5 p.m. Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1.This product must be assembled on a flat, level surface to assure its
proper function.
2.Clean pads and frame on a regular basis. We recommend warm,
soapy water. Do not use harsh or abrasive chemicals.
3.Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4.Keep children away from the BODYCRAFT SMITH MACHINE at
all times.
5.Keep your hands away from cables and pulleys during operation.
Keep your hands away from moving parts other than the designated
handles.
6.When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
7.Make certain all cables are seated within the pulleys before every use.
8.Exercise with care to avoid injury.
9.If unsure about the proper use of the BODYCRAFT SMITH MACHINE
strength training system call your local BODYCRAFT dealer or our customer
service department at 800-990-5556.

2
PARTS LIST
NO. DESCRIPTION QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
1
1
2
2
1
2
1
2
2
2
1
2
2
2
4
2
4
4
4
8
2
8
2
2
4
36
8
14
4
2
1
1
2
1
RIGHT BASE FRAME
LEFT BASE FRAME
REAR STABILIZER
UPRIGHT POST
SUPPORT FRAME
CROSS FRAME
GUIDE ROD
WEIGHT LIFTING BAR
BAR HOLDER
BAR SAFETY
SAFETY HOOK
FOOT PLATE
TEMPLATE
CONNECT PLATE
OLIMPIC ADAPTOR SLEEVE
50 mm END SQ. CAP
50 mm END SQ. PLUG
1-1/8" ID. ROUND BUSHING
1" ID. ROUND BUSHING
1/2" X 3" HEX HEAD BOLT
1/2" X 2-3/4" HEX HEAD BOLT
1/2" X 2-1/2" HEX HEAD BOLT
1/2" X 1" HEX HEAD BOLT
3/8" X 3" HEX HEAD BOLT
3/8" X 2-3/4" HEX HEAD BOLT
5/16" X 8mm SOCKET HEAD SCREW
1/2" WASHER
3/8" WASHER
1/2" NYLON NUT
3/8" NYLON NUT
1/2" SOCKET HEAD CAP SCREW
FOAM PAD
FOAM PAD BINDER
SPRING COIL
HEX HEAD WRENCH

3
OVERVIEW
6
21
27
26
17
17
4
7
21
27
26
4
7
33
32
29
27
8
29
27
19
18
9
19
18
31
15
19
9
18
18
19
15
31
23
27
27
23
27
29
29
27
5
12 16
14
1
20
27
16
27
28
26
21
25
24
16
2
26
21 27
24
25
28
27 29
28 30
28
30
27
27
29
29
16
27
27
23
23
5
27
14
20
28
30
29
28
30
27
10
13 11
29
27
27
22
34
3
22
13
34
11
27
29
27
10

4
PARTS CHART
RIGHT BASE
FRAME(1)
LEFT BASE
FRAME(2)
REAR
STABILIZER(3)
UPRIGHT POST(4)
GUIDE ROD(7)
WEIGHT LIFTING BAR(8)
CROSS
FRAME(6)
FOOT
PLATE(12)
SUPPORT FRAME(5) TEMPLATE(13) CONNECT
PLATE(14)
OLIMPIC ADAPTOR
SLEEVE(15)
BAR HOLDER(9) BAR
SAFETY(10)
SAFETY
HOOK(11)

5
PARTS CHART
50 MM END
SQ. CAP(16)
50 MM END
SQ. PLUG(17)
1-1/8" ID. ROUND
BUSHING(18)
1" ID. ROUND
BUSHING(19)
HEX HEAD
WRENCH(35)
FOAM PAD(32) FOAM PAD
BINDER(33)
SPRING COIL(34)
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4"
FASTENER
1/2" X 3" HEX HEAD BOLT(20)
3/8" X 2-3/4" HEX HEAD BOLT(25)
3/8" X 3" HEX HEAD BOLT(24)
1/2" X 1" HEX
HEAD BOLT(23)
1/2" X 2-3/4" HEX HEAD BOLT(21)
1/2" X 2-1/2" HEX HEAD BOLT(22) 3/8" NYLON
NUT(30)
1/2" NYLON
NUT(29)
3/8" WASHER(28) 1/2" WASHER(27)
1/2" SOCKET HEAD
CAP SCREW(31)
5/16" X 8 MM HEX
HEAD SCREW(26)

6
STEP 1 ASSEMBLE BASE FRAME
CAP RIGHT BASE FRAME(1) AND LEFT BASE FRAME(2) WITH 50 MM SQ.
END CAP(16). 
PLACE REAR STABILIZER(3) ON FLOOR THEN ATTACH RIGHT
BASE FRAME(1) AND CONNECT PLATE(14) TO THE RIGHT SIDE OF REAR
STABILIZER(3) USING TWO 1/2" X 3" HEX HEAD BOLT(20), FOUR 1/2"
WASHER(27) AND TWO 1/2" NYLON NUT(29).
DUPLICATE PROCEDURE TO ATTACH LEFT BASE FRAME(2) TO REAR
STABILIZER(3).
ATTACH FOOT PLATE(12) TO BASE FRAME(RIGHT(1) & LEFT(2)) USING TWO
3/8" X 3" HEX HEAD BOLT(24), TWO 3/8" X 2-3/4" HEX HEAD BOLT(25), EIGHT
3/8" WASHER(30) AND FOUR 3/8" NYLON NUT(30).
To ease the assembly process, do not tighten bolts until instructed.
3
1
14
2
12
14
28
2830
28
28
30
30
28
30
28
27
2729
27
27
29
29
27
29
27
24
25
24
25
16
16
16
16
20
20

7
STEP 2 ASSEMBLE UPRIGHT FRAME
ATTACH UPRIGHT POST(4), SLOTS FACING FRONT, TO RIGHT BASE FRAME(1)
USING TWO 1/2" X 2-3/4" HEX HEAD BOLT(21), FOUR 1/2" WASHER(27) AND
TWO 1/2" NYLON NUT(29). THEN ATTACH SUPPORT FRAME(5) TO RIGHT BASE
FRAME(1) AND UPRIGHT POST(4) USING FOUR 1/2" X 1" HEX HEAD BOLT(23)
AND FOUR 1/2" WASHER(27).
REPEAT THE PROCEDURE AS ABOVE FOR LEFT BASE FRAME(2).
1
2
21
21
27
27
27
27
27
27
27 27
27
23
23
23
23 27
23
23
23
23
27
27
27
29
29
29
4
4
5
5

8
STEP 3 INSTALL LIFTING SYSTEM
LOOSEN 5/16" X 8 MM SOCKET HEAD SCREW(26) THAT IS PRESET ON RINGLET
(WELDED ON BASE FRAME(#1 & #2)), THEN INSERT GUIDE ROD(7) INTO THE
RINGLET OF BASE FRAME(#1 & #2).
ATTACH SAFETY HOOKS(11) TO BAR SAFETY(10) USING 1/2" X 2-1/2" HEX
HEAD BOLT(22), TWO 1/2" WASHER(27) AND 1/2" NYLON NUT(29).
SLIDE BAR SAFETYS(10) ONTO GUIDE RODS(7) AND LET SAFETY HOOKS(11)
REST IN THE BOTTOM SLOT OF UPRIGHT POST(4).
SLIDE SPRING COIL(34) AND TEMPLATE(13) ONTO EACH GUIDE ROD(7).
INSERT TWO 1-1/8" ID. ROUND BUSHING(18) INTO BAR HOLDER(9).
SLIDE BAR HOLDER(9) ONTO WEIGHT LIFTING BAR(8).
SLIDE BAR HOLDERS(9) ONTO GUIDE RODS(7) AND REST BAR HOOKS IN
UPRIGHT POSTS(4) SLOTS.
1
2
7
7
26
26
7
9
9
8
11
10
13
13
10
11
7
18
18
18
27
34
34
22
22
22
22
18

9
STEP 4 ASSEMBLE CROSS FRAME
PLUG CROSS FRAME(6) WITH 50 MM SQ. END PLUG(17).
UNSCREW 5/16" X 8 MM SOCKET HEAD SCREW(26) ON RINGLET WELDED ON
CROSS FRAME(6).
PLACE CROSS FRAME(6) TOP-DOWN AND LET THE RINGLET OF CROSS
FRAME(6) ONTO GUIDE ROD(7). THEN ATTACH CROSS FRAME(6) TO UPRIGHT
POST(4) USING FOUR 1/2" X 2-3/4" HEX HEAD BOLT(21), EIGHT 1/2" WASHER(27)
AND FOUR 1/2" NYLON NUT(29).
TIGHTEN ALL BOLTS.
4
6
7
7
4
17
17
26
26
27
27
27
27
21
21
29
29