Bodyworx JI1830M User manual

TABLE OF CONTENTS
OVERVIEW DRAWING 2 ASSEMBLY STEPS 6
SAFETY INSTRUCTIONS 3 CAUTION 9
GROUNDING INSTRUCTIONS 3 MAINTENANCE 10
PRE-ASSEMBLY CHECK LIST 5 COMPUTER OPERATION INSTRUCTION 11
OVERVIEW DRAWING
2

IMPORTANT SAFETY INSTRUCTIONS
W en using t is product, basic precautions s ould always be followed, including t e following:
Please read t e instructions carefully before starting to use t is product.
DANGER – To reduce t e risk of electric s ock:
1. Always unplug t is product from t e electrical outlet immediately after using and before cleaning t e
treadmill.
WARNING – To reduce t e risk of burns, fire, electric s ock, or p ysical injury:
1. T is product s ould never be left unattended w ile plugged in. Unplug t is product from t e outlet
w en not in use or before putting on or taking clot ing and ot er belongings.
2. To avoid any danger, close supervision is necessary w en t is product is used by c ildren or
disabled persons; especially w en t is mac ine is operating.
3. Be sure to use t is product only for its intended use as described in t is manual. Do not use any
attac ment no recommended by t e manufacturer in order to avoid any danger or accidents.
4. Never operate t is product if it as a damaged cord or plug, if it is not working properly, if it as been
damaged, or dropped into water. Please return t is product to t e service centre or seller for
examination and repair.
5. Do not carry t is product by t e supply cord or use t e cord as a andle.
6. Keep t e cord away from ot surfaces or ground.
7. Never operate t is product wit t e air vents blocked. Keep t e air vents free of any obstructions to
avoid azards.
8. Never drop or insert any objects into any vent of t e treadmill.
9. Do not use or operate outdoors.
10. Do not operate w ere aerosol (spray) products are being used or w ere oxygen is t in.
11. Before turning t is product power off, turn all controls to t e off position t en remove t e plug from
t e outlet.
12. Connect t is product to a properly grounded outlet only.
13. If t e power cord is damaged, be sure to ask t e manufacturer or seller for replacement to avoid
accidents.
GROUNDING INSTRUCTIONS
T is product must be grounded first. If malfunction or breakdown occurs, grounding will provide a pat of
least resistance for electric current to reduce t e risk of electric s ock. T is product is equipped wit a cord
aving an equipment-grounding conductor and a grounding plug.
3

T e plug must be plugged into an appropriate outlet t at is properly installed and grounded in accordance
wit all local codes and ordinances.
DANGER – Improper connection of t e equipment-grounding conductor can result in a risk of electric
s ock. C eck wit a qualified electrician or serviceman if you are in doubt as to w et er t is product is
properly grounded. Do not modify t e plug provided wit t is product – if it will not fit t e outlet; ave a proper
outlet installed by a qualified electrician.
T is product is for use on a normal 220V – 240V and as a grounding plug t at looks like t e plug illustrated
in t e figure below. Make sure t at t is product is connected to an outlet aving t e same configuration as
t e plug. T ere is no need to use any adaptor for t is product.
Figure
Grounding Met ods
4

PRE-ASSEMBLY CHECK LIST
ITEM Description Qty ITEM Description Qty
A Frame 1 A Truss Hex Screw: M8xP1.25x40 2
B Left Decoration Cover 1 B Truss Hex Screw: M8xP1.25x15 4
C Rig t Decoration Cover 1 C Truss P ilips Screw: M5xP0.8x20 6
D Left Handrail Cover 1 D Plastic Was er 8x22x6T 4
E Rig t Handrail Cover 1 E Hex Wrenc + Screwdriver
5mm (70mm x 70mm)
1
F Cup Holder 2 F Safety Key / Clip 1
G Truss P ilips Screw: M5xP0.8x8 2
H Was er 6 x 13 x 1.5T 2
I MP3 Sound Cable 1
J SILICON 1
K Bottle 1
5

ASSEMBLY STEPS
Warning:
Don't untie t e loinclot until
assembly is finis ed.
If you untie t e loinclot first,
it may cause a azard
Loin Clot
Two persons are required to finis t e
assembly steps.
(Caution!! Please follow exactly t e
assembly steps below to avoid injury.)
1. Put up t e andrail tubes of Frame
(A) as t e arrow s ows in t e rig t
drawing and tig ten wit Hex screws
(a).
P.S. To avoid unexpected accidents,
always assemble t e treadmill wit
more t an one worker, do not
assemble by yourself.
6

2. Put up Uprig t (L & R) as s own in
t e rig t drawing and tig ten wit
Hex screws (b)
P.S. To avoid unexpected accidents,
always assemble t e treadmill wit
more t an one worker, do not
assemble by yourself.
3. After tig tening t e left and rig t uprig ts,
insert t e left and rig t decoration covers
(B & C) onto t e frame and tig ten wit
P ilips screws (c) and Was ers (d).
7

4. Wedge t e left and rig t andrail
covers (D & E) onto t e corresponding
positions as s own in t e rig t drawing
and tig ten wit Truss P ilips screws
(g) and was ers ( ).
5. Wedge cup older (F) onto t e
corresponding positions as s own
in t e rig t drawing
8

CAUTION
Note: T e Cylinder contains ig pressure gas.
Please avoid cras ing wit ot er objects in order to
avoid azards.
Note: If t e Cylinder is it, it mig t be damaged and
cause t e usage to incorrectly operate normally. T e
treadmill mig t fall w ile folding.
T is treadmill as a foldable mec anism for
storage. Stop all movements (including stopping t e
running belt and take off t e power cord) before
storage, t en pull t e Pop Pin of rig t side and fold
t e main frame till t e Pop Pin is clicked into position
into t e ole correctly and free your and. On t e
contrary, if you want to use t e treadmill, pull t e Pop
Pin as t e direction s own in t e rig t drawing (You
must old t e frame to avoid falling), and pull down
t e main frame onto t e ground slowly.
(P.S.1. To prevent azards, be careful if c ildren are
around)
(P.S.2. If you want to move t e treadmill, fold t e
treadmill first, old t e rear adjust cap wit your
ands, t en lean t e treadmill and do not move t e
treadmill until t e roller can be moved smoot ly.)
(P.S.3. Do not move t e treadmill on uneven
ground.)
9

MAINTENANCE
1. If t e belt tends to move off t e centre, stop t e
treadmill. Take t e L-s aped Wrenc and adjust t e
Hex Screw in t e Rear End Cap. For example, if t e
running belt is moving towards t e left side, tig ten
t e left Hex Screw about 1/4 turn (clockwise); if t e
running belt is moving towards t e rig t side, tig ten
t e rig t Hex Screw about 1/4 turn (clockwise). Turn
on t e treadmill after it as been adjusted. If you find
t at t e belt as not moved to t e proper position,
please repeat t e steps above. Don't use t e
treadmill until t e running belts returns to t e centre
position.
(P.S.1. T is procedure is very important, if t e belt is
not in t e centre, be sure to follow t e above steps.)
(P.S.2. T e position of t e running belt mig t not stay
precisely in t e centre wit slig tly towards t e left
and rig t sides, and t e situation varies wit ow
end-users use t is product. T ere is no need to
adjust t e belt if it does not rub against t e parts
inside.)
(P.S.3. Depending on t e usage of t is product,
please apply SILICON on t e board according to t e
c art located on t e next page. Use t e HEX Wrenc
to unscrew t e bolt inside t e Rear Roller. T en pull
t e belt up and daub some SILICON to t e centre of
t e board. After t at, adjust t e belt to t e centre of
t e deck, followed by tig tening t e screw to t e
original set.
(P.S. W en t e belt is sliding, please follow t e
above met od to lubricate t e running belt.)
10

SILICON SERVICING CHART
KM / Mile SPEED SERVICE INTERVAL
KM 6 KM/HR Below 1 Year
6 ~ 12 KM / HR 6 Mont s
12 KM / HR Above 3 Mont s
Mile 4 Mile / HR Below 1 Year
4 ~ 8 Mile / HR 6 Mont s
8 Mile / HR Above 3 Mont s
Note:
T is maintenance is intended for ouse old use.
If used for business, it is suggested to examine t is product every ot er mont .
COMPUTER OPERATION INSTRUCTION
COMPUTER CONSOLE
11

LCD PANEL
GENERAL OPERATION:
1) User Weig t Setting Mode
•Press SPEED + / - : Weig t setting 23 Kg ~ 130 Kg.
•Press ENTER : into t e START / READY mode.
•Preset Weig t is 70 Kg.
2) Manual Mode
➢START / READY Mode
Press START : countdown 3 seconds into sport mode (all rate is plus value).
Press STOP / RESET : press one time t e panel will s ow PUS and all rate is stop blinking,
press STOP contain 3 seconds again and back to t e START / READY mode.
➢PANEL WINDOW INDICATION
TIME / AGE : indicate time (0:00).
DISTANCE / HEIGHT : indicate distance (0.0).
CALORIES / INCLINE / SEX : indicate calories (0).
SPEED : indicate (0.0).
Pulse / WEIGHT : indicate Heart Rate if no Heart Rate value indicate (P).
Indicate MENU
➢SPORT MODE
Press SPEED + / - : setting speed
Press INCLINE + / - :
Press STOP / RESET :
12

Press START : countdown
Press 3 / 6 / 9 : setting speed
Press 3 / 6 / 9 : setting incline
3) COUNT DOWN Mode
➢START / READY MODE
Press MODE : User can set TIME MODE  DISTANCE  CALORIES  MODE  P1...
 P5  BODYFAT  HRC in turn, t e setting mode value will blink.
➢TIME MODE
Preset timer is 20 minutes.
Press SPEED + / - : User can adjust target time ( 5 : 00 ~ 99 : 00 ).
Press START : Countdown 3 seconds and get into t e SPORT Mode ( times countdown).
➢DISTANCE MODE
Preset distance is 5 KM.
Press SPEED + / - : User can adjust target distance ( 1.0 KM ~ 99.0 KM ), step is 1 KM.
Press START : Countdown 3 seconds and get into t e SPORT Mode ( times count ).
➢CALORIES MODE
Preset is 200 Calories
Press SPEED + / - : User can adjust target calories ( 40 Calories ~ 999 Calories ), step is 1.
Press START : Countdown 3 seconds and get into t e SPORT Mode ( times count ).
➢PANEL WINDOW INDICATION
TIME / AGE : TIME MODE indicate (20:00), DISTANCE MODE indicate (0.00), CALORIES
MODE indicate (0:00).
CALORIES / INCLINE / SEX : TIME MODE indicate (0), DISTANCE MODE indicate (0),
CALORIES MODE indicate (200).
DISTANCE / HEIGHT : TIME MODE indicate (0.0), DISTANCE MODE indicate (5.0),
CALORIES MODE indicate (0.0).
SPEED : Indicate (0.0).
Pulse / WEIGHT : Indicate Heart Rate if no eart rate value indicate (P).
➢SPORT MODE
Press SPEED + / - : setting speed
Press INCLINE + / - : setting incline.
Press STOP / RESET : stop running , press STOP / RESET again, all value will delete to
zero and back to t e START / READY mode.
Press START : countdown 3 seconds and get into t e sport mode.
Press 3 / 6 / 9 : setting speed 3 / 6 / 9 KM / HR.
Press 3 / 6 / 9 : setting incline 3 / 6 / 9 %.
13

4) PROGRAM Mode
➢START / READY Mode
Press MODE : User can set TIME MODE  DISTANCE  CALORIES  MODE  P1...
 P5  BODYFAT  HRC in turn, t e setting mode value will blink.
Preset timer is 20 minutes.
Press SPEED + / - : User can adjust target time ( 5 : 00 ~ 99 : 00 ).
Press INCLINE + / - : User can adjust L1 ~ L5.
Press START : Countdown 3 seconds and get into t e SPORT Mode.
➢PANEL WINDOW INDICATION
TIME / AGE : Indicate (20:00)
DISTANCE : Indicate (0:00)
CALORIES / INCLINE / SEX : Indicate (0)
SPEED : Indicate L1 ~ L5.
Pulse / WEIGHT : Indicate Heart Rate if no Heart Rate value indicate (p).
Program : Indicate P1 ~ P5.
➢SPORT MODE
Press SPEED + / - : setting speed. Press INCLINE + / - : setting incline.
Press STOP / RESET : stop running , press STOP / RESET again, all value will delete to
zero and back to t e START / READY mode.
Press START : countdown 3 seconds and get into t e sport mode.
Press 3 / 6 / 9 : setting speed 3 / 6 / 9 KM / HR.
Press 3 / 6 / 9 : setting incline 3 / 6 / 9 %.
Eac segment time is setting time ÷ 20.
5) BODY FAT Mode
➢START / READY Mode
Press MODE : User can set TIME MODE  DISTANCE  CALORIES  MODE  P1...
 P5  BODYFAT  HRC in turn, t e setting mode value will blink.
Press ENTER : During BODY FAT Mode, user can set AGE  HEIGHT  SEX  WEIGHT
 into BODY FAT Mode.
Press SPEED + / - : User can
AGE : Preset is 30
HEIGHT : Preset is 170 cm, adjustable range is 130 cm ~ 200 cm.
SEX : Preset is Male (1), Female is (0).
WEIGHT : Preset is 70 KGS, adjustable range is 23 KGS ~ 130 KGS.
➢PANEL WINDOW INDICATION
TIME / AGE : Indicate AGE.
14

DISTANCE / HEIGHT : Indicate HEIGHT.
CALORIES / INCLINE / SEX : Indicate SEX.
SPEED : No Indicate.
Pulse / WEIGHT : Indicate WEIGHT.
➢BODY FAT Mode
After WEIGHT was setting, and it will detect eart rate, and Pulse display will s ow “----”,
10 seconds later Pulse display will s ow t e BODY FAT value.
After detected BODY FAT value, 10 seconds later back to START / READY Mode
automatically.
During detect t e BODY FAT, t ere is no function to press ENTER.
During detect t e BODY FAT, if no detect eart rate wit in 30 seconds, t e display will s ow
E4, press MODE or press STOP / RESET last 5 seconds, t en back to START / READY
Mode.
6) HRC Mode
➢START / READY Mode
Press MODE : User can set TIME MODE  DISTANCE  CALORIES  MODE  P1...
 P5  BODYFAT  HRC in turn, t e setting mode value will blink.
Press ENTER into t e HRC Mode. Press SPEED + / - : User can adjust AGE (13 ~ 80).
T en press ENTER into t e eart rate adjustment. Press SPEED + / - : User can adjust
eart rate target value.
It will detect eart rate c ange after 2 minutes later, eac 10 seconds detects one time. Eac time
it detects, it will increase / decrease speed 0.2 KM / HR. Incline will increase / decrease 1 degree,
after speed increases one time t e incline will increase one degree. If no eart rate is detected after
2 minutes later, t e display will s ow a warning sign and if no furt er eart rate is detected wit in t e
next 30 seconds; t e treadmill will stop running.
7) COOL DOWN Mode
➢SPORT MODE
Press COOL DOWN, into t e COOL DOWN Mode.
➢COOL DOWN Mode
Into t e COOL DOWN Mode, t e display will s ow COOL blinking and returns back to t e
original display after 3 seconds.
Countdown 4 minutes, t e running speed will decrease to alf, t e incline will reduce to 0,
eac 1 minute t at passes by; t e speed will again decrease to alf until t e time is over and
returns back to t e START / READY Mode.
Press STOP / RESET : STOP running, press STOP / RESET again, all values will delete and
return back to t e START / READY Mode.
15

8) OPERATION Mode
1) Turning on t e treadmill w ere all displays will s ow for 3 seconds and BEEP one time t en
transitioning into t e user WEIGHT setting mode.
2) General Mode : T e display will s ow MENU, t en press START.
3) Time Countdown Mode : After turning on t e treadmill, press MODE one time, t e time display
will blink; preset timer is 20 minutes, t en press SPEED FAST / SLOW will adjust target time
(5:00 ~ 99:00 minutes).
4) Distance countdown mode : After turning on t e treadmill press MODE twice time, distance
display will blink; preset distance is 5 Km, t en press SPEED FAST / SLOW will adjust target
distance (1.0 Km ~ 99.00 Km).
5) Calorie countdown mode : After turning on t e treadmill press MODE t ree times, t e calorie
display will blink; preset calorie is 200 calories, t en press SPEED FAST / SLOW will adjust
target calorie (40 calories ~ 999 calories).
6) PROGRAM mode : After turning on t e treadmill press MODE 4 ~ 8 times, t e time and display
will blink; preset countdown is 20 minutes, t en press SPEED +/- will adjust target time (5:00 ~
99:00 minutes), press INCLINE +/- to adjust t e level (L1 ~ L5).
9) LEVEL Mode
Eac increase of 1 LEVEL, t e speed is increased 0.5 KM / HR, incline is increased to 1 degree, all
is 5 LEVEL.
Under t e sport mode Calories / INCLINE display; t e preset s ows Calories, pressing ENTER can
switc c ange Calories / INCLINE.
SAFETY KEY / CLIP FUNCTION
During exercise, if t ere is any problem or accident please do not esitate to pull off t e safety key /
clip, t e treadmill will stop operation immediately.
10) SCALE
BEGINNING PRESET COUNTDOWN
VALUE
COUNTDOWN
SETTING
RANGE
TIME (min : sec) 0:00 20:00 5:00 ~ 99.00 0:00 ~ 99:59
SPEED (km / ) 1.0 N/A N/A 1.0 ~ 16.0 km / r
DISTANCE (km) 0.00 N/A 5.0 ~ 99.00 0.0 ~ 99.9
CALORIES (calories) 0 N/A 40 ~ 999 0 ~ 9999
PULSE (bpm) HP N/A N/A 40 ~ 220
16

11) PROGRAM
17

18