Horizon Fitness Adventure E User manual

TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
Adventure E

2

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises.
To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
WARNING
SERIAL NUMBER:
MODEL NAME: HORIZON TREADMILL

4
WATER BOTTLE HOLDER
GRIP PULSE HANDRAILS
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
POWER CORD
CONSOLE
IPOD/MP3 PLAYER POCKET
TOUCH PAD PANEL AND DISPLAY WINDOWS
SAFETY KEY PLACEMENT
MOTOR COVER
RUNNING BELT / RUNNING DECK
SIDE RAIL
ROLLER END CAP
REAR ROLLER
ADJUSTMENT BOLTS
CONSOLE MAST
FOOT LOCK LATCH (UNDERNEATH DECK)
SUPPORT BAR

5
TOOLS INCLUDED:
6 mm T-Wrench
5 mm L-Wrench
4 mm T-Wrench
4 mm L-Wrench
PARTS INCLUDED:
1 Console Assembly
2 Console Masts
2 Socket
1 Support Bar
5 Hardware Bags
1 Safety Key
1 Bottle of Silicone Lubricant
(for 2 applications)
1 Power Cord
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You
may remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place
a protective covering on your floor. Take CAUTION when handling and transporting
this unit. Never open box when it is on its side. Once the banding straps have been
removed, do not lift or transport this unit unless it is fully assembled and in the upright
folded position, with the lock latch secure. Unpack the unit where it will be used. The
enclosed treadmill is equipped with high-pressure shocks and may spring open if
mishandled. Never grab hold of any portion of the incline frame and attempt to lift or
move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
PRE ASSEMBLY

6
ASSEMBLY STEP 1
A Open HARDWARE BAG 1.
B Cut the yellow banding and get console mast
out
C Attach the LEFT SOCKET (1) to the LEFT
CONSOLE MAST (2) using 4 SOCKET BOLTS
(A).
D Attach the RIGHT SOCKET (3) to the RIGHT
CONSOLE MAST (4) using 4 SOCKET BOLTS
(A).
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
ASOCKET BOLT M6X1.0PX10L 8
1
2 4
3
A

7
ASSEMBLY STEP 2
A Lift the RUNNING DECK (5) upward until
the FOOT LATCH (6) locks. Remove all
contents from underneath the running
deck.
B Open HARDWARE BAG 2.
C With the RUNNING DECK (5) in the raised
position, attach the LEFT CONSOLE
MAST (2) to the BASE FRAME (7) using 4
BOLTS (B), 4 SPRING WASHERS (C) and
4 FLAT WASHERS (D).
HARDWARE FOR STEP 2
PART TYPE DESCRIPTION QTY
BBOLT M8X1.25PX20L 4
CSPRING WASHER Φ8.2xΦ15.4x2.0T 4
DFLAT WASHER Φ8.4xΦ15.5x1.6T 4
2
5
6
7
D
C
B

8
ASSEMBLY STEP 3
A Open HARDWARE BAG 3.
B Pull LEAD WIRE (8) through RIGHT
CONSOLE MAST (4). After pulling the
lead wire through the mast, the top of the
CONSOLE CABLE (9) should be located
at the top of the mast. Detach and discard
the lead wire.
C With the RUNNING DECK (5) in the raised
position, attach the RIGHT CONSOLE
MAST (4) to the BASE FRAME (7) using
4 BOLTS (B), 4 SPRING WASHERS (C)
and 4 FLAT WASHERS (D).
NOTE: Be careful not to pinch any wires while
assembling the right console mast.
HARDWARE FOR STEP 3
PART TYPE DESCRIPTION QTY
BBOLT M8X1.25PX20L 4
CSPRING WASHER Φ8.2xΦ15.4x2.0T 4
DFLAT WASHER Φ8.4xΦ15.5x1.6T 4
D
C
B
5
9
9
7
8
4

9
ASSEMBLY STEP 4
A Disengage the DECK LOCK LATCH with
your foot to lower the RUNNING DECK.
B Open HARDWARE BAG 4.
C Gently place the CONSOLE (10) on top of
the CONSOLE MASTS. Attach the LEFT
SIDE first using 3 BOLTS (E), 3 SPRING
WASHERS (C) and 3 FLAT WASHERS
(D).
D Connect the CONSOLE CABLES (9),
carefully tucking wires in masts to avoid
damage.
E Attach the RIGHT SIDE of the CONSOLE (10)
using 3 BOLTS (E), 3 SPRING WASHERS (C)
and 3 FLAT WASHERS (D).
NOTE: Be careful not to pinch any wires while
assembling the masts.
HARDWARE FOR STEP 4
PART TYPE DESCRIPTION QTY
CSPRING WASHER Φ8.2xΦ15.4x2.0T 6
DFLAT WASHER Φ8.4xΦ15.5x1.6T 6
EBOLT M8X1.25PX15L 6
9
10
D
C
E
ASSEMBLE
LEFT SIDE
FIRST

10
ASSEMBLY STEP 5
A Open HARDWARE BAG 5.
B Align SUPPORT BAR (11) with holes in
CONSOLE MASTS.
C Insert BOLTS (F) into all 4 holes of the
SUPPORT BAR (11).
F Tighten all console bolts (Step 4)
and support bar bolts (Step C above)
completely
NOTE: Look into holes in the right mast
before inserting bolts to avoid pinching
cables.
HARDWARE FOR STEP 5
PART TYPE DESCRIPTION QTY
FBOLT M6X1.0PX15L 4
F
11