Bosch NPD-6001A User manual

High PoE Midspan 60W, Sin-
gle port, AC in
NPD-6001A
en Installation Manual

Table of contents
1Safety 4
1.1 Conventions in this Manual 4
1.2 About this Manual 5
1.3 Important Safety Instructions 5
1.4 Customer Support and Service 7
2Unpacking 9
2.1 Parts List 9
2.2 Additional Parts Required 9
2.3 Tools Required 10
2.4 Additional Parts Recommended But Not Required 10
3System overview 11
4Installation 12
5Connection 14
6Troubleshooting 16
High PoE Midspan 60W,
Single port, AC in Table of Contents | en 3
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Safety
Conventions in this Manual
In this manual, the following symbols and notations are used to
draw attention to special situations:
Danger!
This symbol indicates an imminently hazardous situation such as
“Dangerous Voltage” inside the product. If not avoided, this will
result in an electrical shock, serious bodily injury, or death.
!
Warning!
Indicates a potentially hazardous situation. If not avoided, this
could result in serious bodily injury or death.
!
Caution!
Medium Risk
Indicates a potentially hazardous situation. If not avoided, this
may result in minor or moderate injury. Alerts the user to impor-
tant instructions accompanying the unit.
!
Caution!
Indicates a potentially hazardous situation. If not avoided, this
may result in property damage or risk of damage to the unit.
i
Notice!
This symbol indicates information or a company policy that re-
lates directly or indirectly to the safety of personnel or protec-
tion of property.
1
1.1
4en | Safety High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

About this Manual
This manual has been compiled with great care and the
information it contains has been thoroughly verified. The text
was complete and correct at the time of printing. Because of the
ongoing development of products, the content of the manual
may change without notice. Bosch Security Systems accepts no
liability for damage resulting directly or indirectly from faults,
incompleteness, or discrepancies between the manual and the
product described.
Important Safety Instructions
Read, follow, and retain for future reference all of the following
safety instructions. Heed all warnings on the unit and in the
operating instructions before operating the unit.
– The unit is intended only for installation in a Restricted
Access Location.
– Installation and removal of the midspan must be carried out
by qualified personnel only.
– Follow basic electricity safety measures whenever
connecting the midspan to its power source.
–AC Power Cord Set: Although the High PoE Midspan 60W,
Single port ships with one (1) 120 V power cord and one
(1) 230 V power cord, please note the following as it
applies to your region:
– The power cord must have regulatory agency approval
for the specific country in which it is being used (i.e.,
UL, CSA, VDE, etc.).
– The power cord must be a three-conductor type (two
current carrying conductors; one ground conductor)
terminated on one end by an IEC 60320 appliance
coupler (for connection to the midspan), and on the
other end by a plug containing a ground (earthing)
contact.
1.2
1.3
High PoE Midspan 60W,
Single port, AC in Safety | en 5
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

– The power cord must be rated for a minimum of 250
VAC RMS operation, with a minimum rated current
capacity of 5 Amps (or a minimum wire gauge of 18
AWG (0.75mm2).
– Midspans installed in Australia require power cords
with a minimum wire gauge of 16 AWG (1.0 mm2).
– A voltage mismatch can cause equipment damage and may
pose a fire hazard. If the voltage indicated on the label is
different from the power outlet voltage, do not connect the
midspan to this power outlet.
– The AC wall socket-outlet must be near the midspan and
easily accessible. You can remove AC power from the
midspan by disconnecting the AC power cord from either
the wall socket-outlet or the midspan appliance coupler.
– The PoE injector "Data In" and "Data & Power Out" ports
are shielded RJ45 data sockets. They cannot be used as
Plain Old Telephone Service (POTS) telephone sockets.
Only RJ45 data connectors can be connected to these
sockets.
– The Data In and Data & Power Out interfaces are qualified
as SELV (Safety Extra-Low Voltage) circuits according to
IEC 60950-1. These interfaces can only be connected to
SELV interfaces on other equipment.
Recycling and Disposal:
6en | Safety High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

Your Bosch product was developed and manufactured with high-
quality material and components that can be recycled and
reused. This symbol means that electronic and electrical
appliances, which have reached the end of their working life,
must be collected and disposed of separately from household
waste material. Separate collecting systems are usually in place
for disused electronic and electrical products. In the United
States, please dispose of these units at your local communal
waste collection point or at a recycling center. In the EU, please
dispose of these units at an environmentally compatible
recycling facility, per European Directive 2002/96/EC.
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security
Systems Service Center for authorization to return and shipping
instructions.
Service Centers
USA
Repair Center
Telephone: [phone] / Fax: [phone]
E-mail: [email protected]
Customer Service
Telephone: [phone] / Fax: [phone]
E-mail: [email protected]
Technical Support
Telephone: [phone] / Fax: [phone] or 717-735-6560
E-mail: [email protected]
Canada
Telephone: [phone] / Fax: [phone]
Europe, Middle East, Africa Region
Repair Center
Telephone: [phone] / Fax: [phone]
E-mail: [email protected]
Asia Region
Repair Center
1.4
High PoE Midspan 60W,
Single port, AC in Safety | en 7
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Telephone: [phone] / Fax: [phone]
E-mail: [email protected]
Customer Service
Telephone: [phone] or 86 (0) 756 7633121 / Fax: 86
(0) 756 7631710
E-mail: [email protected]
Warranty and additional information
For additional information and warranty queries, please contact
your Bosch Security Systems representative or visit our website
at www.boschsecurity.com.
8en | Safety High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

Unpacking
Parts List
The package containing the High PoE Midspan 60W, Single port
should include the following items:
Quantity Part
1 High PoE Midspan 60W, Single port, AC in
1 120 V power cord
1 230 V power cord
1 Installation Manual (this document)
Additional Parts Required
The following table lists additional parts (not supplied by
Bosch) required to install the midspan:
Quantity Part Size Notes
2 Mounting
screws;
Select either
size
(but not both).
Head diameter:
5.8 mm
(0.23 in.)
1.5 mm (0.059 in.)
clearance from mounting
surface
Head diameter:
7 mm
(0.27 in.)
Head height:
2 mm
(0.08 in.)
2.5 mm (0.098 in.)
clearance from mounting
surface
2 CAT5 cables Not to exceed
100 m (333 ft)
each
1 cable to connect to the
“Data & Power
Out“ port.
1 cable to connect to the
“Data In” port.
2
2.1
2.2
High PoE Midspan 60W,
Single port, AC in Unpacking | en 9
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Tools Required
Screwdriver
Additional Parts Recommended But Not
Required
The following table lists additional parts (not supplied by
Bosch) recommended to install the midspan:
Quantity Part
1 Surge suppressor
1 Splitter
1 Universal Power Supply (UPS)
2.3
2.4
10 en | Unpacking High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

System overview
The High PoE Midspan 60W, Single port, AC in is a high-power
PoE (Power over Ethernet) device that provides power over
Ethernet cabling between an Ethernet (remote network) switch
and an AutoDome 7000 Series camera. It supports the
IEEE802.3at and IEEE802.3af standards, while doubling the
output power to 60 W. The midspan is designed to carry gigabit
Ethernet data and power over a standard CAT5e cable, delivered
through all 4 pairs:
– Alt A: pin 1,2 (-) and 3,6 (+)
– Alt B: 4,5 (+) and 7.8 (-)
Note: Do NOT use cross-over cable between the Data & Power
Out port and the AutoDome camera!
Note: The midspan is not a repeater and does not amplify the
Ethernet data signal.
Note: The Ethernet cable length must be less than 100 meters
from the Ethernet source to the AutoDome camera.
3
High PoE Midspan 60W,
Single port, AC in System overview | en 11
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Installation
!
Caution!
Installation must be made by qualified personnel and conform
to ANSI/NFPA 70 (the National Electrical Code® (NEC)), Canadi-
an Electrical Code, Part I (also called CE Code or CSA C22.1),
and all applicable local codes. Bosch Security Systems, Inc. ac-
cepts no liability for any damages or losses caused by incorrect
or improper installation.
The midspan can be placed on a desktop or mounted on a wall,
bench, or shelf using the rear side mounting holes.
Before mounting the midspan to a fixed location, note the
following:
– Do not cover the midspan or block the airflow to the PoE
with any foreign objects.
– Keep the midspan away from excessive heat and humidity
and free from vibration and dust.
– Ensure that the cable length from the Ethernet network
source to the terminal does not exceed 100 meters (333
feet). The midspan is not a repeater and does not amplify
the Ethernet data signal.
– No “on-off” switch exists; simply plug the midspan into an
AC power source.
Installing the Unit
Follow these steps in sequence to install the Bosch midspan.
1. Select the mounting location and surface. Ensure that the
selected surface will be able to support the weight of the
unit (400 g / 0.88 lb). Note that this unit is intended only
for installation in a Restricted Access Location.
2. Install two mounting screws in the selected mounting
surface, at a distance of 9.17 mm (3.61 in.) apart from the
center of each screw.
3. Align the mounting slots on the unit to the screws.
4. Proceed to the Connection chapter.
4
12 en | Installation High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

High PoE Midspan 60W,
Single port, AC in Installation | en 13
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Connection
i
Notice!
The PoE ports “Data In“ and “Data & Power Out“ are shielded
RJ45 data sockets. They cannot be used as “Plain Old Tele-
phone Service” (POTS) telephone sockets. Connect only RJ45
data connectors (EIA 568A and 568B) to these ports.
The “Data In” and “Data & Power Out” interfaces are qualified
as “Safety Extra Low Voltage” (SELV) circuits according to IEC
60950-1. These interfaces can be connected only to SELV inter-
faces on other equipment.
1. Connect the midspan to an AC power outlet (100 – 240
VAC), using one of the two power cords supplied, or one
that has the appropriate ratings and specifications (see the
Safety chapter).
Note: The voltage of the power outlet must match the
voltage indicated on the midspan label.
2. Connect the Data In (input) port to the remote Ethernet
network switch.
3. Connect the Data & Power Out (output) port to the
Ethernet port on the AutoDome camera.
Note: Do NOT use cross-over cable!
5
14 en | Connection High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

Figure 5.1: Midspan_DataIn_DataOut_Connections
1AC input connectivity indicator
2 Port connectivity indicator
3 CAT5 cable
4 Connection to AutoDome camera
5 Connection to Ethernet switch
4If desired, connect a splitter close to the terminal, but not
on the midspan.
High PoE Midspan 60W,
Single port, AC in Connection | en 15
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Troubleshooting
LED Indicators
The following tables identify the indicators on the top of the
midspan.
AC LED OFF Green
Green Power off indicator Power on indicator
(power is active)
Port LED Behavior
– OFF – No detection or disconnected no
load is connected.
– Yellow ON – Power supplied over data or spare
– Green ON – Power supplied over data and spare
pairs together
– Blinking yellow
at 1Hz rate
– Over current or short circuit
condition at one of the 2 pairs (the
other pair is OFF) - data or spare,
(PD or cable fault)
– Blinking yellow
and green
at 1Hz rate
– Over current or short circuit
condition at one or both pairs - data
or/and spare, (PD or cable fault)
– Blinking yellow
or green 4Hz
rate
– Internal fault condition
6
16 en | Troubleshooting High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

Troubleshooting Steps
Symptom Corrective Steps
– The
midspan
does not
power up.
1. Verify that a reliable power cord is used.
2. Verify that the voltage at the power inlet
is between 100 and 240 VAC.
3. Remove and re-apply power to the device
and then check the indicators during power
up sequence.
– The
midspan
does not
operate, but
no port
indicator is
lit.
1. Verify that the midspan detects the
camera.
2. Verify that you are using a standard
Category 5/5e/6, straight-wired cable, with
four pairs.
3. If an external power splitter is used,
replace it with a splitter known to operate.
4. Verify that the input Ethernet cable is
connected to the Data In port.
5. Verify that the AutoDome camera is
connected to the Data & Power Out port.
6. Try to reconnect the camera to a different
midspan. If the camera works, then there is
probably a faulty port or RJ45 connection
on the midspan.
7. Verify that there is not a short over any of
the twisted pair cables or over the RJ45
connectors.
– The
AutoDome
camera
operates,
but there is
no data link.
1. Verify that the port indicator on the front
panel is continuously lit.
2. If an external power splitter is used,
replace it with a splitter known to operate.
3. Verify that for this link, you are using
standard UTP/FTP Category 5 straight (non-
crossover) cabling, with all four pairs.
High PoE Midspan 60W,
Single port, AC in Troubleshooting | en 17
Bosch Security Systems Installation Manual 2013.03 | 1.2 | F.01U.279.929

Symptom Corrective Steps
4. Verify that the Ethernet cable length is
less than 100 meters from the Ethernet
source to the AutoDome camera.
5. Try to reconnect the camera to a different
midspan. If the camera works, then there is
probably a faulty port or RJ45 connection
on the midspan.
18 en | Troubleshooting High PoE Midspan 60W,
Single port, AC in
2013.03 | 1.2 | F.01U.279.929 Installation Manual Bosch Security Systems

Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA, 17601
USA
www.boschsecurity.com
© Bosch Security Systems, Inc., 2013