Bosch Rexroth IndraControl XFE01.1-SY-01 User manual

IndraControl
XFE01.1-SY-01
Safety Extension Module
Operating Instructions
R911376654
Edition 04

IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Change Record
Edition 04
2021-09
See tab. 1-1 "Change record" on page 1
Copyright
© Bosch Rexroth AG 2021
All rights reserved, also regarding any disposal, exploitation, reproduction, edit-
ing, distribution, as well as in the event of applications for industrial property
rights.
Liability
The specified data is intended for product description purposes only and shall
not be deemed to be a guaranteed characteristic unless expressly stipulated in
the contract. All rights are reserved with respect to the content of this documen-
tation and the availability of the product.
Editorial Department
Engineering Automation Systems Solution Integration PLC, Safety and Control
HW HaBu, AnSt (MaKo/MePe)
RS-62b285c6a15c540c0a347ea5011f663a-4-en-US-7

Table of Contents
Page
1 About this documentation..................................................................... 1
1.1 Overview on target groups and product phases.................................... 1
1.2 Purpose................................................................................................. 2
1.3 Qualifications......................................................................................... 2
1.4 Scope..................................................................................................... 2
1.5 Related documents................................................................................ 2
1.6 Customer feedback................................................................................ 3
2 Product identification and scope of delivery......................................... 3
2.1 Product identification............................................................................ 3
2.2 Product identification............................................................................ 4
2.3 Scope of delivery................................................................................... 4
3 Using safety instructions....................................................................... 4
3.1 Structure of the safety instructions....................................................... 4
3.2 Explaining signal words and safety alert symbol................................... 5
3.3 Symbols used........................................................................................ 6
3.4 Explaining the signal alert symbol on the device................................... 6
4 Intended use.......................................................................................... 6
5 Spare parts and accessories.................................................................. 8
5.1 Accessories............................................................................................ 8
5.2 Wear parts............................................................................................. 8
6 Ambient conditions................................................................................ 8
7 Technical data...................................................................................... 12
7.1 Voltage supply...................................................................................... 12
7.2 Safety-related characteristic values..................................................... 12
7.3 Dimensions and weight....................................................................... 13
8 Standards............................................................................................ 13
8.1 Standards used.................................................................................... 13
8.1.1 General standards............................................................................... 13
8.1.2 Safety standards.................................................................................. 14
8.2 TÜV certificate..................................................................................... 15
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
I
Table of Contents
R911376654_Edition 04 Bosch Rexroth AG

Page
8.3 CE marking.......................................................................................... 16
8.3.1 Declaration of conformity.................................................................... 16
8.4 UL/CSA certified.................................................................................. 16
9 Interfaces............................................................................................. 17
9.1 Connection position............................................................................ 17
9.2 SD card slot......................................................................................... 18
10 Mounting, dismounting and electric installation.................................. 19
10.1 Housing dimensions............................................................................. 19
10.2 Installation notes................................................................................. 19
10.3 Mounting.............................................................................................. 21
10.4 Dismounting......................................................................................... 22
10.4.1 Dismounting steps............................................................................... 22
10.5 Electric installation.............................................................................. 23
10.5.1 External power supply unit ................................................................. 24
10.5.2 Voltage supply for the control and for the extension modules............ 24
10.5.3 24 V voltage supply.............................................................................. 25
10.5.4 Grounding
............................................................................................................. 26
10.5.5 Shielding.............................................................................................. 27
11 Commissioning.................................................................................... 27
11.1 General information............................................................................. 27
11.2 IT security............................................................................................ 28
12 Device description............................................................................... 29
12.1 SD card................................................................................................ 30
12.2 Operating and error displays............................................................... 30
12.2.1 "Conf" pushbutton............................................................................... 30
12.2.2 LED...................................................................................................... 30
12.2.3 LED on XD1 plug.................................................................................. 32
13 Troubleshooting and debugging........................................................... 32
13.1 General information............................................................................. 32
14 Maintenance........................................................................................ 32
14.1 Cleaning notes..................................................................................... 33
14.2 Maintenance notes............................................................................... 33
II
Table of Contents
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

Page
14.3 Replacing SD card............................................................................... 33
15 Ordering information........................................................................... 34
15.1 Type code............................................................................................. 34
15.2 Accessories and spare parts................................................................ 35
15.3 Ordering data ...................................................................................... 35
16 Disposal............................................................................................... 35
16.1 General information............................................................................. 35
16.2 Return.................................................................................................. 35
16.3 Packaging............................................................................................. 35
17 Service and support............................................................................ 35
Index.................................................................................................... 37
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
III
Table of Contents
R911376654_Edition 04 Bosch Rexroth AG

IV IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

1 About this documentation
Editions of this documentation
Edition Release
date
Note
Edition 01 2016-10 First edition
Edition 02 2017-06 Chapter "Safety standards" revised, new chapter "Ordering data", stand-
ards and warning instructions modified for UL
Edition 03 2019-05 References supplemented
Edition 04 2021-09 Standards updated
Tab. 1-1: Change record
1.1 Overview on target groups and product phases
In the following illustration, the framed activities, product phases and target
groups refer to the present documentation.
Example: In the product phase "Mounting (assembly/installation)", the "mechan-
ic/electrician" can execute the activity "unpack, mount and install"using this
documentation.
Presales Aftersales
Selection Mounting
(assembly/installation)
Engineering Commissioning Operation Decommissioning
Product
phases
Target
groups
Activities
Design engineer
Programmer
Technologist
Process
specialist
Select
Prepare
Design
Construct
Mechanic/
electrician
Unpack
Mount
Install
Programmer
Commissioning engineer
Parameterize
Program
Configure
Simulate
Technologist
Process specialist
Optimize
Test
Machine
operator
Maintenance
technician
Service
Operate
Maintain
Remove
faults
Create
the NC program
Mechanic/
electrician
Disposal company
Dismount
Dispose
Fig. 1-1: Assigning the present documentation to the target groups, product phases and ac-
tivities of the target group
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
1/41
About this documentation
R911376654_Edition 04 Bosch Rexroth AG

1.2 Purpose
This operating instructions provides information on the safe mounting and the
electric installation of the Safety extension module IndraControl XFE01.1-SY-01
to the technical employees of the machine manufacturer or the machine opera-
tor. This documentation does not provide instructions on the operation of the
machine into which the Safety extension module IndraControl XFE01.1-SY-01 is
or will be integrated. The operating instructions of the machine contains the in-
formation.
1.3 Qualifications
Required qualification: Individual who is able to assess the tasks assigned and to
identify possible safety risks owing to qualification in the subject, knowledge
and experience. The individual should also be familiar with the standards and
regulations.
1.4 Scope
This operating instruction applies to the Safety extension module with the type
code "XFE01.1-SY-01".
For the type code specifications, refer to chapter 15 "Ordering information" on
page 34.
1.5 Related documents
Title Description
IndraWorks 14VRS
SafeLogic
Project Configuration
R911341694
Application Description
This documentation is intended as guideline when creating a
safety-related application
IndraWorks
SafeLogic 14VRS
First Steps
R911341520
Commissioning Manual
This documentation contains descriptions about the follow-
ing topics:
●Creation and use of a safety application
●Basics of the data exchange between the safety applica-
tion and the standard application of the IndraLogic XLC/
IndraMotion MLC/IndraMotion MTX 14VRS
●Information on diagnostics and troubleshooting
●Programming under SafeLogic
2/41
About this documentation
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

Title Description
IndraLogic XLC
IndraMotion MLC 14VRS
SafeLogic System Overview
R911341696
Project Planning Manual
This documentation describes the project planning of safety-
related devices in the systems IndraLogic XLC and
IndraMotion MLC
IndraControl
XM2x
Controls
R911340667
Operating Instructions
This operating instructions instructs the technical staff of the
machine manufacturer on a safe mechanical and electrical
mounting and commissioning
IndraControl
XM4
Controls
R911345566
Operating Instructions
This operating instructions instructs the technical staff of the
machine manufacturer on a safe mechanical and electrical
mounting and commissioning
IndraControl VAP 01
Power Supply Unit
R911339613
Operating Instructions
This document instructs the technical staff of the machine
manufacturer on how to perform the mechanical and electri-
cal installation safely and on how to commission it at the
power supply unit
Tab. 1-2: Related documents
If a documentation is not available, please contact the Bosch
Rexroth Service.
1.6 Customer feedback
Customer requests, comments or suggestions for improvement are of great im-
portance to us. Please email your feedback on the documentations to Feed-
[e-mail]. Directly insert comments in the elec-
tronic PDF document and send the PDF file to Bosch Rexroth.
2 Product identification and scope of deliv-
ery
2.1 Product identification
The Safety extension module IndraControl XFE01.1-SY-01 is connected to the
left-handed extension bus of the control connected. The lower part of the hous-
ing of the extension module IndraControl XFE01.1-SY-01 is grey, the upper part
of the housing is yellow.
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
3/41
Product identification and scope of delivery
R911376654_Edition 04 Bosch Rexroth AG

The type code is attached as label on the side of the lower part of the housing
of the Safety extension module IndraControl XFE01.1-SY-01.
2.2 Product identification
1Word mark
2Part number
3State of revision
4Type name (type code)
5Plant number
6Serial number
7Rexroth bar code
8Manufacturing date (yyWww)
9QR code
10 Check digit
11 Nominal current
12 Nominal voltage
13 Manufacturing country
14 Company address
15 Certification stamp TÜV-Rheinland
16 CE conformity marking
17 Graphic symbol of the equipment
Fig. 2-1: Exemplary type plate
2.3 Scope of delivery
●Safety extension module IndraControl XFE01.1-SY-01
●24 V power connector XA-CN01
●Bus base module XA-BS11 for IndraControl extension modules
●Safety instructions
3 Using safety instructions
3.1 Structure of the safety instructions
The safety instructions are structured as follows:
4/41
Using safety instructions
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

Burns and chemical burns due to wrong
battery treatment!
CAUTION
Safety alert symbol
Signal word
Avoiding danger
Do not open the batteries and do not heat them over 80 °C.
Consequences and
source of danger
Fig. 3-1: Structure of the safety instructions
3.2 Explaining signal words and safety alert symbol
The safety instructions in this documentation contain specific signal words
(danger, warning, caution, notice) and, if necessary, a safety alert symbol
(according to ANSI Z535.6-2006).
The signal word draws attention to the safety instruction and indicates the risk
potential.
The safety alert symbol (triangular safety reflector with exclamation marks),
preceding the signal words Danger, Warning, Caution indicates hazards for
persons.
DANGER
In case of non-compliance with this safety instruction, death or serious injury
will occur.
WARNING
In case of non-compliance with this safety instruction, death or serious injury
can occur.
CAUTION
In case of non-compliance with this safety instruction, minor or moderate injury
can occur.
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
5/41
Using safety instructions
R911376654_Edition 04 Bosch Rexroth AG

NOTICE
In case of non-compliance with this safety instruction, material damage can
occur.
3.3 Symbols used
Pointers are displayed as follows:
This is a note.
Tips are displayed as follows:
This is a tip.
3.4 Explaining the signal alert symbol on the device
krax
If this symbol is on your device, you have to observe the documentation
on the device. The respective documentation informs on the type of
hazard as well as the steps required to avoid this hazard.
4 Intended use
The Bosch Rexroth Safety extension module IndraControl XFE01.1-SY-01 is a
safety component. It becomes only a safety-related control system (IndraMotion
MLC SafeLogic) if used with a Rexroth IndraControl XM control. For information
on the hardware of the IndraMotion MLC SafeLogic, refer to the documentation
of the hardware used (refer to chapter 1.5 "Related documents" on page 2).
The Safety extension module IndraControl XFE01.1-SY-01 is used to securely
process logic signals of periphery components (sensors) according to the se-
quential program and to provide logic signals for periphery components (actua-
tors). The sequential program can be freely programmed using the Engineering
system. Even though the control system was developed, manufactured and tes-
ted according to the safety standards and certified by an accredited test insti-
tute, using this component does not automatically ensure a functionally safe ma-
chine. The machine manufacturer has to perform a risk analysis and take corre-
sponding protective measures to reduce risks and to validate their effect even
though it was accredited and developed according to the safety standards. The
functional safety can only be ensured by comprehensively implementing the re-
quirements (e.g. systematic measures, software requirements, integrating the
sensors and actuators) according to the applicable standards (DIN EN ISO
13849, DIN EN 62061 and DIN EN 61131-6).
6/41
Intended use
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

Risk of damaging the Safety extension module if
not expressly stated accessories, mounting
parts and other components, cables, lines and
software and firmware are used
NOTICE
The Safety extension module IndraControl XFE01.1-SY-01 may only be used as
intended and combined with the accessories and attachments specified in this
documentation. Components that are not expressly mentioned must neither be
attached nor connected. It is strictly prohibited to change and operate compo-
nents (individual parts) as well as using firmware that is not permitted.
The Safety extension module IndraControl XFE01.1-SY-01 may only be operated
under the mounting, installation and ambient conditions (such as temperature,
protection class, humidity, EMC) specified in this documentation. Also refer to
chapter 6 "Ambient conditions" on page 8.
A typical area of application of the Safety extension module IndraControl
XFE01.1-SY-01 is the implementation of safety-related controls for:
●Handling and mounting systems
●Food and packaging machines
●Printing and processing machines
●Machine tools
●Compactors
●Foundry and rolling technology
●Conveying engineering
●Building automation
●Special purpose machines
●Wood processing machines
●Hydraulic machines
The operation is not permitted for the following systems according to the follow-
ing standards and guidelines:
●Lifts (directive 2006/42/EC)
●ATEX (directive 2014/34/EU)
●Burner control systems (DIN EN 298)
●Safety systems for unfired pressure vessels (DIN EN 764-7:2002/AC:2006)
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
7/41
Intended use
R911376654_Edition 04 Bosch Rexroth AG

5 Spare parts and accessories
5.1 Accessories
Type code Product description Part number
XA-CN01 24 V plug R911173741
XA-BS11 Bus base module for IndraControl extension
modules
R911173772
SUP-M01-ENDHALTER 2 pieces of snap-on end brackets for 35 mm
NS 35/7.5 or NS 35/15 carrier plate; width:
9.5 mm
R911170685
MICRO SD 1GB SD card 1070924212
Tab. 5-1: Ordering data for accessories
5.2 Wear parts
The Safety extension module has no wear parts.
6 Ambient conditions
In operation Storage and transport
Area of application Only in interior spaces –
Ambient temperature of the
control
+5 °C to +55 °C -40 °C to +85 °C
Relative humidity 10% to 95%, condensing not permitted 10% to 95%, condensing not
permitted
Contamination level 2 acc. to DIN EN 61131-2 2 acc. to DIN EN 61131-2
Air pressure and
Operating altitude
86 kPa to 106 kPa
(up to 2,000 m above sea level)
55 kPa to 106 kPa
(Up to 4,700 m above sea lev-
el)
Degree of protection IP 20 acc. to DIN EN 60529 IP 20 acc. to DIN EN 60529
Warning if internal tempera-
ture is low
≤ 5 °C –
Switch-off if internal tempera-
ture is low
≤ 1 °C –
Warning if internal tempera-
ture is high
≥ 86 °C –
Switch-off if internal tempera-
ture is high
≥ 89 °C –
Overvoltage category II –
Protection class III, DIN EN 61010-2-201 –
Tab. 6-1: Climatic ambient conditions and characteristics
8/41
Ambient conditions
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

In operation Storage and transport
Mounting position It is specified by the control –
Sinusoidal vibrations 5 Hz ≤ f ≤ 9 Hz: 3.5 mm amplitude
9 Hz ≤ f ≤ 150 Hz: 5.0 g
Acc. to DIN EN 60068-2-6
–
Shock stress 30 g peak value, period of 11 ms
Acc. to DIN EN 60068-2-27
–
Noise-induced oscillation – 10 Hz to 200 Hz with 1
(m/s2) 2/Hz
200 Hz to 1,500 Hz with 0.3
(m/s2) 2/Hz
Crest factor = 3
Tab. 6-2: Mechanic ambient conditions and characteristics
In operation
Emitted interference of the housing
Test acc. to DIN EN 55016
30 MHz to 230 MHz: 40 dB (μV/m) Q
230 MHz to 1000 MHz: 40 dB (μV/m) Q
Emitted interference of the mains con-
nection
Test acc. to DIN EN 55016
0.15 MHz to 0.5 MHz: 79 dB (μV) Q, 66 dB (μV) M
0.5 MHz to 30 MHz: 73 dB (μV) Q, 60 dB (μV) M
Tab. 6-3: Electromagnetic operating conditions: Testing noise emission acc. to EN 61000-6-4
In operation
ESD standard
Test acc. to DIN EN 61000-4-2
Air discharge up to ±8 kV, criterion A
Contact discharge up to ±4 kV, criterion A
ESD
Increased noise level
Air discharge up to ±8 kV, criterion FS
Contact discharge up to ±6 kV, criterion FS
Electromagnetic HF field standard
Test acc. to DIN EN 61000-4-3
80 MHz – 1,000 MHz: 10 V/m
1.4 GHz – 2.0 GHz: 3 V/m
2.0 GHz – 2.7 GHz: 1 V/m
Electromagnetic HF field
Increased noise level
80 MHz – 1,000 MHz: 20 V/m
1.4 GHz – 2.0 GHz: 10 V/m
2.0 GHz – 2.7 GHz: 3 V/m
Fast transients (burst), standard
Test acc. to DIN EN 61000-4-4
Affected interfaces 1 kV
Supply voltage 2 kV
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
9/41
Ambient conditions
R911376654_Edition 04 Bosch Rexroth AG

In operation
Fast transients (burst)
Increased noise level
Affected interfaces 2 kV
Supply voltage 4 kV
Surge, standard
Test acc. to DIN EN 61000-4-5
Asymmetric coupling:
0.5 kV (supply lines)
1 kV (signal/data lines)
Symmetric coupling:
0.5 kV (supply lines)
Surge
Increased noise level
Asymmetric coupling:
2 kV (supply lines)
2 kV (signal and data lines)
Symmetric coupling:
1 kV (supply lines)
HF coupling to lines
Test acc. to DIN EN 61000-4-6
0.15 MHz to 80 MHz: 10 Veff, criterion A
HF coupling to lines
Increased noise level
0.15 MHz to 80 MHz: 20 Veff, criterion FS
Voltage dips, short interruptions and
voltage fluctuations at DC mains inputs
Test acc. to DIN EN 61000-4-29
DC 24 V supply voltage: 20 interruptions every 10 s, inter-
ruption period of 10 ms
Voltage dips, short interruptions and
voltage fluctuations at DC mains inputs
Increased requirements
DC 24 V supply voltage:
1. 40% UT (rated voltage) for 10 ms
2. 0% UT (rated voltage) for 20 ms
Voltage deviation of -15 % to +20 %
3 attempts, period of 10 s
Tab. 6-4: Electromagnetic operating conditions: Testing electromagnetic compatibility acc.
to EN 61000-6-2 as well as increased noise level acc. to EN 61326-3-1
In case of overheating, the Safety extension
module IndraControl XFE01.1-SY-01 goes into a
safe
NOTICE
Provide sufficient ventilation and cooling to ensure that the ambient temperature
of the control does not exceed 55°C.
10/41
Ambient conditions
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

Due to the ambient conditions required to oper-
ate the Safety extension modules, the following
restrictions result for the entire system
NOTICE
●The operating height of the entire system is reduced from 4700 m to 2000 m
●The ambient temperature of the entire system in operation reduces from the
range between -25°C and +60°C to the range between + 5°C and +55°C
Defective product due to gases jeopardizing
functions
NOTICE
Due to the risk of corrosion, avoid sulphurous gases (e.g. sulphur dioxide (SO2)
and hydrogen suphide (H2S)). The product is not resistant against these gases.
Failure of the product due to contaminated air
NOTICE
●The ambient air must not contain acids, alkaline solutions, corrosive agents,
salts, metal vapors and other electrically conductive contaminants in high
concentrations
●The devices to be installed into the housing and installation compartments
must at least comply with the degree of protection IP 54 according to DIN EN
60529.
●The device shall be provided in a suitable fire enclosure in the end-use appli-
cation.
Risk to damage the device due to external influ-
ences
NOTICE
Keep the device away from oils and emulsions.
This is a product that corresponds to the limit values of the emitted
interference of class A (industrial environments). This is a product
that does not correspond to the limit values of the emitted interfer-
ence of class B (residential area and small enterprises)
When using the product in residential areas or small enterprises, the
operator has to take actions to prevent radio interferences (also re-
fer to DIN EN 55022).
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
11/41
Ambient conditions
R911376654_Edition 04 Bosch Rexroth AG

7 Technical data
7.1 Voltage supply
The Safety extension module IndraControl XFE01.1-SY-01 is supplied with 12 V
via a separate connection.
The input voltage of the Safety extension module is DC 24 V (as per the require-
ments acc. to DIN EN 61131-2). The voltage is supplied from PELV power supply
units with safe separation acc. to EN 50178 and EN 60950-1.
Nominal voltage DC 24 V +20%, -15%, PELV
Residual ripple ±5 %
ULmax 30 V
ULmin 19.2 V
Maximum current consumption of the module from
UL at nominal voltage
0.2 A
Tab. 7-1: Operating voltage and current consumption IndraControl XFE01.1-SY-01
The Safety extension module IndraControl
XFE01.1-SY-01 goes into a safe state in case of
undervoltage or overvoltage
NOTICE
Ensure that the voltages remain in the specified range.
7.2 Safety-related characteristic values
Safety integrity level SIL SIL3 (DIN EN 61508 and DIN EN 61131-6)
Performance level PL PL e (DIN EN ISO 13849-1)
Hardware error tolerance HFT = 1
Category Category 4 (DIN EN ISO 13849-1)
PFH (average frequency of a dangerous failure per
hour)
4.5 × 10-10 1/h
PFDavg (average probability of a dangerous failure
in case of request)
3.9 × 10-5
Service life TM20 years (DIN EN ISO 13849); no proof test
required
MTTFd (mean time to failure) 2,500 years
DCavg (average diagnostic coverage) 99 % ≙ high
Types of failure If the internal diagnostics of the Safety extension
module IndraControl XFE01.1-SY-01 detects an
error, the module goes into the safe state, that is,
no more safe bus telegrams are sent
12/41
Technical data
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04

7.3 Dimensions and weight
Dimensions (W × H × D) 35 × 122.4 × 95.8 mm
Weight (without packaging) 200 g
8 Standards
8.1 Standards used
The Safety function module IndraControl XFE01.1-SY-01 was developed accord-
ing to the following standards.
8.1.1 General standards
DIN EN IEC 61000-6-2:2019
IEC 61000-6-2:2016
Electromagnetic compatibility (EMC) –
Part 6-2: Generic standards – Immunity for industrial envi-
ronments
DIN IEC EN 61000-6-4:2020
IEC 61000-6-4:2018
Electromagnetic compatibility (EMC) –
Part 6-4: Generic standards – Emission standard for indus-
trial environments
DIN EN 60204-1:2019 (in excerpts)
EN 60204-1:2018 (in excerpts)
Safety of machinery –
Electrical equipment of machines –
Part 1: General requirements
DIN EN 61131-1:2004
IEC 61131-1:2003
Programmable controllers –
Part 1: General information
DIN EN 61131-2:2008 + Corr. 2009
EN 61131-2:2007
IEC 61131-2:2017
Programmable controllers –
Part 2: Equipment requirements and tests
DIN EN 61131-3:2014
IEC 61131-3:2013
Programmable controllers –
Part 3: Programming languages
Tab. 8-1: General standards
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
13/41
Standards
R911376654_Edition 04 Bosch Rexroth AG

8.1.2 Safety standards
DIN EN 61131-6:2013
EN 61131-6:2012
Programmable controllers –
Part 6: Functional safety
EN 61511-1:2017 + A1:2017 Functional safety –
Safety-instrumented systems for the process industry sector
–
Part 1: Framework, definitions, system, hardware and soft-
ware requirements
DIN EN 61508 Part 1-7:2011
EN 61508 Part 1-7:2010
IEC 61508 Part 1-7:2010
Functional safety of electrical/electronic/programmable elec-
tronic safety-related systems
DIN EN 62061:2016
EN 62061:2005 + Corr.:2010 +
A1:2013 + A2:2015
Safety of machinery –
Functional safety of safety-related electrical, electronic and
programmable electronic control systems
DIN EN ISO 13849-1:2016
EN ISO 13849-1:2015
Safety of machinery –
Safety-related parts of control systems –
Part 1: General principles for design
DIN EN ISO 13849-2:2013
EN ISO 13849-2:2012
Safety of machinery –
Safety-related parts of control systems –
Part 2: Validation
DIN EN 61326-3-1:2018
EN 61326-3-1:2017
Electrical equipment for measurement, control and laborato-
ry use –
EMC requirements –
Part 3-1: Immunity requirements for safety-related systems
and for equipment intended to perform safety-related func-
tions (functional safety) – General industrial applications
Tab. 8-2: Safety standards
14/41
Standards
IndraControl XFE01.1-SY-01 Safety Ex-
tension Module
Bosch Rexroth AG R911376654_Edition 04