Bosch VIP-X1XF User manual

VIP X1 XF
Network Video Server
en Quick Installation Guide

VIP X1 XF About this Quick Installation Guide | en 3
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.155.695 | V4.1 | 2009.12
1 About this Quick Installation Guide
This Quick Installation Guide applies to all variants of the
VIP X1 XF.
For further detailed information, please see the extensive
online Help for the VIP X1 XF.
This Quick Installation Guide, the Installation and Operating
Manual and the current firmware package are available in other
languages at www.boschsecurity.com.
WARNING!
You should always make yourself familiar with the required
safety measures in the relevant chapter of the Installation and
Operating Manual (see product CD). This contains important
information on installation and operation.
Only operate the VIP X1 XF in combination with an LPS/NEC
Class 2 power supply unit with limited output.
This Quick Installation Guide only describes the basic
procedure for installing a VIP X1 XF and cannot replace the
complete manual.

4en | Scope of Delivery VIP X1 XF
F.01U.155.695 | V4.1 | 2009.12 Quick Installation Guide Bosch Sicherheitssysteme GmbH
2 Scope of Delivery
– 1 VIP X1 XF network video server
– 2 terminal blocks
– 4 self-adhesive elastic bumpers
– 1 wall-mounting panel
–2screws
– 2 wall plugs
– 1 Quick Installation Guide
–1productCD

VIP X1 XF Unpacking | en 5
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.155.695 | V4.1 | 2009.12
3 Unpacking
– Check that the delivery is complete and in perfect
condition.
– Arrange for the unit to be checked by
Bosch Security Systems if you find any damage.

6en | Preparing for Wall-Mounting VIP X1 XF
F.01U.155.695 | V4.1 | 2009.12 Quick Installation Guide Bosch Sicherheitssysteme GmbH
4 Preparing for Wall-Mounting
You can secure the VIP X1 XF to any load-bearing wall using the
wall-mounting panel, in either a vertical or a horizontal position.
CAUTION!
If mounting the unit in a vertical position, you will need to use
the lower plastic frame and then place the unit onto the frame
from above. If mounting the unit in a horizontal position, you
can use either of the two frames.

VIP X1 XF Mounting the Frame | en 7
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.155.695 | V4.1 | 2009.12
5 Mounting the Frame
– Lift the plastic frame on one side of the housing and
carefully remove it from the unit.
– Screw the plastic frame in the required position together
with the wall-mounting panel.
– Check that the plastic frame is secure.
CAUTION!
The mounting location must be able to reliably hold the unit.
The load-bearing capacity must be adequate for four times the
weight of the unit.

8en | Placing the Unit in the Frame VIP X1 XF
F.01U.155.695 | V4.1 | 2009.12 Quick Installation Guide Bosch Sicherheitssysteme GmbH
6 Placing the Unit in the Frame
– Place the unit on the wall-mounting panel, with the panel
positioned between the housing and the second plastic
frame.
– Slide the unit into the plastic frame until you feel it lock
securely into place.
– Finally, check that the unit is securely attached in the
installation location.

VIP X1 XF Connecting the Camera and Audio | en 9
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.155.695 | V4.1 | 2009.12
7 Connecting the Camera and Audio
– Connect the camera to the socket VIDEO IN.
– Use the LINE IN/OUT socket for audio line connections.
CAUTION!
Please observe the following specifications:
Line In: 9 kOhm typ., 5.5 Vp-p max.
Line Out: 16 Ohm min., 3 Vp-p max.

10 en | Creating a Serial Connection VIP X1 XF
F.01U.155.695 | V4.1 | 2009.12 Quick Installation Guide Bosch Sicherheitssysteme GmbH
8 Creating a Serial Connection
– If you require a serial connection to the VIP X1 XF, connect
the relevant cables to the terminal block.
– Connect the terminal block to the orange socket on the
VIP X1 XF.
CAUTION!
Please observe the labeling on the orange socket of the
VIP X1 XF and the correct position for the terminal block.