Bosch VIP X1 User manual

VIP X1/VIP X2 – Network video server

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 2
These instructions "Quick Installation Guide" refer to the units VIP X1 and VIP X2, both in basic
and in audio version. The title shows the basic versions of VIP X1 and VIP X2. In the drawings the
VIP X1 in audio version is displayed standing for all versions.
Attention
You should always make yourself familiar with the required safety measures in the cor-
responding chapter of the user's manual. You will find more important details on the
installation and on the operation of the unit in the manual. These instructions "Quick
Installation Guide" only show the basic installation of a VIP X1 or VIP X2, but they are
no substitute for the complete user's manual.

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 3
Lieferumfang
• VIP X1 (oder VIP X2) Netzwerk Video Server,
Basisversion oder Audioversion
• Steckernetzteil mit vier Primäradaptern
• Konfigurationskabel
•CD-ROM
• Schnellstartanleitung
Contents of delivery
• VIP X1 (or VIP X2) Network Video Server,
basic version or audio version
• Power outlet with four primary adapters
• Configuration cable
•CD-ROM
• Quick Installation Guide

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 4
1.
• Please check the delivery for completeness and integrity.
• Have your unit checked by Bosch Security Systems if you detect any damages!

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 5
2.
• Connect the free leads of the configuration cable to the spring clamp connector that is already
connected to the power outlet.
• Connect the spring clamp connector to the orange socket of the unit.
• Connect the configuration cable with a serial interface of the computer.
• Make sure that the power outlet is provided with the correct primary adapter and plug the power
outlet into a suitable mains outlet.

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 6
3.
• Start the terminal program, enter service as user name.
•Enterthecommand1to open the IP menu.
•Enterthecommand1followed by the desired IP address (e.g. 192.168.0.30). The new IP
address is displayed and is valid after a reboot.
• Use the commands shown for further settings if required.

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 7
4.
• Disconnect the unit from the power mains and from the computer.
• Remove the leads of the configuration cable from the spring clamp connector.
•VIP X1: Connect the camera with the Video In socket.
VIP X2: Connect one camera to each, the Video In 1 socket and the Video In 2 socket.

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 8
5.
• Connect the alarm switches and the relay connections to the corresponding terminals.
• Connect the unit to the network via th ETH socket.
• Plug the power outlet into the mains outlet again.

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 9
6.
Units with audio only:
• Use the jack sockets for audio line connections.
• Connect the microphone and the speaker connection to the corresponding terminals.

Bosch Security Systems | 2005-10 | V1.5
VIP X1/VIP X2 | Quick Installation Guide EN | 10
7.
• Start your web browser and enter the IP address of the respective unit as URL (e.g.
http://192.168.0.30) to check that the unit is properly connected to the network.
•Note: The graphic adapter of your computer must be set to 16 bits or 32 bits color depth, other-
wise the video pictures cannot be displayed.
• Use the links on top of the pages to navigate through the pages.