Bosch DIP-5042EZ-0HD User manual

DIVAR IP 5000
DIP-5042EZ-0HD | DIP-5042EZ-1HD |
DIP-5042EZ-2HD | DIP-5042EZ-4HD |
DIP-5044EZ-1HD | DIP-5044EZ-2HD |
DIP-5044EZ-4HD
en Installation manual

DIVAR IP 5000 Table of contents | en 3
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
Table of contents
1Safety 4
1.1 Safety message explanation 4
1.2 Safety precautions 4
1.3 Important safety instructions 4
1.4 Notices 7
1.5 FCC and UL 8
2Available documentation 11
3System overview 12
3.1 Device views 12
3.2 LED description - front panel 15
3.3 LAN port LED description - rear panel 16
4Chassis setup 17
4.1 Removing hard drive trays 17
4.2 Installing a hard drive 18
5Installation - first steps 19
5.1 Setup notes 19
5.2 Connecting the unit 19
6Obtaining a basic configuration 20
7Advanced setup - dual network 21
8Advanced configuration 23
9Maintaining the system 25
9.1 Monitoring the system 25
9.2 Recovering the unit 26
9.3 Backing up the configuration 26
9.4 Adding/replacing hard disks 27
9.4.1 Extending a 2-disk unit 27
9.4.2 Extending an empty unit 28
9.4.3 Replacing hard disks 28
9.5 Updating the system 29
9.6 Using the IP Helper tool 30
10 End-user license agreement 31

4en | Safety DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
1 Safety
1.1 Safety message explanation
!
Warning!
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
!
Caution!
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
Notice!
Indicates a situation which, if not avoided, could result in
damage to the equipment or environment, or data loss.
1.2 Safety precautions
!
Caution!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code
(NEC800 CECSection60) or applicable local codes.
1.3 Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Follow all warnings before operating the
device.
– Clean only with a dry cloth. Do not use liquid cleaners or
aerosol cleaners.
– Do not install device near any heat sources such as
radiators, heaters, stoves, or other equipment (including
amplifiers) that produce heat.
– Never spill liquid of any kind on the device.
– Take precautions to protect the device from power and
lightning surges.

DIVAR IP 5000 Safety | en 5
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
– Operate the device only from the type of power source
indicated on the label.
– Install in accordance with the manufacturer's instructions in
accordance with applicable local codes.
– Use only attachments/accessories specified by the
manufacturer.
– Protect all connection cables from possible damage,
particularly at connection points.
– Do not defeat the safety purpose of a polarized or
ground‑type plug.
– Permanently connected devices must have an external,
readily operable mains plug or all‑pole mains switch in
accordance with installation rules.
– Pluggable devices must have an easily accessible socket-
outlet installed near the equipment.
– Unplug the unit from the outlet before cleaning. Follow any
instructions provided with the unit.
– Any openings in the unit enclosure are provided for
ventilation to prevent overheating and ensure reliable
operation. Do not block or cover these openings.
– Leave approximately 5cm (2inches) clearance to the next
object.
– Do not place the unit in an enclosure unless proper
ventilation is provided, or the manufacturer's instructions
have been adhered to.
– Do not use this unit near water, for example near a bathtub,
washbowl, sink, laundry basket, in a damp or wet
basement, near a swimming pool, in an outdoor installation,
or in any area classified as a wet location.
– To reduce the risk of fire or electrical shock, do not expose
this unit to rain or moisture.
– Never push objects of any kind into this unit through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electrical shock.

6en | Safety DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
– For added protection during a lightning storm, or when
leaving this unit unattended and unused for long periods,
unplug the unit from the wall outlet and disconnect the
cable system. This will prevent damage to the unit from
lightning and power line surges.
– Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, playing particular attention to cords and
plugs, convenience receptacles, and the point where they
exit from the appliance.
– Do not open or remove the cover to service this unit
yourself. Opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
Bosch Service Center.
– Observe the relevant electrical engineering regulations.
– Use proper CMOS/MOS-FET handling precautions to avoid
electrostatic discharge when adding or changing hard
disks.
– Install the unit only in a dry, weather-protected location.
– When installing in a switch cabinet, ensure that the unit and
the power supply units have sufficient grounding.
– Connect the unit to an earthed mains socket.
– For protection of the device, the branch circuit protection
must be secured with a maximum fuse rating of 16A. This
must be in accordance with NEC800 (CEC Section 60).
– All the input/output ports are Safety Extra Low Voltage
(SELV) circuits. SELV circuits should only be connected to
other SELV circuits.
– Disconnect the power before moving the unit. Move the
unit with care. Excessive force or shock may damage the
unit and the hard disk drives.
– If safe operation of the unit cannot be ensured, remove it
from service and secure it to prevent unauthorized
operation. In such cases, have the unit checked by Bosch
Security Systems.

DIVAR IP 5000 Safety | en 7
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
– Disconnect power supply and arrange for the device to be
serviced by qualified personnel in the following cases,
because safe operation is no longer possible:
– The power cable/plug is damaged.
– Liquids or foreign bodies have entered the device.
– The device has been exposed to water or extreme
environmental conditions.
– The device is faulty despite correct installation/
operation.
– The device has fallen from a height, or the housing has
been damaged.
– The device was stored over a long period under
adverse conditions.
– The device performance is noticeably changed.
1.4 Notices
Notice!
Video loss is inherent to digital video recording; therefore,
Bosch Security Systems cannot be held liable for any damage
that results from missing video information.
To minimize the risk of losing information, we recommend
multiple, redundant recording systems, and a procedure to
back up all analog and digital information.

8en | Safety DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
Disposal
Your Bosch product has been developed and
manufactured using high-quality materials and
components that can be reused.
This symbol means that electronic and electrical
devices that have reached the end of their working
life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already
in place for used electrical and electronic
products. Please dispose of these devices at your
local communal waste collection point or at a
recycling center.
Notice!
Do not dispose batteries in household waste. Dispose of
batteries only at suitable collection points and, in the case of
lithium batteries, mask the poles.
Do not place this unit on an unstable stand, tripod,
bracket, or mount. The unit may fall, causing
serious injury and/or serious damage to the unit.
1.5 FCC and UL
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules and ICES-003 of Industry Canada. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no

DIVAR IP 5000 Safety | en 9
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna;
– Increase the separation between the equipment and the
receiver;
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
– Consult the dealer or an experienced radio/TV technician
for help.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the
dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office, Washington,
DC 20402, Stock No. 004-000-00345-4.
UL Disclaimer
Underwriter Laboratories Inc. ("UL") has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in Standard(s) for Safety for Information
Technology Equipment, UL 60950-1 . UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.

10 en | Safety DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.

DIVAR IP 5000 Available documentation | en 11
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
2 Available documentation
This manual is available in different languages. You can find all
manuals in the online product catalog.
Documentation and software for Bosch Security Systems
products can be found in the online product catalogue as
follows:
4Open any browser > enter www.boschsecurity.com > select
your region and your country > start a search for your
product > select the product in the search results to show
the existing files.

12 en | System overview DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
3 System overview
The DIVAR IP 5000 system is an affordable, easy to use all-in-one
recording solution for network surveillance systems of up to
32channels. All channels are pre-licensed. Running the full
Bosch recording solution, DIVAR IP 5000 is an intelligent IP
storage device that provides both, a professional video
recording solution and ease of operation.
DIVAR IP 5000 is a 4-bay mini tower unit that combines
advanced management and state-of-the-art recording
management into a single, cost-effective, plug and play IP
recording appliance for IT-minded customers.
DIVAR IP 5000 utilizes a highly energy efficient, embedded
design at a very affordable price which nevertheless boasts
Bosch quality through-and-through.
Easy to install and operate, DIVAR IP 5000 features wizard-
based set-up and centralized configuration to reduce installation
times. All components are pre-installed and pre-configured.
Simply connect to the network and turn on the unit — DIVAR IP
5000 is ready to begin recording straight out-of-the-box.
DIVAR IP 5000 features front-swappable SATA-II hard drives. All
system software is pre-installed and pre-activated — creating a
ready-to-use video recording appliance.
3.1 Device views
There are several LEDs on the front and rear of the chassis. The
LEDs show the over-all status of the system and the activity and
health of specific components.

DIVAR IP 5000 System overview | en 13
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
Front view:
1
52 3 4
6
1Lock for front cover 4LAN activity LED
2Power on/off LED 5System status LED
3Hard disk access LED 6Individual hard disk LED

14 en | System overview DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
DIVARIP rear view:
3 4
1 2 75 6
1Factory reset button 52x Alarm Out
21x Display port
Note: Only for
troubleshooting.
62x Alarm In
32x Ethernet (RJ45) 7Mains connection 100 -
240 VAC

DIVAR IP 5000 System overview | en 15
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
44x USB 3.0
Note: Only for
troubleshooting.
3.2 LED description - front panel
This chapter describes the LED displays on the front of the
chassis.
LED
indicator
LED
color
LED
state
Description
Power
LED
N/A Off Power off
Blue On
(default)
Working
HDD LED N/A Off No disk access
Blue Blinking Disk access
LAN LED N/A Off Network disconnected
Blue On Network connected
Blue Blinking Network activity
System
LED
N/A Off System has booted in normal
operation.
Blue Blinking System is booting or a
software update is being
applied.
Red On Undefined software error.
Contact technical support.

16 en | System overview DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
LED
indicator
LED
color
LED
state
Description
Individual
hard disk
LED
N/A Off
(default)
No hard drive configured for
this bay.
Blue On Hard drive present and
working.
Blue Blinking Hard drive health not optimal
— needs attention.
Red On Hard drive is configured for
this bay, but is not working.
3.3 LAN port LED description - rear panel
This chapter describes the LAN port LED on the rear of the
chassis.
LAN connector:
12
Nr. LED
indicator
LED
color
LED
state
NIC state
1RJ45 LED
(left)
N/A Off No connection or
10Mb/s
Green On 100 Mb/s
Yellow On 1000 Mb/s
2RJ45 LED
(right)
Yellow On Active connection
Yellow Blinking Transmit or receive
activity

DIVAR IP 5000 Chassis setup | en 17
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
4 Chassis setup
This chapter covers the steps required to install components
and perform maintenance on the chassis.
!
Caution!
Review the warnings and precautions listed in the manual
before setting up or servicing this chassis.
Observe the following prerequisites when adding or replacing
hard disks.
Prerequisites:
– For RAID configuration, all hard disks of the unit must have
the same capacity
Notice!
Insert the hard disks before initial system start.
See also
– Safety, page 4
– Installing a hard drive, page 18
4.1 Removing hard drive trays
The drives are mounted in drive carriers to simplify their
installation and removal from the chassis. These carriers also
help promote proper airflow for the drive bays.
To remove hard drive trays from the chassis:
1. Turn off the system.
2. Press the release button on the drive carrier. This extends
the drive carrier handle.
3. Use the handle to pull the drive carrier with the drive out of
the chassis.

18 en | Chassis setup DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
4. Insert the drive carrier with the new drive into the chassis
bay, making sure that the drive carrier handle is completely
closed.
4.2 Installing a hard drive
The drives are mounted in drive carriers.
To install a hard drive to the hard drive carrier:
1. Remove the drive from the carrier.
2. Install a new drive into the carrier with the printed circuit
board side facing down so that the mounting holes align
with those in the carrier.
3. Replace the drive carrier into the chassis bay, making sure
that the drive carrier handle is completely closed.
Notice!
We recommend using the respective Bosch hard disk drives.
The hard disk drives as one of the critical component are
carefully selected by Bosch based on available failure rates.
HDD – not delivered from Bosch – are not supported.
Information on supported HDDs can be found in the datasheet
in the Bosch Online Product Catalog.
See also
– Available documentation, page 11

DIVAR IP 5000 Installation - first steps | en 19
Bosch Sicherheitssysteme GmbH 2016.03 | V1 | DOC
5 Installation - first steps
DIVARIP systems are shipped with a pre-installed browser-
based configuration wizard.
5.1 Setup notes
By default all DIVARIP systems are configured to obtain a valid
network address from DHCP server in the local network. In
small networks this task is usually performed by an internet
router. If there is no DHCP server in the network, DIVARIP will
use the following network settings:
– IP Address: 192.168.0.200
– Subnet mask: 255.255.255.0
Notice!
We strongly recommend that you do not change any operating
system settings. Operating system access should only be used
for troubleshooting. Changes can result in malfunctioning of the
system.
5.2 Connecting the unit
DIVARIP system is ready to go out of the box. The application
provides a simple to install and intuitive to use solution for
network surveillance systems.
Connecting the unit:
1. Connect the unit and the cameras to the network.
2. Connect the unit to the power supply.
3. Turn on the unit.
Note: During this initial setup the system LED is blinking.
After the system is ready for operation, the system LED
stops blinking. The web based wizard pages of the DIVAR IP
can be accessed from any browser within the network. Use
these web page wizard pages to obtain a basic system
configuration.

20 en | Obtaining a basic configuration DIVAR IP 5000
2016.03 | V1 | DOC Bosch Sicherheitssysteme GmbH
6 Obtaining a basic configuration
DIVAR IP 5000 offers an easy-to-use configuration wizard to
achieve a basic configuration of a smaller system easily.
To achieve a basic configuration using the Configuration Wizard:
1. Open a web browser from any PC in the network, enter the
IP address of DIVARIP in the address bar, then press
ENTER. The Welcome page of the Configuration Wizard is
displayed.
Note:
If you do not know the IP address, proceed as follows:
– Only one DIVAR IP 5000 is in the network:
Enter http://mydivar or https://mydivar, then
press ENTER. The Welcome page of the Configuration
Wizard is displayed.
!! Use mydivar only if there is one DIVARIP in the
same network, not if there are multiple DIVARIP.!!
– Multiple DIVAR IP 5000 are in the same network:
Use the IP Helper tool to display all devices with their
IP addresses. The tool is available in the online catalog
on the DIVAR IP 5000 product page.
2. On the Welcome page select your preferred language, then
click Start configuration.
3. Run-through the wizard and follow the instructions. Each
page provides you with information how to use it.
4. After finishing the Configuration Wizard your system has a
basic configuration available. If the basic configuration
needs to be extended, use the advanced configuration.
See also:
– Using the IP Helper tool
– Advanced configuration