Bosch Solution 16i User manual

Solution 16i
Security System
User Guide
EN
Security Systems

Solution 16i
2Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Copyright Notice
Unless otherwise indicated, this publication is the
copyright of Bosch Security Systems Pty Ltd (“Bosch”). All
rights are reserved.You may download a single copy of this
publication. By downloading the publication you agree that
you will: (i) only use the publication for your own reference;
(ii) not commercially exploit or charge any person for the
use of the publication; and (iii) not modify the publication
in any way without the prior written permission of Bosch.
Except as specied above or where authorised by the
Copyright Act 1968 (Cth), no part of this publication may
be reproduced, transmitted, modied or stored in any form
or by any means, without the prior written permission of
Bosch.
Trademarks
Throughout this document trademark names may have
been used. Rather than put a trademark symbol in every
occurrence of a trademark name, we state that we are using
the names only in an editorial fashion and to the benet of
the trademark owner with no intention of infringement of
the trademark.
Notice of Liability
While every eort has been taken the accuracy of this
document, neither Bosch Security Systems Pty Ltd nor any
of its ocial representatives shall have any liability to any
person or entity with respect to any liability, loss or damage
caused or alleged to be caused directly or indirectly by the
information contained in this book. Should you nd any
error on inconsistency, please notify us accordingly.
Bosch Security Systems Pty Ltd reserves the right to make
changes to features and specications at any time without
prior notication in the interest of ongoing product
development and improvement.
New Zealand Telepermit Note
The grant of a Telepermit for a device in no way indicates
Telecom acceptance of responsibility for the correct
operation of that device under all operating conditions.
This equipment shall not be used in any manner that could
constitute a nuisance to other Telecom customers.
Immediately disconnect this equipment should it become
physically damaged, and arrange for its disposal or repair.
The transmit level from this device is set as a xed level
and because of this there may be circumstances where the
performance is less than optimal. Before reporting such
occurrences as faults, please check the line with a standard
telepermitted telephone.
Warnings
1. This product must be installed by a qualied and
licensed security installer.
2. This product may not perform as expected if installed
incorrectly.
3. Some features of this product require a working
telephone line to operate and telephone
communication service provider charges may be
applicable.
4. Australian standard AS 2201 require regular service
by qualied and licensed security persons and
regular user testing. Please consult your security
alarm company for further details.
5. Incorrect programming of options can result in
operation contrary to what may be desired.
6. Leave the mains adapter plugged in at all times.
7. Leave the telephone line plugged in at all times
under normal conditions.
Notice to Owner
Thankyou for selecting the Solution 16i Security Control Panel for your security needs. Your system includes many
advanced features and functions which will be programmed and congured by your security consultant during installation.
Depending on the conguration, and your access level, you may have the ability to program certain features within the
system to suit changes in your security needs. For example you may wish to change a User Name or PIN number when a
sta member leaves.
This manual explains all aspects of system operation as well as detailling the various programming options available to
you. We ask that you take the time to read this manual carefully and that you have your installer explain the basic system
operation and conguration to you when the installation is complete.

3
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Copyright Notice ................................................................... 2
Trademarks ............................................................................. 2
Notice of Liability .................................................................. 2
Notice to Owner..................................................................... 2
New Zealand Telepermit Note ............................................ 2
Contents ................................................................................3
Programming Menu .............................................................4
Introduction..........................................................................5
Features.................................................................................5
User’s Guide ..........................................................................5
Reporting Alarms .................................................................6
About the Keypad.................................................................6
Keypad Keys ........................................................................... 6
Status Icons / LED’s................................................................ 7
Keypad Tones ......................................................................... 7
Basic System Operation .......................................................8
Turning An Area All On......................................................... 8
Turning An Area Part On / Part 2 On .................................. 8
Turning The System O ........................................................ 9
Silencing Alarms .................................................................... 9
Automatic Arming................................................................. 9
Duress or Silent Alarms ........................................................ 9
Remote Arming - Quick Arm ............................................... 9
DTMF Control Functions ...................................................... 9
Programming Text Using The Keypad ............................. 10
System Programming........................................................ 11
Erase User .......................................................................... 11
Change Own PIN .............................................................. 11
Change Other PIN ............................................................ 11
Add PIN .............................................................................. 11
Delete PIN.......................................................................... 12
Proximity Tokens & Cards................................................... 12
Add Token.......................................................................... 12
Delete Token ..................................................................... 13
Token Status...................................................................... 13
RF Radio Keyfobs................................................................. 13
Add Keyfob........................................................................ 13
Delete Keyfob ................................................................... 13
User Name ......................................................................... 14
Area Assignment.............................................................. 14
Timer Groups ....................................................................... 14
Timer Group...................................................................... 15
Access Group .................................................................... 15
Areas ...................................................................................... 15
Area Status ........................................................................ 15
Turn Area On..................................................................... 16
Turn All Areas On ............................................................. 16
Turn All Areas O ............................................................. 16
Move To Area .................................................................... 16
Chime On/O.................................................................... 17
Chime Mode...................................................................... 17
Area Name......................................................................... 18
Input Options ....................................................................... 18
Zone Status ....................................................................... 18
Bypass Zones .................................................................... 19
Set Chime Zones .............................................................. 19
Set Part 2 Zones ............................................................... 19
Smoke Sensor Reset ........................................................ 20
Zone Name........................................................................ 20
Walk Test All Zones .......................................................... 20
Walk Test A Single Zone.................................................. 21
Output Options.................................................................... 21
Output Status ................................................................... 21
Turn Output On/O ......................................................... 22
Output Name .................................................................... 22
External Siren Test ........................................................... 22
Internal Siren Test ............................................................ 23
Strobe Test......................................................................... 23
Communication / Reporting.............................................. 23
Call/Answer RAS............................................................... 23
Call Forward On/O......................................................... 23
Direct Link Connect ......................................................... 24
Voice Setup ....................................................................... 24
Set Domestic Phone Number ........................................ 24
Call Forward On................................................................ 24
Call Forward O ............................................................... 25
Email Address ................................................................... 26
Email Options ................................................................... 26
Send Test Report .............................................................. 26
Devices and Optional Modules......................................... 27
LAN Status......................................................................... 27
Volume............................................................................... 27
Contrast ............................................................................. 27
Backlight............................................................................ 27
System Options and Events............................................... 28
Panel Status ...................................................................... 28
System Trouble................................................................. 28
Set Date & Time ................................................................ 28
Summer Time On ............................................................. 29
Summer Time O ............................................................. 29
Schedules.............................................................................. 30
Name .................................................................................. 30
Time.................................................................................... 30
Day...................................................................................... 31
Name .................................................................................. 31
Start / Stop Day ................................................................32
Keypad Hi/Lo Temp.......................................................... 32
Walk Test All Zones .......................................................... 33
Battery Test ....................................................................... 33
System Trouble Event Listing ........................................... 34
How System Troubles Are Displayed ............................... 34
Installation Details ............................................................ 37
Index................................................................................... 38
Contents

Solution 16i
4Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Programming Menu
The Solution 16i control panel includes an extensive range of features and options which enable your installer to taylor
the system to suit your exact security requirements. The panel includes a number of user options which can be changed
or modied by you if and when required.
This guide explains each of these in detail and includes examples on how to use each particular feature. The examples
show how to perform each function using the menu or loaction numbers in the system. It is also possible to access many
of the options using the simple text menus shown in the table below.
To access the text menus, enter your PIN + [MENU] key. Once the Access menu appears, use the [↑], [], [←]and [→]
naviagation keys to move around the menus and options. To drill down into an option press the [OK] key and follow the
prompts. To move back one level, press the [MENU] key. When programming locations, pressing the [OK] key will save
your changes and pressing the [MENU] key will abort any changes you have made in that location. To exit programming
at any time press and hold the [MENU] key for 2 seconds.
If you are unclear on any items in this guide, please contact your installer as they are best equiped to answer questions
releating to your particular installation.
Menu Nº Display Access Menu Menu Nº Display Comms Menu
1-1-0 ch-Pin Change Own PIN 5-1-5 set-ph Domestic Phone Nº
1-1-1 ch-Oth Change Other PIN 5-0-2 cfOnOf Call Forward On/O
1-4-1 UrAreA Area Assignment 5-1-6 cfOnPh Call Forward On Ph Nº
1-1-2 AddPin Add PIN 5-1-7 cfOfph Call Forward O Ph Nº
1-2-0 AddPrO Add Token 5-0-1 cAlAns Call / Answer RAS
1-3-0 AddFOb Add Keyfob 5-0-5 dircOn Direct Connect
1-1-3 delpin Delete PIN 5-0-8 cusreg Customer Registration
1-2-1 delprO Delete Token 5-9-0 tst-dl Send Test Report
1-3-1 delfOb Delete Keyfob 5-3-8 ur-rAs User RAS Security PIN
1-0-0 del-ur Erase User 5-0-6 VOice Voice Module Setup
1-4-4 tmrGrp Timer Group 5-5-8 EmAil Email Address
1-4-5 ur-Acc Access Assignment 5-5-9 E-Opts Email Options
1-2-2 id PrO Token Status
1-4-0 UrnAme User Name Devices Menu
6-1-0 cp-vOl Volume
Areas Menu 6-1-1 cp-cOn Contrast
2-0-5 chOnOf Chime On/O 6-1-2 cp-bl Backlight
2-0-6 ch typ Chime Mode 7-7-3 cP-deg Hi/Lo Temperature
2-1-0 A-NAme Area Name 6-0-0 LAN-St LAN Status
Inputs Menu System Menu
3-0-0 stAtus Zone Status 7-0-0 StAtus Panel Status
3-0-2 bypAss Bypass Zones 7-1-0 cLOck Set Date & Time
3-0-5 Fire-r Smoke Sensor Reset 7-1-1 St-On Summer Time On
3-0-3 ch-Zn Set Chime Zones 7-1-2 St-Off Summer Time O
3-0-4 pt2-zn Set Part 2 Zones 7-0-2 HislOg View History Log
3-9-1 tst-zn Walk Test A Zone 5-0-4 SndLOg Email History Log
3-9-0 tstzns Walk Test All Zones 7-0-1 trbl System Trouble
3-1-0 znnAme Zone Name 7-9-1 tst-bA Battery Test
7-5-1 Shtime Schedule Time
Outputs Menu 7-5-2 Sh DAy Schedule Day
4-0-0 stAtus Output Status 7-5-0 ShNAme Schedule Name
4-0-1 On-Off Turn Output On/O 7-6-0 HonAme Holiday Name
4-9-0 tstsir External Siren Test 7-6-1 Hotime Holiday Dates
4-9-1 tstInt Internal Siren Test 7-7-7 Site Site Name
4-9-2 tststr Strobe Test AboVt Panel Information
4-1-0 OPnAme Output Name
Table 1: Programming Menu Structure

5
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Introduction
Your system helps to secure life, property and investments
against re, theft and bodily harm. It consists of a keypad
(or keypads), sensors such as motion detectors or devices
located on doors and windows, and other sensing devices
designed to detect the presence of smoke or combustion.
The location and quantity of sensing devices will have
already been discussed with you by your alarm installer.
Control of your security system is achieved through the
unique ICON keypad, which displays all system information
using Icon Symbols with text prompts for most common
functions. Its versatility and ease of operation, make it
ideal for any home or business application.
Features
Listed below are the main features of the Solution 16i
control panel.
Up to 16 Fully Programmable Zones
Fire Alarm Verification
Up to 48 Unique PIN Numbers (Users)
Up to 4 Relay Outputs via optional output expander
4 Open Collector Outputs
Supervised Siren Driver
8 Programmable Schedules
Up To 4 Areas including a common area
Built-In Dialler
Up To 8 Fully Supervised ICON Keypads
Optional Voice Module
256 History Event Memory
Optional Clock Back-up Module
Programmable Via Keypad
Remote Programmable Via Upload/Download Software
Alarm Event Memory
Optional Ethernet Module
Built-In Telephone Line Fail Monitor
Us er ’s G ui de
This user’s guide shows you how to use and maintain
your security system. It covers basic functions, such as
turning the system on and o as well as some general
programming. More complex programming and system
conguration should be performed by your installer.
Many of the programming functions described in this
guide will have already been programmed by your alarm
installer while others may need to be programmed or
changed by you. Depending on your particular system
conguration some features described in this manual
may not be available. Please discuss this with your alarm
installer.
Functions outlined in this user guide may require you to
enter your PIN (Personal Identication Number) so make
sure you choose a number that is easy to remember. For
security reasons do not write this code down or give it to
anyone else. If more than one person needs to operate the
system then you should create a unique code for them if
this has not been done by your installer. This guide will
explain how to do this.
Please take the time to familiarise your self with the
following terms before reading the rest of this guide.
Zones
A‘Zone’is a detection device, or group of devices connected
to your security system. Zones are identied by the area
they monitor, such as a front door, bedroom window or
hallway.
Faulted Zones
When a zone (such as a door or window) is closed, it is
said to be ‘normal’. When the door or window is open, the
zone is said to be ‘faulted’. When you turn your system
on, you will usually want all of the zones in your system
to be normal, although, you can turn your system on with
faulted zones.
Zones Types
There are two basic types of zones, Non 24-hour and 24-
hour. See below.
Non 24-Hour Zones
Non 24-hour zones respond to alarm conditions
depending upon whether the system is turned on or o.
They are programmed to either respond instantly to alarm
conditions or to provide a delay for you to reach the keypad
and turn the system o. Various zones will be located
throughout your premises.
When you turn your system on, you have the option of
turning on all zones (All On), or just some of the zones (Part
On). Refer to“Turning An Area All On”and“Turning An Area
Part On / Part 2 On”on page 8 for more information.
Bypassed Zones
A zone which has been bypassed will remain unarmed
when the system is armed. You may need to bypass a
zone when doing renovations in the building or if a sensor
becomes faulty. Bypassed zones will reset the next time
the system is disarmed.
24-Hour Zones
24-hour zones are always on and cannot be turned o,
even when the system is turned o (disarmed). There are
two types of 24-hour zones, re zones and non-re zones.
What Is An Area?
The Solution 16i control panel comes defaulted and
programmed for a single area conguration (Area 1),
therefore, all zones are assigned to Area 1. The alarm
system can be divided into 4 individual areas running
o the same control panel. In this case, your installation
company would assign dierent sensors (zones) to each
area according to the section of the bulding they are in.
Example:
Partitioning a commercial business to 4 individual areas
may be as follows:
Area 1 – Main entry/exit area
Area 2 – Sales
Area 3 – Administration
Area 4 – Dispatch
Each area can be controlled individually as if they were
separate alarm systems.

Solution 16i
6Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
All On
When you turn an area All On, you are turning on all non 24-
hour zones, both interior (motion detectors) and perimeter
(doors and windows of the building).
Part On
When you turn an area Part On, you only turn on some of the
non 24-hour zones. Your security company will program
which zones are included in this portion. Part zones may
include only the perimeter (doors and windows) of your
alarms system, or sensors in other areas of your premises.
Check with your installation company to learn which zones
are Part zones.
Reporting Alarms
Your system may be programmed to send reports to
a alarm monitoring centre. These centres are maned
24hrs a day and can take action on your behalf when
an alarm occurs. Once the alarm report is complete,
the system returns the telephone to normal operation.
Your security company will advise you how your system
has been congured for alarm reporting.
Your system will make repeated attempts to send reports
to the monitoring centre. If your system fails to report, the
keypad will display the ‘service’ symbol.
Ab out the Ke ypa d
Your keypad has 20 keys. The keys allow you to input
instructions and perform programming as required. Some
keys have a secondary function which is activated by press
and holding them down for two seconds.
Each keys’ function is described below:
Keypad Keys
Key Description
to
The numeric keys allow you to enter
you numbers when required.
Use the [MENU] and the numeric keys
to enter commands. The [MENU] key
is also used to go back one level when
navigating through menus or to exit a
programming location without saving
changes.
The [ON] key allows you to turn an area
or output on. To turn all areas on at the
same time when the system has been
partitioned, press and hold the [ON]
key for two seconds.
The [PART] key allows you to turn an
area Part On. This key can also be used
to bypass a zone or multiple zones
when you press and hold for two
seconds.
Key Description
The [OFF] key allows you to turn an
area or output o. To turn all areas o
at the same time when the system has
been partitioned, enter PIN and press
and hold the [OFF] key for two seconds.
The [OK] key allows you to select
options and conrm programming
changes.
The [MAIL] key is used to initiate a
dialer test when you press and hold for
two seconds.
The [] key allows you to move the
cursor left when programming text or
telephone numbers.
The [] key allows you to move the
cursor right when programming text
or telephone numbers.
The [↑] key allows you to navigate
through menus or to toggle characters
when programming text or telephone
numbers.
The [] key allows you to navigate
through menus or to toggle characters
when programming text or telephone
numbers. Pressing The [] key will
display current trouble conditions
when the area that the keypad is
displaying is disarmed.
+
for 2 sec
Pressing the [] and [↑] keys together
and holding them down for 2 seconds
will cause trigger a Panic alarm. If
programmed the sirens will sound and
the monitoring station will be notied.
+
for 2 sec
Pressing the [] and [] keys
together and holding them down for
2 seconds will trigger a Fire alarm. If
programmed the sirens will sound and
the monitoring station will be notied.
+
for 2 sec
Pressing the [↑] and [] keys together
and holding them down for 2 seconds
will trigger a Medical alarm. If
programmed, the sirens will sound and
the monitoring station will be notied.
Table 2: Keypad Keys and Their Function
KEYPAD EMERGENCY ALARM TRIGGER’S
Key Sequence Event Triggered
Ë+ ÊHold for 2 seconds Keypad Fire Alarm
Ê+ ÈHold for 2 seconds Keypad Panic Alarm
È+ ÂHold for 2 seconds Keypad Medical Alarm
Table 3: Keypad Emergency Alarm Trigger’s

7
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Figure 1: Keypad Emergency Alarm Trigger’s
Status Icons / LED’s
The following table lists the function of each of the ICON
Symbols and LED Indicators on the ICON Keypad Display.
Figure 2: LCD Display Showing All ICONs
Icon Status Meaning
AREA
The keypad can display which areas (1 – 4) are
turned on or o via the Area Icon Indicators.
On The area is All On or Part On.
O The area is O.
Flashing
Fast The area has an alarm.
POWER
On System power is normal.
Flashing System power is missing.
FIRE
Flashing A re alarm is active.
O No re alarm.
On Fire alarm in memory (Turn the
area All On and O to clear).
!
SERVICE
On The existing service or trouble
condition has been acknowledged.
O No service or trouble conditions
exist.
Flashing
A service or trouble condition is
present that has not been acknowl-
edged.
M
PART
On Area is Part On or Part 2 On.
O The area is not Part On.
Icon Status Meaning
OFF
On The area is O.
O The area is All On or Part On.
ON
On The area is All On.
O The area is O.
(
()
)
CHIME
On Chime mode is ON.
O Chime mode is O.
PHONE
On Phone Line in use.
O Phone Line not in use.
Red
LED
On The Area or System is Armed.
Flashing Alarm.
Green
LED
On Areas or System Disarmed.
Flashing Area not ready to turn on.
9 10
11 12
13 14
15 16
1 2
3 4
5 6
7
8
On Zone Open. (Unsealed or Faulted).
O Zone Closed. (Sealed or Normal).
Flashing Zone in Alarm or Alarm Memory.
Table 4: Status ICONs, LED Indicator’s and Their Meanings
Keypad Tones
Your keypad emits several distinct tones to alert you about
various system events. Additional bells or sirens may also be
connected to your system. Bells or sirens mounted on the
exterior of your premises alert neighbours to emergencies
and provide an audible guide for police and re ghters.
Type Meaning
Fire
Alarm
Tone
When a re zone sounds an alarm, the
keypad will sound 3 seconds on and 2
seconds o (repeat).
Burglary
Alarm
Tone
When a burglary zone activates while your
system is turned on, your keypad emits a
continuous siren tone. It sounds for the
time set by your security company.
Trouble
Tone
When a system component is not
functioning properly, your keypad sounds
4 fast short beeps followed by a 5 second
pause (repeat).

Solution 16i
8Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Key
Press
Tone
Pressing any key on the keypad sounds one
short beep, indicating that the key press is
accepted.
Entry
Delay
Tone
When you enter the premises through
a zone programmed for entry delay, the
keypad sounds a Hi/Low (repeat) tone to
remind you to turn o the area. If the area
is not turned o before the entry delay
expires, an alarm condition will sound and
a report (if programmed) will be sent to
your alarm company.
Exit
Delay
Tone
After you turn an area All On, the keypad
will sound 1 short beep every second.
During the last 10 seconds fast short beeps
will be heard. If you don’t exit before the
delay time expires and an exit delay door is
faulted, an alarm occurs.
Error
Tone
If you press an incorrect key, your keypad
will sound a 2 second tone.
Menu
Mode
The keypad will sound a tone to indicate
when you enter or leave the MENU
Programming Mode.
Chime
Tone
The keypad sounds fast short beeps to alert
you when a zone programmed for chime is
faulted or unsealled.
Table 5: Keypad Tones and Their Meanings
Figure 3: CP510i ICON Keypad
Bas ic System Operati on
Turning An Area All On
Use this function to turn the system All On. As soon as you
turn an area on, exit delay time will start. Exit time allows
you to exit the premises without sounding an alarm. Your
installer will program the length of exit delay time to suit
your premises.
1. Make sure that all zones are normal (not faulted).
The green indicator light will be on steady
2. Enter your PIN, then press the [ON] key.
If your PIN is valid and if all zones are normal, exit delay
time will start. You should leave now. If the control
panel detects a faulted zone, you should return it to
the normal condition, or manually bypass the zone.
During exit delay, you may stop the area from turning
All On by entering your PIN followed by the [OFF] key.
3. To turn the system (or area) o, enter your PIN, then
press [OFF].
i
Note
The system is factory defaulted for one area. If your
installation has been congured for multiple areas it
will be possible to turn on certain areas while leaving
others turned o.
Turning An Area Part On / Part 2 On
Use this function to turn an area Part On or Part 2 On. Part
On and Part 2 On modes can be used to turn on only part of
the area, leaving the rest of the area turned o.
Only your installer can program which zones are monitored
for Part On. However, a master user (default = User 1)
can program which zones are monitored when an area is
turned Part 2 On.
Once you have turned an area Part On or Part 2 On, exit
time will start. You should leave all zones that are active
before exit delay time expires. Leaving active zones after
exit delay expires causes an alarm event.
Use Part On or Part 2 On only when you want part of an
area turned on.
1. Make sure that all zones are normal (not faulted).
2. Enter your PIN, then press the [PART] key once.
If the area has zones programmed for Part 2, the keypad
will prompt the user to cursor between Part 1 and Part
2 options using the [] and [] keys before pressing the
[OK] key.
If your PIN is valid and all zones are normal, the area
will turn Part On and the exit delay time will start.
If your system has a faulted zone, you should return
it to the normal, or manually bypass the zone before
continuing.
During exit delay, you may stop the area from turning
Part On by entering your PIN followed by the [OFF] key.

9
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Turning The System O
When the system is on, you must enter through a
designated entry door to prevent an alarm. Opening the
door (e.g. front door) will start the entry timer. During
entry time, the keypad will emit a pulsing “beep”to remind
you to turn the area o.
If you enter through the wrong door or fail to turn the
area o before the entry delay time expires, the system
may sound an alarm. If an alarm occurs, silence the alarm
(by entering your PIN followed by the [OFF] key) and call
your security company to let them know that it is not an
emergency situation.
1. Enter your PIN + [OFF] to turn the system (or area) o.
The keypad will display the‘O’ icon.
Silencing Alarms
When the system has registered an alarm, the keypad (s)
and sirens will sound to alert personnel that an alarm has
occurred. The zone or zones which triggered the alarm will
be ashing on the keypad display for visual feedback. If you
silence and turn o an area before the siren time expires, a
‘cancel’report may be sent to your security company.
1. Enter your PIN + [OFF] to silence any alarm and turn
the area o.
The keypad will continue to ash the zone indicator of
the zone which caused the alarm. This is called alarm
memory.
2. To clear alarm memory, turn the area on and o
again. (eg. PIN + [ON] + PIN + [OFF].
Automatic Arming
One or more areas can be programmed by your installer
to automatically turn All On or Part On for one or multiple
days of the week.
If for some reason you are still in the building when the
auto arming is taking place, it is possible to extend or delay
the auto-on time (automatic arming time) by one hour if
required. During the auto-on pre-alert time, the keypad
buzzer sounds and displays the word AUTO on the screen.
To delay, enter your PIN + [OFF] key. The system will
prompt with the word Delay? Press [OK] to conrm that
you want to delay the arming sequence.
Example:
If the control panel is programmed by your installer to
automatically turn All On at 6:00pm and the auto-on pre-
alert time starts beeping the keypad at 5:55pm, enter your
PIN+[OK] and then when prompted press [OK] to delay.
The auto-on pre-alert time will commence again 1 hour
later at 6:55pm. If no further delays are requested system
will automatically turn All On at 7:00pm.
Duress or Silent Alarms
A Duress or Silent Panic alarm can be easily initiated via
the keypad if you are being forced to operate the system
against your will. No sirens will operate or sound during
a Duress or Silent Alarm activation. This will allow the
system to send a‘duress’report to your monitoring security
company without sounding any audible alarm.
To initiate a duress, enter your PIN followed by the last 2
digits of your user PIN followed by the [ON] or [OFF] key.
See the following examples.
1) If your PIN is 2580, to send a duress report when the area
is turned o, Enter, [2] [5] [8] [0] + [8] [0] + [OK] or [ON].
2) If your PIN is 2580, to send a duress report when the area
is All On or Part On, Enter, [2] [5] [8] [0] + [8] [0] + [OFF].
Remote Arming - Quick Arm
If you forget to turn on your system, it is possible for
you (at factory default) to remotely turn on your system
using a touch tone telephone. This option can only be
programmed by your installer.
To arm the system call the number which the panel is
connected to and when the panel answers you will here
3 beeps in accending frequency if the panel is in the
disarmed condition. Press [0] + [#] to arm. You will hear 3
beeps in decending order when the panel arms.
All areas on the system will be armed regardless of there
condition when using the DTMF quick arm function.
DTMF Control Functions
Your system’s telephone line interface provides for
comprehensive DTMF control of individual areas and
outputs with full user PIN and TIMER GROUP access
verication.
Your installer will advise you which DTMF features have
been enabled on your system.
How to Use DTMF Control
1. Call the telephone number that the control panel is
connected to.
When the control panel answers the incoming call, you will
hear a short welcome jingle. You now have approximately
5 seconds to enter a valid PIN and log onto the panel.
2. Enter your PIN + [#].
If the PIN is valid, the system will respond with two short
beeps. If the PIN is invalid then a single long beep will be
heard.
If a valid PIN is not entered in time, the panel will attempt
to establish a modem connection. If this happens you
will need to hang up for approximately 60 seconds before
trying again.
Once your PIN is validated, the following commands can be

Solution 16i
10 Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
performed. See the table below. If no keys are pressed for
20 seconds then the panel will play the exit jingle before
automatically terminating the session and hanging up.
Pressing [#] + [#] at any time while connected will cause
the control panel to terminate the session.
DTMF CONTROL FUNCTIONS
Operation Command Response
Quick Arm
All Areas 0+ #2 x Beeps
Log In
OK USER PIN + #Welcome
Jingle
Log In
Failed USER PIN + #Long Beep
Turn Area
ON 1+ (Area Nº1-4) + 1+ #2 x Beeps
(Low - High)
Turn Area
OFF 1+ (Area Nº1-4) + 2+ #2 x Beeps
(High - Low)
Turn
Output
ON
2+ (Output Nº1-8) + 1+ #2 x Beeps
(Low - High)
Turn
Output
OFF
2+ (Output Nº1-8) + 2+ #2 x Beeps
(High - Low)
End
Session #+ #Exit Jingle
Table 6: DTMF Remote Control Functions
DTMF EXAMPL ES
Examples below shows the log on step for clarity. In
practise is only necessary to log on once per DTMF control
session.
To turn Area 1 ON enter the following
2+ 5+ 8+ 0+ #= Log ON
1+ 1+ 1+ #= Arm Area 1
To turn Output 7 ON enter the following
2+ 5+ 8+ 0+ #= Log ON
2+ 7+ 1+ #= Turn Output 7 ON
To turn Output 3 OFF enter the following
2+ 5+ 8+ 0+ #= Log ON
2+ 3+ 2+ #= Turn Output 3 OFF
i
Note
If the DTMF Quick Arm option is programmed then it
is possible to remotely arm all areas without logging
onto the panel.
Simply enter [0] + [#] following the welcome jingle.
Make sure that the phone being used to remotely
control the panel is set to transmit DTMF tones when
keys are pressed during the call.
This option is disabled by default on some phones.
Programming Text Using The Keypad
When programming text via the keypad, each numeric key
represents a dierent group of characters.
Pressing the same numeric key again will move to the next
character assigned to the key (eg. Press the [2] key will
display the ‘A’ character, press the [2] key again will move
to the ‘B’ character, press the [2] key again will move to the
‘C’ character etc).
Once the required character is displayed, use the arrow
keys to move to the next letter of the word you are
entering. If you press a dierent key the system will assume
you are entering the next character in the word and it will
automatically step forward 1 position.
The key assignments and programming function are
identical to those found on most xed and mobile phones.
Refer to the table below for detailed character information.
Key Characters Assigned To Each Numeric Key
1 _ - @ . 1
2 A B C 2
3 D E F 3
4 G H I 4
5 J K L 5
6 M N O 6
7 P Q R S 7
8 T U V 8
9 W X Y Z 9
0 SPACE 0
Scroll Up through entire character list
Scroll Down through entire character list
Move to left one character position
Move to right one character position
OFF Clear from cursor postiion to end of line
Table 7: Text Character Set
To save programming changes, press [OK], or press [MENU]
to exit without saving.
The following additional special characters are
available by scrolling using the [] and [] arrow keys.
+ - @ # $ “ & % * : ( ) / < > =

11
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
System Pro grammi ng
i
Note
To enter programming mode simply enter your PIN
and press the MENU key on the keypad.
The default Master user PIN is 2580.
Access > PIN Codes > dEL-Ur
Erase User MENU 1-0-0
This command allows a master user to to erase another
user from the system. Erasing a user will remove the user’s
PIN, Proximity Token and RF keyfob credentials.
1. Ensure that the system (or area) is turned o.
2. Enter Master PIN + [MENU]
3. Enter [1] + [0] + [0] + [OK].
The keypad will display Ur = prompting you to enter
the number of the user to erase.
Ur=
4. Enter the user number then press [OK].
dEL ?
5. The keypad will now prompt you to conrm the
erasure by pressing [OK].
Access > PIN Codes > ch-PiN
Change Own PIN MENU 1-1-0
ThismenuletsyouchangeyourownPIN. Itisrecommended
that you write down your old PIN and the new one before
you begin. The new PIN must have the same number of
digits as your old PIN unless the variable PIN length option
has programmed by your installer. Once the change is
complete you should destroy the written copy.
At factory default, each PIN is xed to 4 digits in length.
1. Enter your PIN + [MENU]
2. Enter [1] + [1] + [0] + [OK].
The keypad will prompt you to enter a new PIN.
EntPin
3. Enter your new PIN, and then press [OK].
If an error tone sounds and the display reads “bAdPin”
you should try a dierent PIN. The keypad will now
prompt you to enter your new PIN again.
rEPEAT
4. To conrm your new PIN, enter your new PIN again.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving. Your PIN has now been changed.
Access > PIN Codes > ch-Oth
Change Other PIN MENU 1-1-1
This menu allows a master user to change somebody else’s
PIN. It is recommended that you write down the old PIN
and the new one before you begin. Once the change is
complete you should destroy the written copy. The new
PIN must have the same number of digits as the old PIN.
At factory default, each PIN is xed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580.
1. Enter your master PIN + [MENU]
2. Enter [1] + [1] + [1] + [OK].
The keypad will display Ur = prompting you to enter the
number of the user to change. Each user in the system
is assigned a user number as well as a PIN Number.
Ur=
3. Enter the user number to change then press [OK].
EntPin
4. Enter the new PIN.
If an error tone sounds, or “bAdPin” is displayed try a
dierent PIN.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes > AddPin
Add PIN MENU 1-1-2
This menu allows a master user to add a PIN for a new user.
Each master user can only program new PINs for those
users that have been assigned to the same area(s) as the
master user.
At factory default, each PIN is xed to 4 digits in length
however this can be changed by your installer to suit your
needs. The default PIN for User 1 (Master user) is 2580.
1. Enter your master PIN + [MENU]
2. Enter [1] + [1] + [2] + [OK].
The keypad will display the Ur = prompt.

Solution 16i
12 Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Ur=
3. Enter the user number that you want to add, then
press [OK].
If you select a user number which already exists, an
error beep will sound. If this happens select a dierent
user number.
EntPin
4. Enter the new PIN for the user you have selected.
If an error tone sounds, try a dierent PIN. The display
will show ==== as you enter the new PIN.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes > DELPin
Delete PIN MENU 1-1-3
This menu allows a master user the ability delete another
users PIN. A Master user can only delete a PIN for users that
have been assigned to the same area(s) as the Master user.
A Master user cannot delete their own PIN.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [1] + [3] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number you want to delete, then press
[OK].
Del ?
If you have selected a valid user, the system will ask you
to conrm the deletion.
4. Press [OK] to delete the PIN, or press [MENU] to
cancel.
Proximity Tokens & Cards
Proximity tokens and cards can be used as an alternative to
a PIN number when on and o the system.
A token is a small plastic tag card that has a unique ID. A
user can place the token card in front of a reader keypad to
turn the system or specic areas on and o.
This feature requires that at least one keypad that has an in-
build prox reader tted. This section outlines how to add
and delete proximity tokens or cards. If you try to add a
token from a keypad that does not have an in-built reader,
the keypad will prompt you to select the reader you wish
to learn the new token.
You should discuss this feature with your installer for more
details on your particular installation.
Access > Token > AddPrO
Add Token MENU 1-2-0
This menu allows a master user to add a new token for
other users provided they are assigned to the same area(s)
as the Master user.
This feature requires that at least one keypad that has an
in-build prox reader tted.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [2] + [0] + [OK].
The keypad will display the Ur = prompt.
Ur=
2. Enter the user number you want to add the token to,
then press [OK].
If you are currently using a keypad with built in reader
the system will prompt you to present the new token
to the keypad.
PrSEnt
2. Present the token at the keypad to learn the new
token.

13
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Access > Token > deLPrO
Delete Token MENU 1-2-1
This menu allows a master user to delete a users proximity
token or card. Master users can only delete user’s tokens
that belong to the same area.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [2] + [1] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number who’s token you want to
delete, then press [OK].
If you have selected a valid user with a token, the
system will ask you to conrm the deletion.
Del ?
4. Press [OK] again to delete the token, or press [MENU]
to cancel.
Access > Token > iD PrO
Token Status MENU 1-2-2
This menu allows a master user to identify which user
belongs to the token.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [2] + [2] + [OK].
The system will prompt you to present the token to be
identify to the keypad.
PrSEnt
3. Present the token to the keypad.
Once the token is presented the system will display the
user number who the token belongs to. In the example
below the token belongs to user 9.
Ur009
4. Press [OK] when nished.
RF Radio Keyfobs
Radio Keyfobs can be used as an alternate method for users
to turn an area(s) on and o and or control an automatic
door or gate.
This section outlines how to add and delete RF keyfobs
for users. The RF Keyfob must be compatible with the RF
Receiver that has been installed by your security company.
Access > RF Keyfob > AddFOb
Add Keyfob MENU 1-3-0
This menu allows a master user to program or learn a
keyfob ID number into the system.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [3] + [0] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number you want to add the keyfob
to, then press [OK].
The keypad will prompt you to enter the RF keyfob ID
number.
Ent id
4. Enter the RF Keyfob’s ID Number or alternatively
press any button on the keyfob to automatically
learn the ID number.
Access > RF Keyfob > dELFOb
Delete Keyfob MENU 1-3-1
This menu allows a master user to delete the RF keyfob that
has been assigned to a user.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [3] + [1] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number who’s keyfob you want to
delete, then press [OK].
dEL?
4. Press [OK] to delete the RF keyfob and exit.

Solution 16i
14 Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Access > User Properties > UrnAME
User Name MENU 1-4-0
This menu allows the master user to program the user’s
name. A maximum of 16 characters can be entered in this
eld. Use the [←]and [→]keys to scroll the cursor left and
right to view the entire user name.
The text programming procedure is very similar to that of
most mobile phones. Refer the Programming Text section
on page 10 for more details.
User names are stored with associated events in the
system’s history log. This enables accurate auditing of user
movements at a later time if required. Names are also used
when reporting alarms and arm /disarm events in SMS and
other text based reporting formats.
Each user has a default name which can be changed if
desired. The default names are as follows.
DEFAULT USER NAMES
User Number Default Name
1USEr 1 nAmE
2USEr 2 nAmE
↓ ↓
48 USEr 48 nAmE
Table 8: Default User Names
To change a user name,
1. Enter your Master PIN + [MENU].
2. Enter [1] + [4] + [0] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number who’s name you want to
change, then press [OK].
The keypad will display the current User Name.
USEr 5
The cursor position is displayed by the ashing
character in the name.
4. Use the 0 to 9, [←] and [→] keys to change the user
name text as required. At any time you can use the
[↑] and [↓] keys to scroll through the complete list of
available characters.
To clear all text from the cursor position to the right,
press the [OFF] key.
5. When the user name is complete, press [OK] to save
and exit, or press [MENU] to exit without saving.
Access > User Properties > UrArEA
Area Assignment MENU 1-4-1
This menu allows the master user to program which area(s)
(1 to 4) a user operate. The master user can only assign
another user to any one or multiple areas that the master
user has been assigned to. At factory default, each user is
assigned to operate Area 1.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [4] + [1] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number who’s area assignment you
want to change, then press [OK].
Zone numbers 1 to 4 area used to display which areas
that the user has access to.
-Bit-
1 2 4
4. Use keys [1] to [4] to toggle the area assignment on
or o.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Timer Groups
Timer Groups can be used to prevent various users from
operating the system outside given times of the day, days
of the week or even holiday periods.
This functionality can only be congured on your system
by the installer. Master users can assign other users to a
specic timer group as well as adjust the schedule start and
stop times and also the days of the week that the schedule
will operate.
Multiple schedules can be associated to a timer group,
however users can only belong to one timer group. For
example, to allow a group of users to operate the system
between 8am and 5pm on Mon,Tue,Wed and Fri, 1 schedule
(Sh1) is required. To allow operation between 8am and
9.30pm on Thu, a second schedule (Sh2) is required.
Once the schedule(s) have been created, your installer will
link them to a timer group, and advise you which timer
group number has been used.
Master users can now restrict the user(s), by linking them
to the appropriate timer group.

15
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Users
Each user can only belong to 1 timer group.
Schedules
Multiple schedules can be linked to the same timer group.
Up to 8 schedules can be created.
Time Groups
Up to 8 dierent timer groups can be created.
Access > User Properties > tMR grp
Timer Group MENU 1-4-4
This menu allows the master user assign each user to a
timer group. Timer groups can be used to restrict User
access to be within specic times dened by schedules.
Each user can only be assigned to one timer group. Setting
this option to 0 will give the user 24 hour access to the
system.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [4] + [4] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number you want to assign, then press
[OK].
d=00
4. Using the numeric keys (1 to 8 / 0 = disabled) , enter
the timer group number.
5. Press [OK] to save and exit or press [MENU] to exit
without saving.
Access > User Properties > Ur-Acc
Access Group MENU 1-4-5
This menu allows the master user to assign other users to
one or more access groups. An access group is used to
allow and/or restrict which users have access to various
system outputs. Outputs can be used to control doors,
gates or roller doors etc.
You should discuss these options with your installer.
1. Enter your Master PIN + [MENU].
2. Enter [1] + [4] + [5] + [OK].
The keypad will display the Ur = prompt.
Ur=
3. Enter the user number you want to assign, then press
[OK].
The keypad will display the current access groups
assigned to the user via the zone indicators.
-Bit-
1 2 4 5 6 8
4. Use keys [1] to [8] to toggle the corresponding access
groups on or o.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Areas
The Solution 16i control panel has the ability to be
partitioned up to 4 individual areas. Each area can be
independantly controlled. This section outlines various
commands that control individual areas.
Areas > Commands > L200
Area Status MENU 2-0-0
This menu allow users the ability toview the area status of
the current area or the status of a dierent area. This menu
is only available via a keypad who’s corresponding area is
turned o.
1. Enter [Master PIN] + [MENU]
2. Enter [2] + [0] + [0] + [OK].
If your system has been congured to have more than
one area, the keypad will display the A = prompt.
A=
3. Enter the number of the area that you want to view
the status of, then press [OK].
The keypad will display the area status information. If
the area is turned All On, the keypad will display:
ALL ON
If the area is turned All O, the keypad will display:
iS OFF
If the area is turned Part On, the keypad will display:

Solution 16i
16 Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
PArt 1
If the area is turned Part 2 On, the keypad will display:
PArt 2
4. To exit, press [OK].
Areas > Commands > L201
Turn Area On MENU 2-0-1
This menu allows you to turn a single area All On. If your
system has been congured to have multiple areas then
the keypad will prompt you to select the area you wish to
turn All On.
1. Enter your Master PIN + [MENU].
2. Enter [2] + [0] + [1] + [OK].
If your system has been congured to have more than
one area, the keypad will display the A = prompt.
A=
3. Enter the area number you wish to turn All On, then
press [OK].
Areas > Commands > L202
Turn All Areas On MENU 2-0-2
This menu allows you to turn on all areas that your PIN
has been assigned to at the same time All On. The keypad
displays below show the area icons 1 and 2 on indicating
that both Area 1 and Area 2 are armed.
1. Enter your Master PIN + [MENU]
2. Enter [2] + [0] + [2] + [OK].
The keypad will display the word “LEAVE” in the
display and the exit warning beeper will sound. You
should leave all areas now.
POWER
ON
When exit time has expired, the keypad will display
that the home area (Area 1 in this case) is on, and that
area 2 is also on via the area icons.
POWER
ON
AREA
i
Note
Area icons will only display if programmed to do so
by your security installer.
Areas > Commands > L203
Turn All Areas Off MENU 2-0-3
This menu allows you to turn o all areas that your PIN has
been assigned to at the same time. At least one keypad
on the system must be in a diasrmed area before you can
access this command.
1. Enter Master PIN + [MENU].
2. Enter [2] + [0] + [3] + [OK].
The system will now disarm all areas that are in the
armed condition provided the user belongs or has
access to the area.
Areas > Commands > L204
Move To Area MENU 2-0-4
This menu allows you to move the focus of a keypad’s
default home area to a dierent area. Once the keypad’s
focus has changed, you will be able to see the status of the
zones in that area and also perform functions as if you were
using the keypad located or assigned to that area.
1. Enter [Master PIN] + [MENU]
2. Enter [2] + [0] + [4] + [OK].
If your system has been congured to have more than
one area, the keypad will display the A = prompt.
A3 OFF
3. Enter the area number (1 to 4) that you want to move
to, then press [OK].
The keypad will now move to the requested area. If you
do not have acces to the selected area the system will
sound a error beep and the keypad focus will remain
un-changed.
The keypad will return to it’s home area, 30 seconds
after the last key press.
i
Note
If the keypad has been programmed to be a roaming
keypad then you can use the [←] and [→]keys to
move between areas at any time.

17
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Areas > Commands > chOnOF
Chime On/Off MENU 2-0-5
Chime mode allows you to monitor a zone (or group of
zones) while the system or area is in the disarmed state.
The system can be programmed to sound the keypad
buzzer or activate a programmable output when the
corresponding chime zone(s) are faulted. This feature can
be useful when you need to monitor the front or back
entrance to the premises.
This menu allows a user to turn chime mode on and o.
Only keypads programmed to sound the chime tone will
be heard when a zone programmed for chime is faulted.
The master user can program which zones are monitored
for chime alarms in MENU 3-0-3.
1. Enter your Master PIN + [MENU].
2. Enter [2] + [0] + [5] + [OK].
The system will display the current chime state. If your
system has been congured for multiple areas you will
be prompted to enter the area number to program.
In the example below chime mode “ IS OFF”.
iS OFF
3. To turn Chime mode on, simply press the [ON] key.
The display will show that chime mode “IS ON” and
also the chime icon will be displayed.
iS ON
To toggle chime mode off again, simply press [OFF].
4. Press the [OK] key to exit.
i
Note
It is possible to turn chime mode on and o pressing
the 4 key down for 2 seconds. Only the area currently
in focus will operate when using this method.
Areas > Commands > ch typ
Chime Mode MENU 2-0-6
Chime mode allows the master user to control the way
chime alarms operate. There are 4 options available.
1) Chime Always
Will sound the chime alarm while ever the zone(s)
programmed for Chime are open or faulted.
ch ALL
2) Chime One-Shot (Max 255 seconds)
Will sound the chime alarm for the programmed time
regardless of how long the chime zone(s) remains open or
faulted.
ch000
3) Delayed Chime (Max 255 seconds)
Will sound the chime alarm only after the chime zone(s)
has been open or faulted for the programmed time.
000ch
4) Chime Latching.
Will sound the chime alarm until a valid user code is entered
followed by the [OK] key. This will reset the Chime Alarm.
ch LAt
To set the chime mode.
1. Enter your Master PIN + [MENU].
2. Enter [2] + [0] + [6] + [OK].
If your system has been congured for multiple areas,
your keypad will prompt you to enter the area number
to program. The keypad will display the current chime
mode set for that area.
3. Use the [↑] and [↓] keys to select the required chime
mode.
If a time parameter is required for the chosen mode,
simply enter the require value in seconds.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.

Solution 16i
18 Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Areas > Area Properties > A-nAME
Area Name MENU 2-1-0
This menu allows you to program the name for each area.
The area name can be up to 16 characters long. At factory
default, only Area 1 is used. The control panel can have a
maximum of 4 independent areas programmed.
1. Enter your Master PIN + [MENU].
2. Enter [2] + [1] + [0] + [OK].
The keypad will prompt you to enter the area number
of the area that you want to change the name for.
A=
3. Enter the area number (1 to 4), then press [OK].
The keypad will display the rst six characters of the
current area name.
4. Use the [0] to [9], [←] and [→] keys to change the
area name text as required.
At any time you can use the [↑] and [↓] keys to scroll
through the complete list of available characters.
To clear all text from the cursor position to the right,
press the [OFF] key.
5. When the area name is complete, press [OK] to save
and exit, or press [MENU] to exit without saving.
DEFAULT AREA NAMES
Area Number Default Name
1Secvrity System
2AreA 2
3AreA 3
4AreA 4
Table 9: Default Area Names
Input Options
The control panel can have up to a maximum of 16 zones.
When the optional radio receiver is tted, any available
zone can be programmed as a wireless zone. Your installer
will advise you on the exact makeup and conguration of
your system.
Inputs > Commands > stAtus
Zone Status MENU 3-0-0
This menu allows you to view the status or condition of
each zone on the system. There are four possible states
which can be displayed, Zone Normal, Zone Open, Zone
Tamper and Zone Shorted. The status display will also
show the resistance accross the zone loop.
1. Enter your Master PIN + [MENU].
2. Enter [3] + [0] + [0] + [OK].
The keypad will display the Zn = prompt.
Zn=
3. Enter the zone number you want to view the status
of, then press [OK].
The keypad will scroll the zone status information. The
rst screen will display the zone state.
There are 4 possible states;
Normal - Zone is closed and ready.
Short - Zone is shorted and not ready.
Open - Zone is open and not ready.
Tamper - Zone tamper circuit is open.
NORMAL
The keypad will now display the zone resistance in
ohms. This resistance is measured by the control panel.
03198
4. Press the [OK] key to exit.

19
Bosch Security Systems 6/09 BLCC500U FTR1.03
Solution 16iUser Guide
Inputs > Commands > BypAss
Bypass Zones MENU 3-0-2
This menu allows you to bypass one or more zones before
you turn an area All On, Part On or Part 2 On. When a zone
is bypassed, it is not able to detect intrusion or sound an
alarm. All non bypassed zones will continue to operate as
normal.
Any zone that has been bypassed will automatically be un-
bypassed when you turn the corresponding area o.
1. Enter your Master PIN + [MENU].
2. Enter [3] + [0] + [2] + [OK].
The keypad will ash the Zn= prompt. Any zone(s)
which are currently bypassed will also be ashing.
If your system is programmed for multiple areas, the
area icon will also be displayed.
Zn= 1
3 4
3. To bypass a zone, enter the zone number and then
press [OK] .
The zone indicator will begin to ash. To un-bypass a
zone type the zone number and then press [OK].
Repeat step 3 for any additional zones that you need to
bypass or un-bypass.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
i
Note
You can only bypass zones in the current area.
To bypass zones in another area, exit progamming
mode and move to the required area before
repeating from step 1.
i
Note
You can also access the Zone Bypass function by
entering your PIN and then pressing the PART /
Bypass key down for 2 seconds.
Inputs > Commands > ch-zn
Set Chime Zones MENU 3-0-3
This menu allows you to program zones to be monitored
when the corresponding area is turned o. Chime mode is
ideal to monitor a front door to sound the keypad buzzer
when opened (faulted).
1. Enter your Master PIN + [MENU].
2. Enter [3] + [0] + [3] + [OK].
The keypad will ash the Zn= prompt, indicating
that you are in data entry mode. Any zone(s) which
are currently set as Chime Zones will be displayed.
An area icon will also display to verify which area you
are programming chime zones for.
Zn= 1
1 3
3. Enter the zone number (1 to 16) followed by the [OK]
key to toggle the zone on or o for chime mode.
Repeat step 3 toggle chime zones on or o.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Inputs > Commands > Pt2-zn
Set Part 2 Zones MENU 3-0-4
This menu allows you to program which zones are to be
monitored when an area has been turned Part 2 On.
At factory default all zones are monitored when you turn
the area Part 2 On.
1. Enter your Master PIN + [MENU].
2. Enter [3] + [0] + [4] + [OK].
The keypad will display the Zn= prompt.
Any zone(s) that are programmed not to be monitored
when you turn the area Part 2 On will not be displayed.
An area icon will also display to verify which area you
are programming chime zones for.
Zn= 1
1 2 3 5 7 8
3. Enter the zone number (1 to 16) followed by [OK] to
toggle the monitoring of the zone on or o when
turned Part 2 On.
Repeat Step 3 for any additional Part 2 zones you
require.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
i
Note
In the above example, zones 1,2,3,5,7 and 8 will be
monitored when the Area 1 is turned Part 2 On.
Zones 4 and 6 will not be monitored.

Solution 16i
20 Bosch Security Systems 6/09 BLCC500U FTR1.03
User Guide
Inputs > Commands > fire-r
Smoke Sensor Reset MENU 3-0-5
If your system has smoke sensors tted, they may be
powered directly by the control panel. If this is the case,
this menu is used to reset your smoke detectors when
required.
1. Enter your Master PIN + [MENU].
2. Enter [3] + [0] + [5] + [OK].
Busy
The keypad will display the word BUSY for 10 seconds
while the smoke sensors are reset before returning to
the menu.
i
Note
If your system is congured for multiple areas you
may be asked to select the area to reset.
Inputs > Zone Properties > znnAME
Zone Name MENU 3-1-0
This menu allows the master user to program name of each
zone (Up to 16 characters). Use the [←]and [→]keys to
move the cursor position left and right to view the zone
name.
The text programming procedure is very similar to that of
most mobile phones. Refer the Programming Text section
on page 10 for more details.
Zone names are stored with associated events in the
system’s history log. This enables accurate auditing of
events at a later time if required. Names are also used
when reporting alarms and turning an area on and o in
SMS and other text based reporting formats.
Each zone has a default name which can be changed if
desired. The default names are as follows.
DEFAULT ZONE NAME S
Zone Number Default Name
1ZOne 1
2ZOne 2
↓ ↓
16 ZOne 16
Table 10: Default Zone Names
1. Enter your Master PIN + [MENU].
2. Enter [3] + [1] + [0] + [OK].
The keypad will display the Zn = prompt.
Zn=
3. Enter the zone number you want to program, then
press [OK].
The keypad will display the current Zone Name.
Zone 1
4. Use the [0] to [9], [←] and [→] keys to change the
Zone Name text as required.
At any time you can use the [↑] and [↓] keys to scroll
through the complete list of available characters.
To clear all text from the cursor position to the right,
press the [OFF] key.
5. When the Zone Name is complete, press [OK] to save
and exit, or press [MENU] to exit without saving.
Inputs > Input Testing > tstzns
Walk Test All Zones MENU 3-9-0
This menu allows you to test all zones within an area at the
same time. To successfully walk test each zone, you must
open and close each zone.
1. Enter your Master PIN + [MENU].
2. Enter [3] + [9] + [0] + [OK].
The keypad will display a list of all zones to be tested.
If your system is congured for multiple areas then you
may be prompted to select the area to test.
test
1 2 3 4 5 6 7 8
3. Fault and restore each zone that needs to be tested.
A zone that has been successfully tested will no longer
be displayed on the keypad display.
When all zones have been tested, the keypad will
display PASS.
PASS
4. Press [OK] to exit