Bradley S96-051 User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
6951 Multi-Station
Wall Sink
S96-051 (6951A-5) 5 station
S96-106 (6951B-5) 5 station
S96-080 (6951A-4) 4 station
S96-107 (6951B-4) 4 station
S96-083 (6951A-3) 3 station
S96-108 (6951B-3) 3 station
S96-085 (6951A-2) 2 station
S96-109 (6951B-2) 2 station
Table of Contents
Safety Information ...............................2
Supplies Required for Installation ...................3
Wall Sink Components ...........................3
2-& 3-Station Wall Sink Rough-Ins ..................4
4-& 5-Station Wall Sink Rough-Ins ..................5
Installation Instructions ......................... 6-7
Cleaning Stainless Steel ..........................7
Faucets by Others
215-737 Rev. G: ECO 19-00-028
© 2019 Bradley
Page 1 of 7 9/10/2019
Read the instructions in this manual before
beginning installation. Save these instructions
and refer to them for inspection, maintenance
and troubleshooting information.
For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com
or call 800.BRADLEY (800.272.3539).
Product warranties and parts information may also be found under "Products" on our website at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material.
If any parts are missing, do not begin installation until you obtain the missing parts.

6951 Series Installation
29/10/2019 Bradley • 215-737 Rev. G: ECO 19-00-028
Safety Information
Installation
Compliance and conformity to local codes and ordinances is the responsibility of the installer.
Product/Property Damage
Make sure that all water supply lines have been flushed and then completely turned off before beginning installation.
Debris in the supply lines can cause valves to malfunction.

Installation 6951 Series
Bradley • 215-737 Rev. G: ECO 19-00-028 9/10/2019 3
Supplies recommended for installation
• 1-1/4" anchors and bolts to secure sink to wall
• Wall reinforcement (if required)
• Trap and drain pipe to 1/-1/2" O.D. tailpiece
• Supply pipe to faucets (if required)
• OPTIONAL: 1/4" anchors and bolts to secure footing to floor
Wall Sink
3-Station (S39-374) shown above, others similar
Wall sinks are 2, 3, 4 or 5 stations and can be manufactured
with 4" centerset or single hole shank faucet mounting. All
faucet mounting holes are 1-1/4" diameter.
1/4"-20 x 3/8"
Socket-Head
Set Screw
(160-246)
Leg (Pipe)
(113-744)
Support Bracket
(140-112)
2- and 3-Station (qty. 2)
4-Station (qty. 3)
5-Station (qty. 4) Drain Spud
(112-028)
Washer
(142-063)
Oval-Head
Screw
(160-042)
Tailpiece
(S29-083)
Adjustable
Footing
(S36-020)
Locknut
(161-148)
Strainer
(173-002)
Components

6951 Series Installation
49/10/2019 Bradley • 215-737 Rev. G: ECO 19-00-028
23-1/2" - 25"
(597) (635)
3'-6" or 42"
(1066)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
1'-9" or 21"
(533)
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
5'-2" or 62"
(1574)
2'-7" or 31"
(787)
2-Station Wall Sink
Dimensions
3-Station Wall Sink
Dimensions
Dimensions

Installation 6951 Series
Bradley • 215-737 Rev. G: ECO 19-00-028 9/10/2019 5
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
8'-6" or 102"
(2591)
4'-3" or 51"
(1295)
23-1/2" - 25"
(597) (635)
43" - 44-1/2"
(1092)(1130)
31"-32-1/2"
(787)(826)
18"
(457)
6'-10" or 82"
(2082)
3'-5" or 41"
(1041)
4-Station Wall Sink
Dimensions
5-Station Wall Sink
Dimensions
Dimensions

6951 Series Installation
69/10/2019 Bradley • 215-737 Rev. G: ECO 19-00-028
1. Install suitable wall anchors for 1/4" bolts at the dimensions
shown in the rough-in drawings (anchors and bolts supplied
by installer).
• 2- and 3-station sinks require 10 wall anchors and bolts.
• 4-station sink requires 13 wall anchors and bolts.
• 5-station sink requires 16 wall anchors and bolts.
2. Use a carpenter’s level to make sure all of the brackets are
level with the floor and with each other before securing them
to the wall. An improperly installed bracket could result in a
sink that is not level.
3. Mount the support brackets to the wall anchors with 1/4" bolts
(supplied by installer).
• 2- and 3-station sinks require two brackets and six bolts.
• 4-station sink requires three brackets and nine bolts.
• 5-station sink requires four brackets and twelve bolts.
4. Hang the wall sink onto the support brackets.
Make the connection to the pipe (supplied by the installer)
AFTER the sink legs have been installed.
1. Use plumbers putty to caulk the drain spud.
2. Insert the drain spud into the hole in the wall sink and secure the
spud to the sink with the washer and locknut provided as shown.
3. Attach the strainer to the drain spud and secure with the two
screws provided.
4. Insert the flanged plastic washer into the top of the tailpiece.
Slide the tailpiece nut up to the top of the tailpiece and screw the
nut into the spud to secure the tailpiece to the sink.
Mount Sink to Wall
1
Assemble Drain
2

Installation 6951 Series
Bradley • 215-737 Rev. G: ECO 19-00-028 9/10/2019 7
1. Screw the adjustable footings into the bottom of the legs.
2. Insert the legs into the sink flanges located at the underside of the
sink. Secure the legs with the setscrews provided.
3. Adjust the foot pads on the bottom of the legs to level the unit and
provide proper drainage.
1. Secure the sink to the wall with four 1/4" bolts (supplied by installer)
through the wall anchors installed in Procedure #1.
2. OPTIONAL FAUCETS: Make the proper supply connections to the
faucets as outlined in the faucet manufacturer’s installation manual.
3. Make the drain connection to the 1-1/2" O.D. tailpiece on the sink (pipe
supplied by installer).
Attach Legs and Footings
3
Complete Installation
4
Cleaning and Maintenance Instructions for Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care,
particularly under corrosive conditions, is essential. Always start with the simplest solution and work your way toward
the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply
the cleaning solution per the manufacturer’s instructions and always use a soft cloth or sponge to avoid damaging the
finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®
stainless steel cleaner or a soft abrasive. Always follow the manufacturer’s instructions and apply in the same
direction as the polish lines.
NOTICE! Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool
or stainless steel brushes.