Bradley S19-120SSBF User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
215-1262 Rev. F; ECN 08-517
© 2008 Bradley Corporation
Page 1 of 4 8/11/08
S19-120SSBF
Stainless Steel Drench Shower -
Horizontal Supply
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly of Components and Parts List . . . . . . . . . . 4

2
S19-120SSBF Installation
8/11/08 Bradley Corporation • 215-1262 Rev. F; ECN 08-517
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to the
eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized
shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI
Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to ensure
compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per
ANSI Z358.1.
For questions regarding the operation or installation of this product, visit www.
bradleycorp.com or call 1-800-BRADLEY.
Product warranties and service parts information may also be found under ”Products”
on our web site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
P.O.Box309,MenomoneeFalls,WI53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetriebprüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

3
Installation S19-120SSBF
Bradley Corporation • 215-1262 Rev. F; ECN 08-517 8/11/08
Installation
Supplies Required:
• Pipe sealant
• Piping to 1" NPT water supply inlet
• Adequate supply pipe supports
• Minimum 4" (102 mm) drain to accommodate
30 gallons (115 liters) per minute discharge for
shower waste
• Sign-mounting hardware
Step 1: Assemble components
1. Assemble components as shown on page 4.
• Apply pipe sealant (supplied by installer) to
all male-threaded pipe joints.
• Thread the jam nut onto the threaded end
of the pull rod. Thread the pull rod onto
the coupling and tighten the jam nut. The
triangular end of the pull rod must be in
line with the hook end (see page 4).
• The bottom edge of the showerhead
should be 7'-0" (2134 mm) from the floor.
Step 2: Connect water supply
IMPORTANT: Do not rely on Bradley’s
Drench Shower to support supply
piping.
1. Connect water supply piping to 1" NPT inlet
on unit (piping supplied by installer). Provide
adequate supports (supplied by installer)
for supply pipe using pipe hangers or other
means.
2. Mount the safety sign to the wall using sign-
mounting hardware supplied by installer.
8"
(203mm)
min. to
wall
9"
(229mm)
45"
(1142mm)
24"
(610mm) 3-5/8"
(92mm)
3.7"
(94mm)
7'-0"
(2134mm)
to Floor

4
S19-120SSBF Installation
8/11/08 Bradley Corporation • 215-1262 Rev. F; ECN 08-517
Assembly of Components
Parts List
1 S30-061 1 Stay-Open Ball Valve Assembly
1.1 128-142 1 Handle
1.2 S27-276 1 Ball Valve with Jam Nut
1.21 161-079 1 Jam Nut (only)
2 113-864 1 Pipe 1" NPT x 21" Long
3 169-1074 1 90° Elbow 1" NPT
4 S24-191 1 Stainless Steel Showerhead Assembly
4.1 S24-187 1 Flow Control Assembly, 23 GPM
5 151-001 2 Curtain Hook
6 S90-365D 1 Pull Rod, 45"
6.1 161-026 1 Nut, 1/4"-20
7 204-421 1 Emergency Tag
8 114-050 1 Safety Sign
Item Part No. Qty Description Item Part No. Qty Description
1" NPT
Supply Inlet
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O.BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-050
44.1
7
8
6
5
2
3
1.1
1.21
1.2
1
ALIGN
HANDLE
PIECES
AS SHOWN
NOTE: Items 1.1–1.2 come preassembled as Item 1.