Bradley S19-210SC User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Installation
215-155SC Rev. L; EN 06-532D
© 2007 Bradley Corporation
Page 1 of 5 6/20/07
S19-210SC
Pedestal-Mounted Stainless
Steel Eyewash with Dust Cover
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . .3
Assembly of Components . . . . . . . . . . . . . . . . .4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2
S19-210SC Installation
6/20/07 Bradley Corporation • 215-155SC Rev. L; EN 06-532D
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
!
!
!
!
P.O.Box309, MenomoneeFalls, WI 53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

3
Installation S19-210SC
Bradley Corporation • 215-155SC Rev. L; EN 06-532D 6/20/07
Installation
NOTE: Flush the water supply line
before beginning installation.
Supplies Required:
• (3) 3/8" floor anchors and bolts
• Pipe sealant
• Piping to 1/2" IPS water supply
inlet on unit
• Piping to 1-1/4" IPS drain outlet for
eyewash
• Sign-mounting hardware
Step 1: Secure base and
brackets to floor
1. To secure base to floor, install
three suitable anchors (supplied
by installer) for 3/8" bolts in the
floor (Figure 1).
2. Bolt the base to the floor anchors
using 3/8" bolts (supplied by
installer).
Step 2: Assemble eyewash
components
1. Assemble eyewash components as
shown in Figure 2 on page 4.
• Apply pipe sealant (supplied by
installer) to all male-threaded
pipe joints.
• Use the rubber grip pad
provided or a strap wrench
around pipes when tightening
to prevent marring. Place the
grip pad on the pipe, then put
the wrench over the grip pad
and turn the pipe with the
wrench.
Step 3: Connect water supply
1. Connect the water supply piping (supplied by installer) to the 1/2" IPS inlet on the eyewash.
2. Connect the drain piping (supplied by installer) to the 1-1/4" IPS drain outlet on the eyewash.
3. Mount the safety sign to the wall using sign-mounting hardware (supplied by installer).
4. Open the water supply lines. Test for leaks and adequate water flow.
7-1/4"
(184mm)
21-1/2"
(546mm)
40-1/2"
(1029mm)
5-1/4"
(133mm)
35"
(889mm)
6"
(152mm)
8-3/4"
(222mm)
Ø 10-3/4"
(273mm)
17-1/4"
(438mm)
Figure 1
NOTE: All dimensions assume standard thread
engagement. Variations in manufacturing allow
for +/- 1/8" (3mm) per threaded joint. To find
the tolerance of a dimension, add the number
of thread joints in between a dimension and
multiply it by 1/8" (3mm).

Assembly of Components
4
S19-210SC Installation
6/20/07 Bradley Corporation • 215-155SC Rev. L; EN 06-532D
P.O.Box 309, Menomonee Falls, WI 53051
R
TESTTHISUNIT EACHWEEK
Test-operate valve(s) each week and sign below.
Report any malfunctionsimmediately.
Ventil(e) wöchentlichim Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störungsofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement desvalveschaque semaine et
signe en bas. S'il y à quelque chose qui ne va pasfait
un rapport immédiatement.
P.O. B OX 309, MENOMONEE FALLS,W I 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051
4.7
4.5
Flow Control
ThisEnd
4.4
4.3
4.2
4.1
5
7
9
7.1
1/2" IPS
Supply Inlet
3
10
2
1
6
1-1/4" IPS
Drain Outlet
4.11
4.12
4.8
4.9
4.10
4
HANDLE NOTE:
Close the cover and
put the pin through
the clip to keep closed.
4.6
12
8
Figure 2 NOTE: Items 4.1–4.12 come preassembled as Item 4.
Items 8.1–8.5 come preassembled as Item 8.

5
Installation S19-210SC
Bradley Corporation • 215-155SC Rev. L; EN 06-532D 6/20/07
Parts List
1 131-062 1 Base
2 269-237 1 Pipe Tee 1-1/4"
3 113-584 1 Pipe Tee 1-1/4" x 26-1/2"
4 S90-319 1 Eyewash w/Dust Cover
4.1 111-049 1 Inlet Drain Fitting
4.2 124-028 1 Center Seal Gasket
4.3 S90-009 1 Dust Cover Assembly
4.4 173-009 1 Cup Strainer
4.5 S21-072 1 Supply Pipe
4.6 113-1159 1 Spacer, Drain
4.7 S05-131 1 Eyewash Yoke
4.8 115-141 2 Sprayhead
4.9 153-333 1 Pipe Plug
4.10 269-874 1 Cap Plug
4.11 269-447 1 Bumper
4.12 161-025 1 Nut, Hex
5 113-965 1 Pipe, Stainless Steel 1/2" x 3-1/2"
6 269-241 1 Street Elbow 1/2"
7 S27-287 1 Stay-Open Ball Valve w/Nut
7.1 161-151 1 Nut Only
8 S08-337 1 Flag Handle Assembly
9 114-051 1 Safety Sign
10 204-421 1 Emergency Inspection Tag
11 269-915 1 Grip Pad (not shown)
12 142-002DA 1 Washer
Item Part No. Qty Description Item Part No. Qty Description
Prepack S45-1787 includes Items 4.2, 4.4, 4.5, 4.6