Bradley S96-050 User manual

P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1.800.BRADLEY Fax: [phone]
bradleycorp.com
215-1430 Rev. B; ECN 10-02-010
© 2011 Bradley Corporation
Page 1 of 3 1-28-2011
Bradley Multi-Station
Island Sink
Model S96-050 (6950A)
Table of Contents
Supplies Required ...........................2
Island Sink Components......................2
Island Sink Dimensions.......................2
Installation Instructions .......................3
Cleaning Stainless Steel......................3
Installation
Faucets by others
IMPORTANT!
Read this entire installation manual to ensure proper installation. When
finished with the installation, file this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for
before discarding packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then completely
turned off before beginning installation. Debris in supply lines can cause
valves to malfunction.
Product warranties may be found under “Products” on our web site at
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•

Bradley Multi-Station Island Sink Model Nos. S96-050 (6950A) Installation
21-28-2011 Bradley Corporation • 215-1430 Rev. B; ECN 10-02-010
Supplies recommended for installation:
• 1/4" anchors and bolts to secure sink to floor
• Trap and drain pipe to 1/-1/2" O.D. tailpiece
• Supply pipe to faucets (if required)
LOCKNUT
(161-148)
OVAL-HEAD
SCREW
(160-042)
WASHER
(142-063)
DRAIN SPUD
(112-028) STRAINER
(173-002)
TAILPIECE
(S29-083)
TAILPIECE PREPACK S45-1804
Model 6950A Dimensions
(mm)
30"
(762)
6"
(152)
72"
(1829)
49"
(1245)
11-1/2"
(292)
60"
(1524)
32-1/2"
(826)
– 34"
(864)
7"
(178)
4"
(102)
12"
(305)
20"
(508)
8-Station Island Sink Model S96-050
(shown with faucets by others)

Installation Bradley Multi-Station Island Sink Model Nos. S96-050 (6950A)
Bradley Corporation • 215-1430 Rev. B; ECN 10-02-010 1-28-2011 3
Cleanliness is of utmost importance. Do not permit salty solutions to evaporate and dry on stainless steel. Never use
ordinary steel wool or steel brushes on stainless steel. Always use stainless steel wool or stainless steel brushes.
Use a carpenter’s level to make sure that the sink is level with the floor before installing anchors.
1. Remove ordinary deposits of dirt and grease with soap and water. Whenever possible, the metal should be thoroughly rinsed
and dried after washing.
2. Use stainless steel polishing powder to get rid of tightly adhering deposits.
3. Look for the source of the rust in some iron or steel not actually a part of the stainless steel structure. Sometimes the
appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. A steel nail or screw may be
the cause of the trouble.
4. If the sprayhead delivers an uneven spray, remove the sprayhead from the unit, disassemble, and remove foreign matter.
Reassemble sprayhead and reinstall into unit.
Cleaning Stainless Steel
1Level the Sink
2Assemble the Drain and Complete Installation
1. Adjust the foot pads on the bottom of the legs to level the unit and provide
proper drainage.
2. Secure the foot pads to the floor with suitable anchors and hardware (supplied
by installer).
1. Insert the drain spud into the hole in the island sink and secure the spud
to the sink with the washer and locknut provided as shown.
2. Attach the strainer to the drain spud and secure with the two screws
provided as shown.
3. Insert the flanged plastic washer into the top of the tailpiece. Slide the
tailpiece nut up to the top of the tailpiece and screw the nut into the spud to
secure the tailpiece to the sink.
4. Install the faucets as outlined in the faucet manufacturer’s installation manual.
5. Make the proper supply connections to the faucets as outlined in the faucet
manufacturer’s installation manual (pipe supplied by installer).
6. Make the drain connection to the 1-1/2" O.D. tailpiece on the sink (pipe
supplied by installer).
Make the connection to the pipe (supplied by the installer) AFTER
the sink has been levelled.
To avoid leakage, use plumber’s putty to caulk the drain spud.