Bradley S19-210SS User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
215-604 Rev. U; EN 06-532G
© 2007 Bradley Corporation
Page 1 of 5 6/21/07
S19-210SS
Pedestal-Mounted Stainless
Steel Eyewash with Foot Pedal
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . .3
Assembly of Components . . . . . . . . . . . . . . . .4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation

2
S19-210SS Installation
6/21/07 Bradley Corporation • 215-604 Rev. U; EN 06-532G
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
!
!
!
!
P.O.Box309, MenomoneeFalls, WI 53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

Installation
NOTE: Flush the water supply line before
beginning installation.
Supplies Required:
• (3) 3/8" floor anchors and bolts
• Pipe sealant
• Piping to 1/2" IPS water supply inlet on unit
• Piping to 1-1/4" IPS drain outlet for eyewash
• Sign-mounting hardware
Step 1: Secure base to floor
1. Install three suitable anchors (supplied by
installer) for 3/8" bolts in the floor (see
Figure 1).
2. Bolt the base to the floor anchors using 3/8"
bolts (supplied by installer).
Step 2: Assemble eyewash
1. Assemble eyewash components as shown in
Figure 2 on page 4.
• Apply pipe sealant (supplied by installer)
to all male-threaded pipe joints.
• Use the rubber grip pad provided or a strap
wrench around pipes when tightening to
prevent marring. Place the grip pad on the
pipe, then put the wrench over the grip pad
and turn the pipe with the wrench.
• When connecting the chain, first connect
the chain to the foot treadle “S” hook on
the valve handle. Make sure the chain is
pulled tight (the length of chain used will vary).
Step 3: Connect water supply
1. Connect the water supply piping (supplied by installer) to the 1/2" IPS inlet on the eyewash.
2. Connect the drain piping (supplied by installer) to the 1-1/4" IPS drain outlet on the eyewash.
3. Mount the safety sign to the wall using sign-mounting hardware (supplied by installer).
4. Open the water supply lines. Test for leaks and adequate water flow.
3
Installation S19-210SS
Bradley Corporation • 215-604 Rev. U; EN 06-532G 6/21/07
15-3/8"
(391mm)
35"
(890mm)
40-3/4"
(1035mm)
5-1/8"
(130mm)
6"
(152mm)
Figure 1
NOTE: All dimensions assume standard thread
engagement. Variations in manufacturing allow
for +/- 1/8" (3mm) per threaded joint. To find
the tolerance of a dimension, add the number
of thread joints in between a dimension and
multiply it by 1/8" (3mm).

Assembly of Components
4
S19-210SS Installation
6/21/07 Bradley Corporation • 215-604 Rev. U; EN 06-532G
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11 4.12
2
3
4
9.3
10
1
P.O. BO X 309,MENOMONEE FALLS, WI 53052-0309USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
P.O. Bo x 309, Menomonee Falls,W I 53051
R
TESTTHISUNIT EACH WEEK
Test-operate valve(s)each week and sign below.
Reportany malfunctionsimmediately.
Ventil(e)wöchentlich im Testbetriebprüfen, bestätigt
durchUnterschrift. Jegliche Störungsofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAIHEBDOMADAIRE
Test le fonctionnementdesvalveschaque semaine et
signeen bas. S'il y à quelque chose qui ne va pasfait
unrapport immédiatement.
5
6
9.7
9.8
9.6
9.1 9.5
9.4
9.2
9.1
1-1/4" IPS
DRAIN OUTLET
7
7.1
13
8
1/2" IPS
SUPPLY INLET
FLOW CONTROL
THISEND
9
11
NOTE: Items 4.1–4.12 come preassembled as Item 4.
Figure 2

5
Installation S19-210SS
Bradley Corporation • 215-604 Rev. U; EN 06-532G 6/21/07
Parts List
1 131-062 1 Base
2 269-237 5 Pipe Tee 1-1/4" IPS
3 113-584 1 Pipe 1-1/4" IPS x 26-1/2"
4 S90-317 1 Stainless Steel Spray Ring Assy.
4.1 111-049 1 Inlet-Drain Fitting
4.2 124-028 1 Center Seal Gasket
4.3 187-053 1 Stainless Steel Bowl
4.4 173-009 1 Cup Strainer
4.5 S21-074 1 Supply Pipe
4.6 113-1159 1 Spacer, Drain
4.7 S05-131 1 Eyewash Yoke
4.8 107-371 2 Dust Cover
4.9 269-912 1 Swivel Stem
4.10 124-055 2 Quad Ring
4.11 S57-148 1 Spray Ring Assembly
4.12 110-209 1 Acorn Nut
5 113-965 1 Pipe, Stainless Steel 1/2" x 3-1/2"
6 269-241 1 Elbow
7 S27-287 1 1/2" Ball Valve with Jam Nut
7.1 161-151 1 Jam Nut only
8 S08-338 1 Handle Assembly
9 S45-1314SS 1 HFSO Prepack
9.1 269-646 2 “S” Hook
9.2 134-009A 1 Stainless Steel Chain
9.3 181-008SS 1 Treadle
9.4 160-401 1 Screw
9.5 161-137 1 Nut, Acorn
9.6 147-026 1 Eye Bolt
9.7 142-002BT 1 Lockwasher
9.8 161-025 1 Hex Nut
10 114-051 1 Safety Sign
11 204-421 1 Emergency Tag
12 269-915 1 Grip Pad (not shown)
13 142-002DA 1 Lockwasher
Item Part No. Qty Description Item Part No. Qty Description