BraunAbility Turny HD User manual

Turny HD Turny Orbit
SV 4Bruksanvisning
EN 20 User manual
DE 36 Gebrauchsanweisung
FR 52 Instructions d’utilisation
ES 68 Instrucciones de uso
IT 84 Istruzioni per l’uso
Turny
Seat lift

20
Turny
from BraunAbility!
The following manual is an important part of the product, providing you with
information on how to achieve maximum performance and safe operation. Keep the
manual in a safe place so that you can refer to it when necessary.
If you have any questions about your adaptation, please contact your installation
engineer. If you want to know more about us and our range of car adaptation
solutions visit www.braunability.eu.
Once again, thank you for placing your confidence in our products!
Thank you for choosing a
Turny

Safety
22 Safety measures
Operation
24 Hand control
26 Manoeuvring outwards and inwards
Emergency-mode operation
28 Raise Turny Orbit/HD
30 Rotate the Turny Orbit inwards
Care instructions
32
Troubleshooting
33
Technical specification
34
Introduction for users
35
21
EN
Index
“Product certificate” at the end of the manual.
Turny

Safety measures
Turny
22
Safety

Getting up
Turny can be used as a lifting aid for the user, if at the same a
helper carefully moves the seat upwards, see illustration.
Transferring to and from wheelchair
A transfer between car seat and wheelchair, or vice versa,
becomes easier if the transfer is made from a higher to a
lower position. By adjusting the Turny’s height an optimal
transfer position can be achieved.
Turny 23
EN
Safety

OUT /
In order to rotate outwards and lower Orbit, or lower HD, keep the left-hand but-
ton in. To interrupt the movement, release the button.
IN /
In order to raise and rotate Orbit inwards, or raise HD, keep the right-hand button
in. To interrupt the movement, release the button.
When the green LED is constantly lit, Turny is in a safe position for driving.
When the green LED is blinking, Turny is not in a safe position for driving.
• The standard model Turny is supplied with a cable connected hand control unit.
Turny can be manoeuvred via a wireless hand control unit, available as an optional
extra.
• For safety reasons the Turny can only be manoeuvred when the vehicle is
stopped and/or the door is open.
• When not in use place the hand control in its holder.
Hand control
IN
OUT
IN
OUT
Turny
24
Operation

Hand control messages during normal operation.
Message Cause
No diode lit The vehicle's engine is switched on and/or the door is closed. Turny cannot be
manoeuvred.
Green LED blinks slowly Energy-saving mode.
Green LED lit Rotated inwards to end position. Turny is in a safe position for driving.
Green LED blinks Not rotated inwards to end position. Turny is not in a safe position for driving.
Red LED lit
Green LED blinks
End position reached and cannot be further lowered.
Red LED lit
Green LED blinks slowly
Has reached the end position and is in energy saving mode.
Turny 25
EN
Operation

Rotate outwards
Turny Orbit
Turny HD
Lower
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
Grip the seat. Pull the release lever upwards and
rotate the seat outwards to its locked end position.
Lower the seat to the desired height.
Turny
26
Manoeuvring outwards and inwards

Raise Rotate inwards
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
Turny Orbit
Turny HD
Grip the seat. Pull the release lever upwards and
rotate the seat inwards to its locked end position.
When the green LED is constantly lit, Turny is in a safe
position for driving.
Turny 27
EN
Operation

Raise Turny Orbit/HD
Take out the crank axed to the plate behind the back support.
Insert the crank behind the hexagonal keyhole at the Turny’s rear
section and fully crank the seat in.
2 cm
Option A - easy but slow
Turny
28
Emergency-mode operation

Remove the two cotter pins behind the seat. Lift and then push
the chair all the way in. Be firm but careful.
Option B - dicult but quick
Turny 29
EN
Emergency-mode operation

Rotate the Turny Orbit inwards
Use the yellow release lever at the front of the Turny.
1Depress and push the lever to the side to release the
seat. Push the lever to the right on a right model and
to the left on a left model.
2
Turny
30

Rotate the seat fully in. Then move the lever to its
original position to lock the seat in position.
3
Turny 31
EN
Emergency-mode operation

If necessary.................................................................
Once a year................................................................
Carefully vacuum the Turny. Do not use any liquids.
Contact your installer to book the annual service.
Always contact your dealer for disassembly.
Turny
32
Care instructions

1
2
3
4
5
6
Message Cause Actions
No diode lit The vehicle's engine is switched on and/
or the door is closed. Power supply
interrupted.
Switch o ignition and check that
fuse(s) and cable(s) are intact. For
further help contact your installer.
1 Red blink Power surge or pinch protection. Turny
stops with small amount of reverse
movement.
Check for obstacle(s) in the way.
Reactive Turny.
2 Red blinks Potentiometer broken or disconnected. Contact your installation engineer.
3 Red blinks Potentiometer/lift motor not moving. Contact your installation engineer.
4 Red blinks Faulty switch for inwards- or outwards-
rotated position. Both aected
simultaneously.
Contact your installation engineer.
5 Red blinks Upper limit position broken, constant
fault.
Contact your installation engineer.
6 Red blinks Max limit for manoeuvring has been
reached, 180 seconds.
Contact your installation engineer.
Alternating Red and Green
LEDs
Upper limit position not aected, and max
outwards-rotation not aected. Turny
cannot be manoeuvred.
Contact your installation engineer.
Hand control error messages
33
EN
Turny
Troubleshooting
Troubleshooting

Length .....................................................................................................590 mm
Width.......................................................................................................475 mm
Installation height, up to chair attachment..........................165 mm
Maximum user weight........................................................................150 kg
Voltage......................................................................................................12 VDC
Fuse....................................................................................................................30 A
Power consumption at maximum load.........................................18 A
Power consumption in standby mode....................approx. 15 mA
A / Rotation angle
HD.........................................................................................................78° - 105°
Orbit.......................................................................................................68° - 97°
B / Vertical movement
HD/Orbit 300 .....................................................................................300 mm
HD/Orbit 480 .....................................................................................480 mm
The length and width dimen-
sions show Turny without
covers or accessories.
A
B
From the back, rotated out to-
wards the right.
From above, rotated out towards the right.
590 mm
165 mm
475 mm
Turny
34
Technical specification

35
EN
Turny
Introduction for users
Introduction for users
Date /
Name of dealer /
Signature, installation engineer Signature, user
BraunAbility Europe AB would like you, as a user, to feel secure and comfortable with
your new product. For that reason, it is your installer’s duty to go through the following
with you /
Safety
Operation
Emergency-mode operation
If any questions about the product should come up later on, you are of course very
welcome to contact your installation engineer again.
The above chapters have been gone through /