Brickcom Mini Dome Series User manual

1
Table of Contents
English ...................................................................................................................3
Deutsch................................................................................................................15
Español................................................................................................................27
Français ...............................................................................................................39
Italiano .................................................................................................................51
Português ............................................................................................................63
Русский ...............................................................................................................75
日本語 ..................................................................................................................87

2
Mini Dome Series Model Number
MD-100A
MD-100Ap-00
MD-100Ae-00

3
English
Megapixel Mini Dome
Network Camera
MD-100A Series
Easy Installation Guide

4
1. Check Package Contents
a. Network Camera (MD-100A) b. Product CD
c. Water-Proof Connector d. Allen Key
e. Warranty Card f. Screw bag
g. Easy Installation Guide h. Alignment Sticker
i. Dry Bag / Double-Sided Tape

5
2. Device Description
< Inner Panel >
< Outer view >
NOTE - (*) These are optional features. Please refer to the Product List
for the full list of optional features that are available for this product.
LED Indicators
Screw Hole
Reset Button
Micro SD/SDHC Card Slot (*)
Microphone Hole (*)
Security Screws
Lens Hood
Screw Hole
Lens
Screw Hole

6
3. Hardware Installation
WARNING - Do not mount the camera on a soft material. The camera
may fall and be damaged.
This document is for easy installation purpose only; please refer to
the user manual for more details.
1) Use the enclosed Allen key to detach the dome cover from the camera
device.
2) Remove the dry bag from its package. Use the double-sided tape to stick
the dry bag onto the designate position inside of the dome cover.
3) Choose the location on the wall or ceiling to place the camera. Attach the
location sticker to the desired spot. For ceiling installation, the best place to
mount the camera is into a ceiling stud.
4) Drill three holes through the center of the three location holes on the sticker.

7
5) Hammer the three plastic anchors provided in the product package into the
three location holes.
6) The user needs the three screws which are included in the product package
and a screwdriver. Mount the camera on the wall or ceiling and position
the three screw slots over the plastic anchors. Insert the three screws
provided in the product package into the holes and use a screwdriver to
tighten the screws clockwise until they are secure.
NOTE - For assembling the waterproof connector, please refer to the
instructions included in the connector package.

8
4. Camera Connection
1) Connect the camera to a PoE-enabled hub via a single Ethernet.
2) Connect the camera to a non-PoE hub using a PoE Injector.

9
5. Lens Adjustment
I. Adjust the lens to the desired position.
II. Focus
1) Loosen the lens lock screw.
2) Remove the lens hood.
3) Rotate the lens until the image in the Live View page is focused.
4) Retighten the lens screw lock.
5) Reattach the lens hood.
WARNING - Do not over rotate the lens.
6. Complete the Installation
Place the dome cover back on the camera device using the supplied Allen Key.
Lens Lock Screw

10
7. Setup the Network Camera
Insert the Installation CD into the CD-ROM driver. Run Auto-Run Tool directly
from the CD-ROM to start the installation. When installing the Brickcom software
kit for the first time, select a desired language for the interface. The available
languages are listed in the scroll box. Click <Install> and follow the steps to
install the EasyConfig wizard on the desired computer.
Please follow the instruction of the InstallShield Wizard to finish the Brickcom
Software Kit installation.
To launch EasyConfig or PC-NVR Standard, select the application and click
<Finish>. When launching the PC-NVR program, please refer to the PC-NVR
user manual.

11
7.1 EasyConfig
To launch EasyConfig, select EasyConfig from the start menu. If Complete
Setup type was used in the software installation, an EasyConfig icon was
installed on the desktop. Double click to open the icon.
If Custom Setup type was used in the software installation and an
EasyConfig icon was not installed on the desktop, the program will be
installed under C:\Program Files\Brickcom\EasyConfig unless the program
was saved to a preferred directory.
I. Click <Start> to continue. The program will automatically search for
the camera in the intranet.
NOTE - Check “Skip the hardware installation guide” to skip
checking the hardware connection. To check the hardware
installation settings, do not check the option box.
II. Select either “Simple Mode” or “Professional Mode” to obtain the
camera’s IP settings. If “Simple Mode” is selected, EasyConfig will set
up the connection automatically. If “Professional Mode” is selected, the
user will need to configure the IP settings manually.
III. There may be many cameras in the local network. Differentiate the
cameras using their UPnP name. Double click on the camera from the
survey list to connect.

12
IV. For configuring the IP address settings, select either <Settings remain
the same>, <Automatically obtain an IP Address (DHCP)> or <Set IP
Address configuration manually>. The DHCP setting is recommended.
If <Set IP Address configuration manually> is selected, the following
pages will be displayed.

13
V. If the camera supports the EasyLinkTM function, the following page
will be displayed. Otherwise, this page will not be shown. *If desired,
click <Skip> to skip this setting.
EasyLinkTM is a unique Brickcom function which allows users to assign
a unique EasyLink name to their network camera’s IP address. There
is no need to configure the router to open up ports or remember
hard-to-memorize IP addresses. Users can log onto
[uniqueEasyLinkname].mybrickcom.com to view the camera’s web GUI
and live view.
1) Enter a unique EasyLink name whose length must be between 5-32
characters.
2) When finished, click the arrow button to continue.

14
VI. When the IP address settings have been configured, the screen will
either display a successful or failed connection message. If the
connection failed, either try again or quit the installation.
When this window is displayed, click <PC-NVR> to start the PC-NVR
program, <Live View> to view the live video from the connected IP
camera, or <X> in the top right corner of the screen to close the
installation window. To run the PC-NVR program, please refer to the
PC-NVR user manual for more information.

15
Deutsch
Megapixel-Mini-Dome-
Netzwerkkamera
MD-100A Serie
Schnell-Installationshandbuch

16
1. Überprüfen Sie den Verpackungsinhalt
a. Netzwerkkamera (MD-100A) b. Product CD
c. Anschlusskit für wasserdichten
RJ45-Anschluss
d. Inbusschlüssel
e. Garantiekarte f. Befestigungsschrauben
g. Schnell-Installationshandbuch h. Bohrschablone
i. Trockenbeutel/Doppelseitiges Band

17
2. Kameraskizze
< Innenansicht >
< Außenansicht >
HINWEIS - (*) Optionale Funktionen. Eine vollständige Liste der
optionalen Funktionen, die für das Produkt zur Verfügung stehen, ist
auf der Geräteliste aufgeführt.
LED Leuchten
RESET-Taste
Mikro-SD/SDHC-Karten-Slot (*)
Mikrofon (*)
Sonnenblende
Befestigunsloch
Objektiv
Befestigungsloch
Befestigungsloch
Sicherheitsschrauben

18
3. Hardware-Installation
WARNUNG - Die Kamera nicht auf einer weichen Fläche
montieren, da sie sonst herunterfallen und beschädigt werden
kann.
Dieses Dokument ist nur eine Schnell-Installationsanleitung. Für
mehr Details beziehen Sie sich bitte auf das Benutzerhandbuch.
1) Den Dome-Deckel mit dem mitgelieferten Inbusschlüssel von der Kamera
loslösen.
2) Den Trockenbeutel aus dessen Verpackung nehmen und mit dem
doppelseitigen Band auf die im Dome-Deckel markierte Position kleben.
3) Einen Ort an der Wand oder Decke auswählen, wo die Kamera installiert
werden soll. Die Bohrschablone auf die gewünschte Stelle kleben. Für die
Installation an der Decke ist ein Deckenpfosten der beste Ort zum
Installieren der Kamera.
4) Mithilfe der Bohrschablone die Löcher an die Wand oder Decke bohren.

19
5) Die drei mitgelieferten Plastikdübel mit einem Hammer in die drei
Arretierlöcher einschlagen.
6) Zum Installieren werden die drei Schrauben, die in der Verpackung
mitgeliefert sind, und ein Schraubenzieher benötigt. Die Kamera an der
Wand oder Decke installieren und die drei Schraubenschlitze über die
Plastikdübel positionieren. Die Schrauben in die Löcher einsetzen und mit
dem Schraubenzieher in Uhrzeigerrichtung festziehen, bis diese sicher
befestigt sind.
HINWEIS - Die Anleitung für die Montage des wasserfesten RJ45
Anschlusses sind in der Verpackung des Anschluss-Kits.

20
4. Kamera-Anschluss (2. Optionen)
1) Die Kamera mit einem Netzwerkkabel an einen PoE-fähigen Switch
anschließen.
2) Die Kamera mit einem PoE-Injektor an einen nicht-PoE fähigen Switch
anschließen.