Bristan GLD2 BSM C Wiring diagram

Installation Instructions
& User Guide
Please leave these instructions
with the end user
Pack Contents
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your
product.
Specifications
Dynamic Water Pressure
Maximum Static Pressure: 10.0 bar
Min: 0.2 bar Max: 5.0 bar
All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and
receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water
Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014.
For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.co.uk/approvals-directory
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance.
Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc.
Full access must be made available for future maintenance/servicing purposes.
This product must not be modified in any way as this will invalidate the guarantee.
Adjustable Spanner Hexagonal Keys Philips Head
Screwdriver
Box Spanner
(Cartridge)
Box Spanner
(Inlets)
0
1.0
2.0
5.0
4.0
3.0
Pressure
BAR
Inlet Water Temperature Inlet Connections
Spare Parts
Prior to Installation
Tools Required for Installation/ Maintenance
Operation
3/4” BSP
PencilSafety GlassesDrill
2.5mm
31mm 17mm
Size 1
ø6mm
60°C
Maximum Hot 60°C
GLD2 BSM C (D1)
Pack Contents
Tools Required for Installation/ Maintenance
x1
Handset
Operation
Plinth
Plinth Seal
Rubber Washer
Backnut
Glide 2 Tap Hose
x1
x2
x2
x1
Bracket
x1
Pull up
diverter for
Handset
Push diverter down
for Bath Fill
Hot
Cold
On
On
Elbow
Connection
x1

Installation
1*
1
Connect the hot and
cold water supplies to
the threaded tails
Hot
Cold
REMEMBER
Hot on the
left, cold on
the right!
3
Important
The images shown are for
illustrative purposes only.
The tap you have purchased may
look dierent to those pictured in
this booklet but will follow the same
installation steps.
Your contents page will be specific
to your product.
If you find your product or any of
its components dier from those
shown on the contents page, please
contact our customer support.
Secure the
nut end of the
hose to the
threaded outlet
connection*
If your model
has one, ensure
the loose washer
is lying flat inside
of the nut
4
Feed the tap body through
the plinths and ensure
rubber plinth seals are
in place
Once aligned, feed the
threaded tails through
tap holes
Your model may come
with a plinth and will
either be included
pre-attached or loose in
the box*
You may be required to
secure the plinth to the
tap with a grub screw
If the hole is not
directly visible on the
plinth, check underneath
rubber seal
Ensure rubber seal is in
place once plinth is
attached
2
To secure the taps to the bath, use a box spanner
to tighten the metal backnuts underneath
ensuring the washer is correctly positioned in
between the backnuts and the bath

Installation - Wall Bracket
5Secure the cone end
of the hose onto the
threaded inlet connection
of the handset
If your model has one,
ensure the loose washer
is lying flat inside of the
cone connection
IMPORTANT
Turn on water
supply for a few
minutes and
check all joints
and connections
for any leaks.
Your tap is now
ready to use
12
Observe screw
holes inside of
the bracket
Drill hole(s) and fit wall
plug(s) and then secure
wall bracket to wall using
screw(s) provided
4
IMPORTANT
Prior to drilling
into walls, check
there are
no hidden electrical
wires, cables or
water supply
pipes
Check handset sits
securely
on the wall bracket and
there is no movement
*Some models
will require you to
unscrew the hook
to gain access to
screw hole(s)
Once fixed, replace the
bracket lid
3
Pry o the bracket
lid to reveal the
screw holes (this will
be opposite the wall
end of the bracket)
Position the wall
bracket where you
want it and mark out
where to drill. Make
sure the hose and
handset can reach
(On most models,
the screw holes are
large enough to fit a
pencil through for easy
marking)
Your bracket is
now ready to use
4* If your model is supplied
with an elbow connection,
ensure it is attached first
before connecting the hose
Then attach the hose to
the connection on the
opposite end of the elbow
To attach elbow,
screw it tightly
to the threaded
connection on
the tap body

Reverse the steps to replace
the cartridges/ valves and
handles
123
2* 3
1
Unscrew the
cartridge/ valve
using a box
spanner
Remove indice by
pulling it loose, then
undo hex grub screw
to remove handle
(When replacing,
ensure valve is fully
closed with the handle
parallel to the spout)
Love Your Chrome
Bristan oers an eective
chrome-friendly cleaning kit
for use with your taps and
showers. Scan the QR Code or
search for ‘CLEAN KIT01’ on
www.bristan.com.
Indice will be placed
on either the front or
back of the handle
IMPORTANT
Isolate the
water supply
before
starting!
Remove the screw and
spline adapter if your
model has them and gain
access to the cartridge*
Check any seals
and O-rings
for damage.
Replace
cartridge/ valve
if necessary
Maintenance - Cartridge/ Valve Replacement
2
If your model has a
shroud, it will need to be
removed to access the
cartridge
To remove the
shroud, twist
to unscrew
then lift o of
the tap body
The top of the
cartridge will now be
fully exposed ready
for removal
4Bristan products are made from premium
materials, with hand polished, electroplated,
PVD or EPD finishes.
Your taps or shower should be regularly
cleaned with warm water, a mild pH-neutral
liquid soap, and polished with a soft cloth.
Any residues from soap, toothpaste,
shampoos and shower gels can cause
blemishes if not rinsed o straight after use.
Household bleaches and cleaners contain
harsh chemicals and may damage the surface
finish. Avoid using abrasive cloths, scouring
pads, scrub sponges, steel wool or anything
similar.
General Cleaning

Symptom Cause Remedy
Low Flow
Partially closed isolation valve. Open isolation valve.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of
debris and any airlocks.
Partial blockage in the outlet Remove to Clean and soak in suitable
solution.
No hot water or
cycling hot and
cold
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or pressure through
system.
No Flow Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Temperatures not
corresponding
with taps
Inlet pipes have been connected
incorrectly
Swap the inlet tails around.
Troubleshooting
Notes
Please use this space for any notes you
or your installer may have regarding the
installation/plumbing of this product.
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer
solid guarantees on all our products, eective from the date of purchase, to give you peace of mind.
Your guarantee starts from the purchase of your product, but you can still benefit from registering it for
easier identification in the unlikely event of a manufacturing fault, please visit www.bristan.com/register
For any other queries, please call Customer Service on 0330 026 6273 where our expert team
of advisors will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service-centre/guarantees.
Our Guarantee
Bristan Group Ltd.
UK: Bristan Group, B78 1SG.
EU: Masco Europe S.à.r.l.
14 Rue Strachen
6933 Mensdorf
Luxembourg
Customer Service: [phone]
Web: www.bristan.com
Email: [e-mail]
A Masco Company
Contact Us
Servicing Your Tap
We recommend servicing your tap at
least once every year to prolong its life.
To see a video showing how to remove
the cartridge for servicing, scan the QR
code with your smart phone or tablet.
Alternatively visit www.youtube.com/
BristanTV