Bristan EV KIT-EFB C Mounting instructions

Installation Instructions
and User Guide
Evo Riser Rails and Kits
Models Covered:
EV KIT-EFB C, EV KIT-EEFB C H,
EV KIT-EEFB C, EV KIT-EEVK C
Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave
them with the user.

Contents
• Important Safety Information 3
• Dimensions (mm) 4-5
• Pack Contents 6
• Installation 7-9
• Operation 9
• Maintenance 10
• Troubleshooting 11
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Contents
2
Thank you for choosing Bristan, the UK’s leading taps and
showers expert. We have designed these products with your
enjoyment in mind.
To ensure that they work to their full potential, they need to be
fitted correctly. These fitting instructions have been created to
give you all of the information you need and, if you need any
further help, please do not hesitate to give us a call on 0300 026
6273.

Please read these instructions thoroughly and retain for future use.
All products manufactured and supplied by Bristan are safe provided they
are installed, used correctly and receive regular maintenance in accordance
with these instructions.
If you are in any doubt about your ability to install this product safely you
must employ the services of an experienced qualified plumber.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and
current byelaws. For full Installation Requirements & Notes (IRN) please visit
wras.co.uk/directory.
Before starting any installation please consider the following:
Before drilling into walls, check that there are no hidden electrical
wires, cables or water supply pipes. This can be checked with the aid
of an electronic detector.
If power tools are used do not forget to: - Wear eye protection
- Unplug equipment after use
• Remove all packaging and check the components for damage.
• Do not use if the shower head or hose has been damaged or blocked.
• Do not block the flow of water from the shower head, by placing it
(smothering it) on your hand or any other part of your body or
foreign object.
• Do not crush or kink the shower hose, this could damage the hose and
cause leaks.
• This product must not be modified in any way as this will
invalidate the guarantee.
If in doubt, contact a registered plumber or your Local Water
Authority or the Secretary of the Institute of Plumbing,
address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]
Recommended Usage
Domestic Heavy
Commercial
Light
Commercial
Healthcare
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 3
Important Safety Information

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Dimensions (mm)
EV KIT -EFB C EV KIT -EEFB C
4

EV KIT -EEFB C H EV KIT -EEVK C
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 5
Dimensions (mm)

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Pack Contents
1
2
1
2
3
4
5
6
1. Wall Brackets x2
2. Riser Rail x1
3. Slider x1
4. Handset x1
5. Fixings x4
6. Hose x1
7. Shelf *not shown x1
6

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 7
Installation
1. Mark the position
Position the assembled riser rail
onto the wall, bearing in mind
the highest maximum position
required for the handset. With the
riser rail vertical, mark the position
of the wall brackets onto the wall
surface.
2. Attach wall bracket fixings
Remove the wall brackets from
the rail and then remove the
fixings from the wall brackets.
Position the fixing bracket in the
marked positions against the wall,
ensure they are vertically in line
with each other and mark the
centres of the fixing holes onto
the wall.
Warning: Please check
for any hidden pipes and
cables before drilling holes
in the wall.
Drill suitable holes and insert the
wall plugs. Securely attach the
fixing brackets to the wall using
the screws.
Tip: A piece of
insulation or
masking tape
positioned where
holes are to be
drilled and before
marking out the
exact position for
the fixing holes will
help stop the drill
bit from wandering,
particularly on a
tiled surface.
When working near
a basin, bath or
shower insert plug
or cover waste
to prevent losing
small parts. Take
care not to drop
tools / equipment
into basin, bath
or shower during
installation.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Installation
3. Insert riser rail
Ensure the rail clamps are in position
and push the riser rail up through
the bottom wall bracket.
Push the shelf and slider down onto
the riser. Ensure the slider it is the
correct way up, as shown opposite.
Push the riser rail up through the
top wall bracket.
4. Tighten rail clamps
Centre the riser rail within the wall
brackets and tighten both clamps
located inside the wall bracket onto
the rail.
5. Fit the riser to the wall
Slide the riser brackets over the
bracket fixings attached to the wall.
Tighten the grub screw on
the underside of both top and
bottom wall brackets using a
2.5mm hexagonal key.
Rail
Clamps
Component Order
Bottom Bracket
Shelf then Slider
Top Bracket
Fit to Wall
8

6. Connect shower hose
Screw the shower hose (ribbed
end) onto the shower valve outlet
(not supplied), ensuring the rubber
washer is fitted.
7. Connect shower hose to
shower head
Screw the shower hose (conical
end) onto the shower head ensuring
that the rubber washer is fitted.
Place the shower head into the
slider.
Adjusting the Slider
Press the button on the underside
of the slider to move higher or
lower for user height.
To adjust the angle of the shower
head, twist the slider bracket to
the desired position.
EEVK Multi-Function Handset
Jet Combination Spray
Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 9
Installation
Operation
The multi-function shower head has 3 spray functions, spray, jet and
combination. Simply rotate the spray head one way or the other to the
desired spray pattern.
Push to
Adjust
Height
Twist

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
Maintenance
10
General Cleaning
Bristan products are made from premium materials,
with hand polishing and electroplated finishes.
Your product should be regularly cleaned with warm
water, a mild pH-neutral liquid soap, and polished
with a soft cloth. Any residues from soap, toothpaste,
shampoos and shower gels can cause blemishes if
not rinsed o straight after use.
Household bleaches and cleaners contain harsh
chemicals and may damage the surface finish.
Avoid using abrasive cloths, scouring pads, scrub
sponges, steel wool or anything similar.
Some surfaces such as nickel and pewter may be
aected by the dye found in some cloths, so it is
also important to avoid hanging cloths on spouts.
Your Bristan shower head has rub-clean nozzles for
easy cleaning. Simply rub your fingers across the
rubber spray jets regularly and before you turn the
shower on to remove any scale or debris.
Cleaning the Shower Head
The hardness of the water in your area will determine
how often you should clean your shower head.
Build up of scale in particularly hard water areas
combined with constant use means you may need to
clean your shower head once a week. To ensure
continued performance the shower head needs to
be regularly de-scaled.