Bristan Java Eco Click J EBAS C User manual

AFTERCARE INSTRUCTIONS
Your fitting has a high quality finish and should be treated with care to preserve the
visible surfaces. All surface finishes will wear if not cleaned correctly, the only safe
way to clean your mixer is to wipe with a soft damp cloth. Stains can be removed
using washing up liquid. All bath cleaning powders and liquids will damage the
surface of your fitting even the non-scratchcleaners.
GUARANTEE
All products are manufactured to the highest standards and a 5 year guarantee
covers any defect in manufacture.
NOTE: The 5 year guarantee on the valve is invalidated if damaged by any
waterborne debris.
In the interests of continuous product development we reserve the right to alter
specification as necessary.
PRODUCT CODE: J EBAS C
TELEPHONE HELP LINE:01827 311345
Bristan Group Ltd
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
UK
A Masco company
Web Site: www.bristan.com
Telephone: [phone]
Facsimile: 0808 1611002
Email: [email protected]
(FI JEBAS) (Rev. D1) (MZ)
Java Eco Click
Basin Mixer
Fitting Instructions
& Contents List
Please keep these instructions for future reference
and for the ordering of spare parts.
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk

6
5
4
3
2
1
8
9
710 12
11
13
15
d
e
f
c
ba
14
WATERPRESSURE
Thismixerissuitableforuseatallsupplypressures.Howeverforoptimumuseboth
the hot and cold supplies should be reasonably balanced. If the fitting is installed at
low pressure (tank fed), then the minimum distance from the outlet of the nozzle to
the underside of the cold tank should be approximately 2.0 metres to ensure
adequate performance.
This mixer should be installed in compliance with Water Regulations. Where the
supplies are unbalanced, i.e. hot water from the cylinder tank/cold from the mains,
approvedcheckvalves must be fitted in the supply pipes. Forfurther detailscontact
your Local Water Authority.
PleaseNote:
In the unlikely event you find a part missing please contact our customer service
helpline on 08704425553 for immediatedispatch of part.
INSTALLATION
1. Identifyall components andcheck forcompleteness, particularly beforearranging
fitting.
2.Fit the mixer body (1) to the basin/bidet using the 'C' plate fixing kit. The plinth (3)
and ‘O’ ring (15) go between the fitting and the basin/bidet, and the 'C' shaped
rubber (4) and metal washers (5) on the underside of the basin/bidet. Secure into
position using threaded rods (8) and nuts (6).
3.Fit the inlet connection tailpipes (7) to the fitting and connect the hot and cold
supplies.
4.Fit the pop up waste, using washers (11) below & (12) above the basin/bidet and
connect it to the mixer. It is recommended that a silicon sealant be applied to both
sealing faces of washers (11) and (12)The waste can be set by adjusting the waste
rod (9) / operating rod (2) connecting bracket and the screw in the base of the plug
(14).
5.Fully open the mixer in the mid position, letting it run for a few minutes to check
all joints and connections for leaks.
6. See over the page foraftercare instructions.
ECO CLICK An innovative water saving feature that offers a subtle
resistance as it reaches approximately half of its full flow
capability. For increased flow this feature can be overridden.
At full flow the eco click cartridge uses 32% less water than a
standard cartridge and when in eco click mode the reduction
increases to 72%.
MAINTENANCE
If the fitting begins to drip:
1.Turn off the water supply.
2.Remove indicecap (a), loosen grub screw (b)with ahexagon key and pull off
head (c), unscrew shroud (d) retaining nut (e).
3.Remove cartridge (f).
4.Clean or replace cartridge, clean and grease seal and refit. Note:Thereare
locating pins on the bottom of the cartridge that fit in holes inside the tap, to ensure
it is fitted the right way round.
5.Replace cartridge and head and turn on the water supply.
6.Contact our helpline if problem persists.
CONTENTS
1. Mixer body (X1)
2. Pop-up operating rod (X1)
3. Plinth (X1)
4. C-shaped rubber washer (X1)
5. C-shaped metal washer (X1)
6. Nut (x2)
7. Tailpipe (x2)
8. Threaded rod (x2)
9. Waste rod (X1)
10. Waste body (X1)
11. Washer (X1)
12. Washer (X1)
13. Waste flange (X1)
14. Plug (X1)
15. O-ring (X1)
For latest prices and delivery to your door visit MyTub Ltd 0845 303 8383 www.mytub.co.uk