BRONZE GYM D-002A User manual

D SERIES -002A USE MANUAL
SEATED STRAIGHTARM CLIP CHEST

1
CONTENT
IMPORTANT DECLARATION………………………………………..1
WARNING………………………………………………………………..2
USE INSTRUCTION……………………………………………………..3
REGULAR MAINTENANCE…………………………………………....4
CABLE ROUTING DIAGRAM…………………………………………..5
EXPLODED PICTURE…………………………………………………...6
ASSMBLE STEP…………………………………………………………..7
IMPORTANT DECLARATION:
First we are highly appreciated that you buy D-002A SEATED
STRAIGHTARM CLIPCHEST.
For your health and safe, before you exercise please consult from your
doctor and define a appreciated exercise burden for yourself. Before using this
equipment read carefully all related instructions and notice. In this way you gain
more happiness during exercise. When you begin to use D-002A SEATED
STRAIGHT ARM CLIP CHEST , our company think you have read use manual
already. After you buy this equipment, please fill carefully ‘post-sale service
warranty card’ and keep it, meanwhile, post return receipt (stub) back to our
company so that we provide better service for you.
This manual is the first edition 2011 of series products D-002A SEATED
STRAIGHT ARM CLIP CHEST The content of manual will change along with
promotion of products, and we will not inform you.
All notice and instruction are in order to keep yoafe and use this
equipment correctly. If not obeying the suggestion, take the consequence yourself.
After reading, the user must keep this manual in the place you can see it at
anytime.
PRODUCTS INTRODUCTION:
1 The main frame adopts the high-quality steel tube of for use, durable and safe.
2 Adopt high strength steel cable as transmitting wire and you will feel safe and
durable.
3 The weight stack adopts casting iron and has protective cover.
4Rotating part adopts the high-quality bearing, durable in use and there is no
noise while using.
5The high quality leader makes it smoother while using.

2
WARNING
1. This training equipment is only intended for use in training areasof organizations
such as sport associations, educational establishment, hotels, clubs and studios,
where access and control is specifically regulated by the owner (person who has the
legal responsibility).
2. The training equipment shall only be used in areas where access control is specifically
regulated by the owner; the extent of control depends on the users,
e.g. degree of reliability, age, experience, etc.
3. The training equipment shall only be used in supervised areas.
4. Always keep unsupervised children and disabled away from the equipment.
5. Injury to health may result from incorrect or excessive training, please consult the
couch to choice correct exercise method and proper burden.
6. Please adjust the load and equipment further (e.g. seat adjustment) before using.
7. Please check if the bolt and handrail are out of work before you start to use it.
8. When weight stacks, booms and other parts of this equipment are blocked, must
handle with other people’s assistance, in case that the weight stacks may suddenly
drop and cause accident.
9 .Adjust the length of the steel cable properly and never make the steel wire rope
twist. After using the machine for a period, the owner shall check the steel cable to
make sure no unusual phenomena in connecting. When meet any problems, please
consult the professional maintenance personal at once.
10. Do not suddenly drop the weight stack. In order to avoid destroying other weight
stacks, please raise it when the weight stacks nearly collide.
11. While using, forbid hands stretching into the weight stacks or the relative motion
parts, so as not to injure the finger.
12. Never allow person with heart disease and children under 12 to use this
equipment.
13.The training equipment is in compliance with EN 957-2 class S(S=studio);
14.The max training weight is 150kgs (330pound). The max user’s body weight is
150kg (330pound).
15.The machine should be located stably. A space of 2000mm*2000mm should be
around the machine。
16.The scope of products: Primary use in professional fitness club.The second is the
residence community，gym of some company
17. If you feel swirl, surfeit and other discomfort sense, Please stop exercising and go
for doctor.
18. The equipment should be installed on stable even surface.
19. The machine shall only be used indoor and be avoid of moisture.
20. Wear right shoes and coat
21. Warm up before exercising
22. Don’t use the equipment to do the impossible function
23. Please exercise under instruction by professional coach.
24. Inspect if the equipment is fastness before using
25. Any of the adjustment devices that could interfere with the user movement
should not be left projecting.

3
USE INSTRUCTION:
D-002ASEATED STRAIGHTARM CLIP CHEST
Exercise position: Pectorals
Dimension: 2000mm (L)*1110mm(W)*1000 mm(H) weight : 185kg
Use Instruction:
1Read all caution Warning Labels before using this equipment.
2Adjust seat pad and sit with your back firmly against back pad.
3Insert pin into weight stack at desired resistance level.
4Hold the lever firmly, securely position both hands in an overhand grip or with
palms facing each other.
5Keeping your arms close to your sides, slowly push forward while maintaining a
smooth, comfortable exercise movement.
6Parse for a moment, then slowly return to the start position and repeat the
movement.
NOTICE:
1.Warm-up…..It needs warm-up for 5-10 minutes before starting exercise, for
instance mark time, free-standing exercises etc., in order to move each
joint muscle, so as not to injure the joint muscle while exercising.
2 Diet ………Eat some more protein, vegetables, and fruit. Begin to do exercises until
40 minutes after a meal. Taking food until half an hour after doing
exercises and drink little water while doing exercise.
3.Breath….….Breathe in while exerting oneself, exhale while relaxing. To coordinate
breathe with movement.
4 Frequency…It needs to take a rest over 48 hours before exercising the same muscle.
5 Burden…….Exerciser should choose suitable weight according to one's own actual
conditions, make sure not to be overweight, so as not to cause the
muscle to draw wounded. Exercises should according to the
progressive principle; it is normal to feel ache while exercise for the
first time.

4
REGULAR MAINTENANCE
1．The safety level of the equipment can be maintained only if it is examined
regularly for damage and wear, e.g. ropes, pulleys, connection points;
2．Pay special attention to components most susceptible to wear.
3．Replace defective components immediately and /or keep t he equipment out
of use until repair;
4．This equipment should carry on regular maintenance according to the
following chart:
INSTALL SKETCH MAP
Let assembly become easier
All the content of user’s manual is to assured the strength training machine can be
installed more easily
Reading the details and instructions before installing:
1．Because the size and weight of equipment is so large, Please choose the installed
place near the desired station and assured there is enough space to exercise
2．All parts can be put on the clear area, then backout the wrapper. And the wrapper
can’t be through away before installation finished.
3．Screw the bolt tightly except the additional instruction
4．All parts must be installed according the illustration indication.
5．Installation work can be finished by tow men
6．Identify all parts by part identify chart
MAINTENANCE
EVERYDAY
EVERY WEEK
THREE MONTHS
Check: connecting, bolt,
Weight stack bolt
√
Clearance:
cushion and cover
√
Lubrication:
place of sliding
√
Check:
bolt if tighten
√
Lubrication:
Bracket of bearing
√

5
CABLE ROUTING DIAGRAM：

6
4-B18
B25
2-H08 AB1
2-H07
2-H06
H10
H11
2-H05
AL1
15-H02
H01
B15
B35
B15
B16
B17
2-C35
B12 B14
2*C18
2*B12
2*C36
2*B16
B26
2*B16 2*B20
2*B16
2*B16
2*B20
4-B22
4-B23
4-B24
B21
AE2 C35
G06
G07
G06
4-C28
4-C27
AG1
2*B16
2*B19
C32
AC1
G03
C39
C39
B13
B12
B11
B12 B14
2-D35
2-D22
2-D40 AD4
AD5
2-D35
B14
B12
AD2
2-D22
2-D40
D32
AD3
D29
C26 D25
D31
D23
D24
D27
D17
D18 D19
D21
D32
AD3
D29
C26
D25
D31
D23
D24
B12
D30
D48
D48
2-D50
D51
D30
2-B12
AD1
D512-D50
B14
D27
2-C17
2-C28
2-C27
2-B16
2-B19
D49
D49
H12
G26
4-C28
4-C27
B14
B13
2-B12
B11
B13
2-B12
B11
B14
B13
B11
2-B12
B14
2*B29
D17
D18
D19
D21
F11
F11
4*B37
2*B20
2*B16
2*C26
2*G05
2*D29
4*C22 AC2
AE1
AC3
B13
B12
B11
3*C86
Z01 Z02
C43
C43
2*H07
2*H08
4*B37
G73
B13
B14
2-B12
B11
G74
H36
H36
Exploded Picture

7
Assmble Step：
Use tool：
1. M5 Hex spanner
2. M6 Hex spanner
3. Two 13-16 spanner
4. Two 17-19 spanner
5. Two 22-24 spanner

8
Step1
2*B16
2*B20
2*B16
2*B16
2*B19
C32
B26 junction plate 160L*56.1W*4t 1 B29 outer hexagon screw M12*130L 2 B19 outer hexagon screw M12*80L 2 C32 junction plate 160L*50W*4t 1
C36 pulley sleeve M12*30L 2 C18 outer hexagon screw M10*30L 2
B12 gasket M10*2t 4
B14 lock nut M10 2
AB1
3*C35
2*B12
2*B14
2*C18
2*B12
2*C36
2*B16
B26
2*B16
2*B20
AE2
AC1
2*B29
AE1
AB1 wicket welding group 1 AC1 big frame welding group 1 AE1 upper connection support 1
AE2 below connection
bending support 1
C35 feet pad 136L*76W*3t 3 B20 lock nut M12 4 B16 gasket M12*2t 10
No. Name Spe Quantity

9
No. Name Spe Quantity
Step2
2*B16
2*B16
2*B20
2*B19
AC2
B16 gasket M12*2t 4 B19 outer hexagon screw M12*80L 2 B20 lock nut M12 2
AC2 longitudinal framework tube 1

10
AD3 arm assembly 2
C26 semicircle head inner
hexagon screw M8*15L 2
D29 bearing cap M53 2
AD1 left forearm assembly 1
AD2 right forearm assembly 1
No. Name Spe Quantity
Step3
AD2
2*AD3
2*D29
2*C26
AD1

11
No. Name Spe Quantity
Step4
4*C28
4*C27
AG1
G03
4-C28
4-C27
G26
AG1 seat tube bonding 1
G03 upholstery 1 G26 back cushion 1 C27 semicircle head inner
hexagon screw M8*25L 8
C28 gasket M8*2t 8

12
center rod welding group
No. Name Spe Quantity
Step5
2*H08
2*H06
AL1
15*H02
2*H01
H12
4*B37
weight stack
AL1 1
H02 340L*100W*26t 15
H06 guide bar ∮20*1450L 2 H08 guide bar head shaft for
inside plug ∮34*20L 2
H12 broaching of weight stack 1
H01 guide bar cushion ∮55*60L 2
B37 clamp spring ∮30*∮18*1.5t 4

13
B27 semicircle head inner
hexagon screw M8*20L 2
D49 cable loop ∮20*30L 2
H10 M16*60 1
H11 M16 1
AC3 1
No. Name Spe Quantity
bolt of cable locker
nut
wheel box welding group
Step6
AC3
H11
H10
D49
H36
D49
H36
cable

14
No. Name Spe Quantity
Step7
B23 broaching sleeve 4
B24 broaching screw 4
∮25*20L
∮30*M8*56L
4*B18
B25
4*B23
4*B24
B21
B21 door guard board 1
B25 door guard board 1 B18 inner hexagon screw M8*20L 4