Bticino Living Now with Netatmo User manual

Installation Manual
www.bticino.com
Living Now with Netatmo

Living Now with Netatmo
Installation Manual

3
Contents
Living Now with Netatmo
Installation Manual
General features 4
Install Living Now with Netatmo 5
Associate the connected devices 9
Add a connected device 15
Add a wireless scenario control 17
Associate a wireless light/rolling shutter control to one or more modular
connected devices 20
Dissociate a wireless control from the connected devices 26
Reset to the factory settings 26
Use the App 28

4
Living Now with Netatmo
Installation Manual
General features
The Gateway allows you to create your Smart electric system by associating together all the
connected devices of the Living Light with Netamo range and light relays.
Supplied as standard is also the wireless master IN&OUT scenario control, item L/N/NT4570CW,
required for the association of all the connected devices and for the activation of the “IN” and
“OUT” scenarios.
The Gateway connects to your home router through the Wi-Fi connection (2.4GHz only), to allow
the local or remote control of lights, controlled sockets and rolling shutters using the smartphone
(“Home + Control” App) or voice commands (using a voice assistant).
In order to optimize signal reception, it is recommended that the Gateway is installed close to the
router.
Note: not all the products shown in this manual are available for all markets.
Check the availability of the same from your supplier or installer.
Gateway
K4500C KG/KW/KM4501C KG/KW/KM4502C
Connected
socket
K4531C KG/KW/KM4141C KG/KW/KM4142C
Connected
light switch/
light relay
ZLD15
K4411CM2
RF
L
NN
µ
1.3A max
0.4A max
ON
OFF
100-240V
50Hz/60Hz
Made in
China
ZLS26
K4003C K4411CM2 3584C
Shutters
ZLSH06
K4027CM2
K4027C K4027CM2
Radio controls K4003CW K4003DCW K4570CW
1 2
K4027CW 3577C K4574CW

54
Living Now with Netatmo
Installation Manual
Install Living Now with Netatmo
Check that the system is not powered.
It is now possible to connect all your system devices as per the following diagrams.
OFF
1. Disconnect the voltage from the general switch.
1

6
Living Now with Netatmo
Installation Manual
L
N
L
Connected
two-way switch
K4003C
1C
2
L1
L2
2
1
Measurement
toroid
Connected DIN
meter
F20T60A
L
N
Traditional
intermediate
switch
RF
L
NN
µ
1.3A max
0.4A max
ON
OFF
100-240V
50Hz/60Hz
Made in
China
ZLS26
L
1
N
Connected shutter
control
K4027C
N
Connected
module for socket
K4531C
Connected 2-module
shutter control
K4027CM2
AS AN ALTERNATIVE
Connected
dimmer
K4411CM2
* provided with
K4411CM2
Compensator *
Gateway
KG/KW/KM4502C
Gateway
KG/KW/KM4501C
Connected
two-way switch
K4003C
Traditional
two-way
switch
Gateway
K4500C
Wireless In&Out
master scenario
control K4570CW
Wireless In&Out
master scenario
control K4570CW
Wireless In&Out
master scenario
control K4570CW
Connected
light relay
3584C
Traditional
pushbutton
Traditional
socket
Connected socket
KG/KW/KM4141C
Connected socket
KG/KW/KM4142C

76
Living Now with Netatmo
Installation Manual
1 2
Check that the LEDs of all the devices turn on red steady (with the exception of the wireless LEDs,
which will be off ).
ON
2. Reconnect the power using the general switch.
2

8
Living Now with Netatmo
Installation Manual
It is now possible to associate all the devices and take advantage of the connected functions of
your system.
Note: connected sockets will be powered by default.
After installing the Smart electric system, it will be possible to locally control lights and rolling
shutters without further set up needed.

98
Living Now with Netatmo
Installation Manual
1 2
Associate the connected devices
Wait 1 minute for correct system start-up, after which complete the following association
procedure within 15 minutes from powering.
If this time is exceeded, disconnect and then reconnect the power.
ON

10
Living Now with Netatmo
Installation Manual
1. Remove the tab from the wireless control (K4570CW Master) in K4500C – KG/KW/KM4501C –
KG/KW/KM4502C.
3. Press and release one of the control keys: the LED flashes green; release it and wait for the LED
to turn off.
Note: after re-powering the system always wait at least one minute.
K4570CW Master, wireless In&Out scenario control
1
2
2. Fit the cover and the plate on the wireless control.
Warning: if cover and plate are not fitted, do not press the wireless control keys.
3

1110
Living Now with Netatmo
Installation Manual
4. Start the association:
press and hold down the two control keys at the same time, the LED will turn green, the LED
switches off.
K4570CW Master, wireless In&Out scenario control
K4500C Gateway
The Gateway LED goes from red to off.
KG/KW/KM4501C Gateway KG/KW/KM4502C Gateway
4
4

12
Living Now with Netatmo
Installation Manual
1 2
Note: the LEDs may take up to 15 minutes to turn from red to green.
After this time, the procedure will end automatically.
Check that the LEDs of all the devices turn green steady (with the exception of the wireless LEDs,
which will be off ).
5. End the association:
press and release the two control keys at the same time.
The LED will start flashing green: wait until it turns off.
K4570CW Master, wireless In&Out scenario control
5
5

1312
Living Now with Netatmo
Installation Manual
Check that the LEDs of all the devices immediately turn off: the connected devices are now
associated with each other.
1 2
Note: if the LEDs of any devices stay red, disconnect the power from the system, reconnect it, wait a
minute and then repeat the procedure from item 4.

14
Living Now with Netatmo
Installation Manual
After associating the K4570CW Master wireless scenario control, it is possible to activate the IN/
OUT scenarios that can be controlled by the same.
K4570CW upper key for IN scenario.
K4570CW lower key for OUT scenario
Following the procedure below, it is also possible to add other K4570CW scenario controls or the
K4574CW Night/Day wireless scenario control:
Note: the K4574CW wireless scenario control is preset for controlling Night and Day scenarios.
It is then possible to define the actions that will perform these scenarios using the Home + Control App.
Note: after completing the association, wait a few minutes before activating the scenarios.
Shutters SU
No effect on sockets
No effects on lights and relays
Lights and relays OFF
Shutters DOWN
No effect on sockets
BOX
Living
room
Bathroom
Bedroom
Kitchen
Garden
BOX
Living
room
Bathroom
Bedroom
Kitchen
Garden
BOX
Living
room
Bathroom
Bedroom
Kitchen
Garden
BOX
Living
room
Bathroom
Bedroom
Kitchen
Garden

1514
Living Now with Netatmo
Installation Manual
Nota: if the association with the Home + Control App has already been completed, follow the
instructions of the “Add a product to this home” menu in the App, or
Add a connected device
1. Disconnect the voltage from the general switch.
2. Install the new connected device.
OFF
1
3. Reconnect the power supply using the general switch and wait 1 minute for correct system
startup.
ON
3
2

16
Living Now with Netatmo
Installation Manual
1 2
Note: if completed using the App, this procedure will suggest exactly the same sequence of actions
described here.
Check that the LEDs of all the devices are off, with the exception of the device to add, which must
have a steady red LED.
4. Complete the association of the new device as shown in“Associate connected devices”(point 3).

1716
Living Now with Netatmo
Installation Manual
Add a wireless scenario control
1. Start the association:
press and hold down the two control keys at the same time, the LED will turn green. Release
the keys and wait until it turns off.
K4570CW Master, wireless In&Out scenario control
1
1
Check that the LEDs of all the devices immediately turn green steady (with the exception of the
wireless LEDs, which will be off ).
1 2

18
Living Now with Netatmo
Installation Manual
2. Remove the tab from the new control.
4. Press and release one of the control keys: the LED flashes green; release it and wait for the LED
to turn off.
5. End the association:
press and release the two control keys at the same time.
The LED will start flashing green: wait until it turns off.
K4570CW Master, wireless In&Out scenario control
2
3
3. Fit the cover and the plate on the wireless control.
Warning: if cover and plate are not fitted, do not press the wireless control keys.
45
5

1918
Living Now with Netatmo
Installation Manual
Check that the LEDs of all the devices immediately turn off. The control is now associated to your
Smart electric system and you will be able to control the IN/OUT and/or Day/Night scenarios.
You can also add light control K4003CW – K4003DCW – 3577C or rolling shutter control K4027CW
using the following procedure.
1 2

20
Living Now with Netatmo
Installation Manual
1 2
Associate a wireless light/rolling shutter control to one or
more modular connected devices
1. Start the association::
press and hold down the two control keys at the same time, the LED will turn green. Release
the keys and wait until it turns off.
Check that the LEDs of all the devices immediately turn green steady (with the exception of the
wireless LEDs, which will be off ).
K4003CW – K4003DCW – 3577C wireless light control
or
K4027CW wireless shutter control
1
1