Bticino Classe100 V16E User manual

1
www.bticino.com
ST-00000467-
344672
B
AC
A B C
164 mm 165 mm 20,5 mm
2
11
10
3
4*
6
5*
8
1
9
7
EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
2 WIRES handsfree video internal unit with 5”colour LCD display.
It has 2 physical keys for the control of the main video door entry functions – answer
and end a call – and 3 capacitive keys that allow the door lock release, the entrance
panel activation/scrolling and the customisation of most frequently used quick
action – e.g. staircase light control, intercom, additional door lock activation, generic
activations.
The device has a side joystick to adjust: colour, brightness and display contrast, audio
and call tone volume.
There is a call exclusion notification LED.
The installation can be made to the wall using the bracket (supplied) or using table
support to be purchased separately.
Description
Dimensional data
Power supply: 18 – 27 Vdc
Stand by absorption: 10 mA
Max. absorption: 250 mA
Maximum cable section for each clamp: 2 x 1 mm2
Operating temperature: 5 – 40 °C
Technical data
344692 Tabletop support
Related items
Front view
Legend
When pressed, the keys light up and emit a“beep”(that can be deactivated by
procedure).
1. Loudspeaker
2. 5”(16:9) display
3. Bell exclusion notification LED
Red LED flashing: bell excluded
4. Programmable touch keys *
5. Door lock release touch key *
White LED flashing: active Professional Studio (Office) function
6. Entrance panel / scrolling activation touch key
7. Tactile guides for the blinds
8. Communication disabling key
Red LED flashing: call in progre
9. Microphone
10. Staircase light touch key
11. Communication enabling key
Green LED flashing: incoming call
* If the LEDs flash white when pressed, the “safe door lock”function is active and
the key is deactivated.

2
344672
N P M
PM
N
BTICINO
V.le Borri, 231
21100 (VA) ITALY
2 1 5M 1 BUS
2-1
ON OFF
MasterSlave
ON CTS
12
1
2
3
456789
10
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
Configuration
Rear view
Legend
1. Slave / Master function microswitch
2. ON / OFF micro-switch for“safe door lock”function
ON=
To activate the function with device not powered
3. Configurator socket.
4. Line termination ON / OFF micro-switch.
5. Additional power supply enable ON / OFF micro switch
6. 2 wires SCS BUS connection clamps.
7. Clamps for the connection of an external call to the floor pushbutton
PM
N
BTICINO
V.le Borri, 231
21100 (VA) ITALY
Made in Italy
2 1 5M 1 BUS
2-1
ON OFF
8. Additional bell connection clamps (1 - 5M). The connection must be point - point on the clamps of the additional bells
9. Additional power supply clamps (2– 1)
10. Joystick for adjustments and programming
The device must be only physically configured.
N - internal unit number
The configurators connected to the N sockets of the device assign an identification number within the system to each video internal unit. The internal units must be configured in
progressive order. Internal units with parallel connection (max 3 are allowed inside apartments without item 346850) must be configured using the same N configurator. In parallel with
the main video internal unit, additional internal units, video internal units and/or ringtones may be installed.
P – entrance panel association
The configurators connected to the P sockets of the device identify the associated EP, which is the first entrance panel that switches itself on when the pushbutton is pressed the first time,
as well as which door lock is activated when pressing the door lock pushbutton while the video internal unit is idle.
M – operating mode
The configurators connected to the M sockets of the device assign the operating modes to the 4 programmable keys ( , , , ) based on the following indications.
They can also enable special functions .

3
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
MODE KEY FUNCTION NOTES
M = 00
Internal intercom. It sends the call to all the handsets with the same
address.
Activation of the EP (configured with P+1) directly without call or
activation of the actuator 346210 (configured with P+1 and MOD=9)
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
M = 20 Key functions described above + Professional studio
M = 40 Key functions described above + Pager
M = 80 Key functions described above + Professional studio + Pager
M = 01
Internal intercom. It sends the call to all the handsets with the same
address
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface
N=1
N=2
N=2
N=1
Activation of the EP (configured with P+1) directly without call or
activation of the actuator 346210 (configured with P+1 and MOD=9)
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
M = 21 Key functions described above + Professional studio
M = 41 Key functions described above + Pager
M = 81 Key functions described above + Professional studio + Pager

4
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
MODE KEY FUNCTION NOTES
M = 02
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface.
N=1 N=3 N=2 N=1
N=3 N=1
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface.
N=1 N=2 N=2 N=3
N=3 N=2
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
M = 22 Key functions described above + Professional studio
M = 42 Key functions described above + Pager
M = 82 Key functions described above + Professional studio + Pager

5
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
MODE KEY FUNCTION NOTES
M = 03
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface
N=1 N=5 N=2 N=1 N=3 N=1
N=4 N=1 N=5 N=1
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface
N=1 N=2 N=2 N=5 N=3 N=2
N=4 N=2 N=5 N=2
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface
N=1 N=3 N=2 N=3 N=3 N=5
N=4 N=3 N=5 N=3
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface
N=1 N=4 N=2 N=4 N=3 N=4
N=4 N=5 N=5 N=4
M = 23 Key functions described above + Professional studio
M = 43 Key functions described above + Pager
M = 83 Key functions described above + Professional studio + Pager

6
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
MODE KEY FUNCTION NOTES
M = 04 Activation of the EP (configured with P+1) directly without call or
activation of the actuator 346210 (configured with P+1 and MOD=9)
Intercom inside the apartment, in systems with apartment interface
346850, or intercom among apartments in systems without apartment
interface.
N=1
N=2
N=2
N=1
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
M = 24 Key functions described above + Professional studio
M = 44 Key functions described above + Pager
M = 84 Key functions described above + Professional studio + Pager
M = 05 EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
EP door lock release (configured with P+3), directly without call, or
activation of the actuator 346210 (configured with P+3 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+3)
EP door lock release (configured with P+4), directly without call, or
activation of the actuator 346210 (configured with P+4 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+4)
M = 25 Key functions described above + Professional studio
M = 45 Key functions described above + Pager
M = 85 Key functions described above + Professional studio + Pager

7
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
MODE KEY FUNCTION NOTES
M = 06 Preset intercom function with intercommunicating call to the Handset
configured with N=1. From the system handsets it is possible to send
an intercom call to the handset configured with N= 1.The indoor unit
configured with N=1 can receive intercom calls, but is unable to send them.
Internal intercom. It sends the call to all the handsets with the same
address.
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
M = 26 Key functions described above + Professional studio
M = 46 Key functions described above + Pager
M = 86 Key functions described above + Professional studio + Pager
M = 10 General intercom. It sends the call to all the handsets of the system.
Activation of the EP (configured with P+1) directly without call or
activation of the actuator 346210 (configured with P+1 and MOD=9)
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
M = 30 Key functions described above + Professional studio
M = 50 Key functions described above + Pager
M = 90 Key functions described above + Professional studio + Pager
M = 12
Intercom among apartments Xin systems with apartment interface 346850
N=1
Intercom among apartments in systems with apartment interface 346850
N=2
EP door lock release (configured with P+1), directly without call, or
activation of the actuator 346210 (configured with P+1 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+1)
EP door lock release (configured with P+2), directly without call, or
activation of the actuator 346210 (configured with P+2 and MOD=5), or
activation of door lock actuators 346230 - 346260 (configured with P+2)
M = 32 Key functions described above + Professional studio
M = 52 Key functions described above + Pager
M = 92 Key functions described above + Professional studio + Pager

8
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
MODE KEY FUNCTION NOTES
M = 13
Intercom among apartments in systems with apartment interface 346850
N=1
Intercom among apartments in systems with apartment interface 346850
N=2
Intercom among apartments in systems with apartment interface 346850
N=3
Intercom among apartments in systems with apartment interface 346850
N=4
M = 33 Key functions described above + Professional studio
M = 53 Key functions described above + Pager
M = 93 Key functions described above + Professional studio + Pager

9
344672
+
-
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
Device adjustments and settings
Use of the joystick
Using the joystick it is possible to perform adjustments (Adjustments and/or Parameter Adjustment menu during Audio/Video connection) and settings (Settings menu)
You must use the joystick on the side of the device to navigate on the menu and select the settings.
SYMBOL ACTIONS TO BE PERFORMED FUNCTION
Press Confirm/access the Adjustments mode
> 8 sec Press and hold down for more than 8 sec Access the Settings mode
Move the joystick up (when released, it returns to central
position) Previous page/increase level
Move the joystick down (when released, it returns to
central position) Next page/decrease level
Symbol legend

10
344672
OFF
A
OFF
A
EXIT
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
Adjustments
ADJUSTMENTS MENU
From stand-by press the joystick to activate the display
Activate/deactivate the Professional studio-Office function
Adjust the ringtone volume
Exit the menu
Move the joystick up/down to select the page among:

11
ON
A
OFF
A
2
2
1
A
2
2
1
4
4
3
344672
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
RINGTONE VOLUME ADJUSTMENT
From stand-by press the joystick to activate the display and select the
corresponding page
1 Press the joystick to adjust the volume.
The ringtone is played at the set volume level
2 Move the joystick up/down to select the volume level (1 – 8).
4 Move the joystick up/down to select another setting or the last
page to exit
3 Press the joystick to confirm the setting or wait for the timeout
The minimum level corresponds to the exclusion of the ringtone.
The corresponding LED flashes red.
ACTIVATE/DEACTIVATE THE PROFESSIONAL STUDIO-OFFICE FUNCTION
When a call is received from the entrance panel, this function automatically activates the associated door lock without the need for pressing the door lock control key.
To enable this function, Classe100 must be configured as shown in the“Configuration / Special functions”section.
Moreover, the function must be enabled as follows.
Note: It cannot be activated together with the Safe Door Lock and the Door Status function
From stand-by press the joystick to activate the display and select the
corresponding page
A Function status notification (ON = enabled, OFF = disabled)
1 Press the joystick to change mode
2 Move the joystick up/down to select another setting or the last
page to exit

12
344672
1
2
2
A
B
3
5
4
4
6
6
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
AUDIO/VIDEO PARAMETER ADJUSTMENTS
During a connection to an internal unit or entrance panel, it is possible to modify the speaker volume and, only for audiovideo devices, the colour, contrast and brightness of the
image.
1 During a connection press the joystick to modify the parameters The page shows the type of parameter (A) and the set level (B)
2 Move the joystick up/down to select the type of parameter for
which you want to modify the value (see the following table)
ICON TYPE OF PARAMETER
Speaker volume Parameter that can be adjusted only with active audio
Image brightness
Image contrast
Image colour
4 Move the joystick up/down to select the desired level
6 Move the joystick up/down to select another parameter or the last
page to exit
3 Press the joystick to modify the level
5 Press the joystick to confirm or wait for the timeout

13
344672
ON
ON
EXIT
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
From stand-by, press and hold down the joystick for about 8 seconds to
activate the display and access the Settings menu.
Enable/disable the key sound
Associate a ringtone to an event
Exit the menu
Move the joystick up/down to select the page among:
> 8 sec
Settings
SETTINGS MENU

14
344672
ON
1
OFF
2
2
1
01
0
2
2
A
A
B
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
ENABLE/DISABLE THE KEY SOUND
With the basic configuration, when keys are pressed a BEEP is emitted. This function may be disabled/enabled as follows.
From stand-by, press and hold down the joystick for about 8 seconds
to access the advanced menu and select the corresponding page
A Function status notification (ON = enabled, OFF = disabled)
1 Press the joystick to change mode
2 Move the joystick up/down to select another setting or the last
page to exit
ASSOCIATE A RINGTONETO AN EVENT (CALL)
This page can be used to modify the ringtones associated to the different types of call.
The ringtones played for calls from EP configured with S=2 and S=3 are set by default and cannot be changed.
From stand-by, press and hold down the joystick for about 8 seconds
to access the advanced menu and select the corresponding page
ICON TYPE OF CALL
0
Selection of the call ringtone from the MAIN ENTRANCE PANEL (S =0)
1
Selection of the call ringtone from the SECONDARY ENTRANCE PANEL (S =1)
FLOOR CALL ringtone selection
INTERCOM CALL ringtone selection
EXTERNAL INTERCOM CALL ringtone selection (interface 346850 only)
Press the joystick to associate the first event
The page shows the type of call (A) and the current ringtone number (B)
2 Move the joystick up/down to select the type of call for which you
want to set the ringtone (see the following table)

15
344672
01
3
15
5
15
4
4
15
6
6
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
4 Move the joystick up/down to select the ringtone to be associated
(the ringtone is played)
6 Move the joystick up/down to select another call or the last page to
exit
3 Press the joystick to continue
5 Press the joystick to confirm or wait for the timeout
This function can be used to send voice messages using the microphone of the Classe 100 through the speakers of the sound system.
To enable this function, Classe100 must be configured as shown in the“Configuration / Special functions”section.
Function use
From stand-by
PAGING function
Broadcast the message Press the key to end
This function notifies the status of the Door lock. If open the“LED Door lock”flashes, and if closed, the LED stays off.
Warning: the function can only be activated if required by the system - accessory devices are required.
Note: It cannot be activated together with the Professional Studio (Office) function.
DOOR STATUS function

16
344672
25-35 cm
4
0
cm
PM
N
BTICINO
V.le Borri, 231
21100 (VA) ITALY
2 1 5M 1 BUS
2-1
ON OFF
MasterSlave
ON CTS
12
P
N
Slave
ON CTS
12
ST-00000467-EN 08/07/2019
Classe100 V16E Handsfree video internal
unit with Inductive loop
When active, this function prevents the opening of the entrance panel door lock when the internal unit is in stand-by.Therefore, the opening of the door lock is only permitted when
entrance panel and internal unit are in voice communication.
Note: when the function is active, all the keys in all the configurations requiring the activation of a door lock are disabled, and when they are pressed the white LED flashes.
Note: It cannot be activated together with the Professional Studio (Office) function.
Enabling the function
SAFE DOOR LOCK function
Move the corresponding microswitch to ON
INDUCTIVE LOOP use
The inductive loop function enables the device to be used by people wearing hearing aids with (T) selector.
Switch the acoustic device to the T position. To ensure correct magnetic coupling between the handset and the acoustic device, we recommend a position in front of the device, at a
distance of 25-35 cm.
NOTE: the presence of metal and background noise generated by electric/electronic devices (e.g. computer) may compromise the performance and the quality of the coupling device.