Bticino HS4434 User manual

1
TECHNICAL SHEETS
HD/HC/HS4434 - L/N/NT4434N - AM5434
BT00476-a-UK
230 V
Max. 400 W 1,7 A 400 VA 1,7 A
Min. 40 W 0,2 A 40 VA 0,2 A
110 V
Max. 200 W 1,7 A 200 VA 1,7 A
Min. 20 W 0,2 A 20 VA 0,2 A
230 V
Max. 400 VA 1,7 A
Min. 40 VA 0,2 A
110 V
Max. 200 VA 1,7 A
Min. 20 VA 0,2 A
Detector switch - PIR
This device enables a light source to be controlled automatically by
detection of movement in the monitored area.
Movement detector and daylighting measurement with 180° detection angle.
Detection type: infrared (PIR)
Mounting type: wall
Number of terminals: 3
Type of terminals: screw
Terminal capacity: 2 x 2,5 mm2
Stripping length: 8 mm
Pressing the auxiliary control enables the load to be switched on or off manually. If the
control is not pressed, the detector will cut off the load at the end of the time delay or
when the light level threshold has been reached.
Description
Legend
PIR Detector/ Sensor1.
LEARN LED2.
Setting potentiometers3.
ON-OFF button4.
LEARN button5.
Motion LED (under lens)6.
Infrared transceiver (under lens)7.
Daylight sensor8.
Voltage: 100 - 240 V~
Frequency: 50 / 60 Hz
No load power consumption: 0,2 W
Outlet via normally open contact connected to the phase
Wiring: 2 x 2,5 mm2
Flush-mounting box: 40 mm mini
Weight: 60 g
Impact resistance: IK04
Penetration by solid and liquid matter: IP20
Usage temperature: - 5 °C à + 45 °C
Storage temperature: - 20 °C à + 70 °C
Technical data
Front view
1275 lux30 mn 5 lux5 s.
1
6
7
8
2
3
4
5
Dimensional data
45 mm
45 mm
51 mm
Wiring diagrams
100 m max.
1Incandescents, halogen lamps
2Halogen lamps with electronic
transformer
3Halogen lamps with ferroma-
gnetic transformer
1 2
3

2
TECHNICAL SHEETS
HD/HC/HS4434 - L/N/NT4434N - AM5434
BT00476-a-UK
≥ 2,5 m
1 m
2,5 m
Positioning the detector
Installation
The detector must be
positioned in such a way
that it is not disturbed
by the artificial light that
is already present in the
room.
Parameters of detection:
Configuration
Time delay: Lenght of time the load is kept “on”after the last detection.
Sensitivity: Detection range setting.
Modes:
Auto on/Auto off mode:
Automatic switch-on:
- On detection of presence if the natural light level is insufficient.
Automatic switch-off:
- If no presence is detected and at the end of the time delay set.
- Or if the natural light level is sufficient (activated setting range).
Another detection causes automatic switch-on if there is insufficient light.
Walkthrough:
- If a presence is detected for less than 20”, the product will cut off the load after
3 minutes.
- Otherwise, the device will cut off the load at the end of the time delay set.
Manual on/Auto off mode:
Manual switch-on, automatic switch-off:
- When no presence is detected and at the end of the time delay set.
After a switching off, if the sensor detects a presence within 30 seconds it
automatically turns on again the light; after 30 seconds the light has to be
manually turned on.
Sensor parameters Default value Modifiable parameters Configuration tools
BMSO4001 BMSO4003
Time delay 15 mn initially
Tripper position
3, 5, 10, 15, 20 min −
5s - 59 min 59s −
Sensitivity PIR (very high) Low, medium, high, very high
Modes
Auto on/Auto off Inactive Activate/Deactivate
Walkthrough Inactive Activate/Deactivate
Manual on/Auto off Active Activate/Deactivate
Detection
system
Initial PIR Non-modifiable −
Maintain PIR Non-modifiable −
Retrigger PIR PIR/Deactivate −
Alert Inactive Activate/Deactivate −

3
TECHNICAL SHEETS
HD/HC/HS4434 - L/N/NT4434N - AM5434
BT00476-a-UK
Height
Performance
1,2 m
m
6
4 5 8
8 m (PIR)
5 m (PIR)
3 m
(PIR)
≈ 6 m
(PIR)
Modification of the parameters by the configuration tools
• BMSO4001 : Advanced configuration tool
• BMSO4003 : Simplified configuration tool
When the detector receives an IR command via a configuration tool, it emits a beep
confirming that the modification has been taken into account.
Return to factory settings:
1st press: Short press on LEARN, the LED flashes slowly.
2nd press: Press and hold down LEARN for 10 seconds until the LED flashes quickly.
Detection system:
Initial detection: The load is switched on as soon as the first detection occurs if the
natural light level is below the light level threshold.
Maintain: The load remains active if another presence is detected.
Light level parameters:
Light level threshold:Value at which the load comes on if the light level is
below the setting and goes off if it is above this threshold.
Advanced mode:
Calibration:The surrounding light level measured with a luxmeter must then be
transmitted to the detector.
Retrigger: In manual mode. Function allowing automatic switch-on of the product
after a period of 30 seconds following the load being switched off.
After it has been switched off, another detection within a 30-second period triggers
automatic switch-on.
After more than 30 seconds the device must be switched on manually.
Alarm: An audible signal is emitted before the device is switched off (1 minute,
30 seconds and 10 seconds before switch-off).
Light regulation: Automatic switch-off of the load 10 minutes after the light
level threshold is exceeded combined with an additional safety threshold (to
avoid unintended switch-off).
Provision of light: Quantity of additional lux provided by the load being
switched on.
Sensor parameters Default value Modifiable parameters Configuration tools
BMSO4001 BMSO4003
Light level threshold 300 lux initially
Tripper position
20, 100, 300, 500, 1000 lux −
0 - 1275 lux −
Advanced
mode
Calibration − 0 - 99995 lux −
Light regulation Inactive Activate/Deactivate −
Provision of light Auto Auto - 1275 lux −

4
TECHNICAL SHEETS
HD/HC/HS4434 - L/N/NT4434N - AM5434
BT00476-a-UK
Keep the lens clean.
Clean the surface with a cloth.
Do not use: acetone, tar-removing cleaning agents or trichloroethylene.
Maintenance with the following products: - Hexane (En 60669-1)
- Methylated spirit
- Soapy water
- Diluted ammonia
- Bleach diluted to 10%
- Window-cleaning products
Maintenance
Attention : An initial test is required for the use of other special maintenance
products.
Directive: CE
Installation standards: NFC 15-100
Product standards: IEC 60669-2-1
Environmental standards:
- EU directive 2002/96/EC: WEEE (Waste Electrical and Electronical
Equipment).
- EU directive 2002/95/EC: RoHS (Restriction of Hazardous
Substances).
- Regulations: ERP (public buildings)
ERT (workplace buildings)
IGH (high-rise buildings)
Standards