Burrow HEIST User manual

HEIST
Assembly Instructions

32
Parts and hardware Thanks for bringing Burrow into your home.
Everything we make is incredibly simple to
set up, including your new dresser. You’ll
need an extra set of hands, so be sure to
grab a friend before you get started.
1 x
Bottom panel
1 x
Top panel
2 x
Back panels
1 x
Left wall panel
with glides
1 x
Right wall panel
with glides
1 x
Middle panel with
glides
2 x
Corner blocks
4 x
Legs
1 x
Center leg
6 x
Drawer bottoms
6 x
Drawer backs
3 x
Right drawer fronts
3 x
Left drawer fronts
6 x
Drawer right sides
6 x
Drawer left sides
1
Begin with the bottom panel upside-down on
a soft surface, like a carpet or the flattened
cardboard box. Try to set up the dresser as
close to its final position as possible.
2
Screw all five legs into the threaded inserts
on the bottom panel. The center leg does not
have a rubber foot like the other four.
Build the case

54
5
Insert the first back panel (the one without
holes) intothe grooves on the left and right
walls, with the stickers facing inward, and fit
the dowelsintothe holes on the back edge
of the bottom panel. Insert the second back
panel ontop of the first one.
6
Take the top paneland line up the back
edge, with the recessed slot, with the back of
the unit. Fit the slots on the sides of the panel
over the plastic tabs protruding from the tops
of the vertical panels. Push the top panel
toward the back ofthe unit to lock it in place.
3
Flip thebottom panel upright onitslegs.
4
Grab the wall panels and the middle panel.
With a partner, lower theplastic tabs into the
slots on the bottom panel. Then, push each
panel toward the front of the unit to lock
them in place.
9
From the back, thread the anti-tip cable
through the two holes on the top corners of
the back paneland close the clasp so it stays
in place.
7
Grab the two corner blocks and insert the
plastictabs into the slots on the inside top
corners of the unit,then push them out
toward the wall panels tolock them in place.
8
Move the case to its approximate final
position againsta wall.Reach inside and
usea pencil to mark points on the wall
through the two holes on the top corners
of the back panel. This is where you’ll install
anti-tip hardware.

76
1
Place a drawer front on a soft surface with
the slots facing up.
2
Grab a left and right drawer side and insert
the plastic tabs into the corresponding slots.
Assemble your drawers
5
Attach the drawer back by fitting the pins
on the drawer sides into the holes on the
drawer back. Important: this connection is
permanent, so please be careful!
6
Repeat for all of your drawers.
3
Push the drawer sides toward the groove-
less edge of the drawer front to lock them
into place.
4
Slide the drawer bottom into the grooves
all the way around the inside of the sides
and front.

98
1
Starting with the bottom, pull the first two
glides out, and switch the black locking
flipper to the open position, as shown.
For safety, you’ll only be able to open
one drawer at a time.
2
Lower a drawer over the glides, and reach to
fit the hook on the glide into the hole on the
back of the drawer. Make sure the drawer fits
evenly into the glides and is lined flush with
the edge of the dresser.
Attach drawers to glides 3
Gently lower the front of the drawer onto the
metal pin at the front of the glides, then press
the plastic switch in, toward the edge of the
drawer, to lock it in place.
4
Repeat for the rest of your drawers.

1110
2
Unclasp the anti-tip cables, thread them
through the eye of the wall screws, and close
the clasp again.
Install anti-tip hardware Make adjustments
Raise or lower your drawers by turning
the plastic knob on the inside of each
runner next to the pin.
Remove the drawers by disengaging the
plastic switch on the glides, lifting up
slightly, then pulling out.
Twist the foot of the legs to adjust
height and compensate for uneven floors.
1
Insert an included drywall anchor in each
of the marked points,then thread the wall
screws into the anchors using the hex wrench.
2 x
Tether cord
2 x
Wall screw
2 x
Drywall anchor
1 x
Hex wrench

Need help?
Feel free to contact us via email or text
if you have any specific questions!
In the USA:
[e-mail]
[phone]
In Canada:
[e-mail]
[phone]