BWI Eagle AIR-EAGLE XLT 441-8000-R1NC-DC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Receiver
MODEL 441-8000-R1NC-DC
DESCRIPTION
The AIR-EAGLE XLTis an RF system designed for medium to long range
wireless remote control of electrical apparatus in avariety of industrial
applications. Systems can consist of any number of receivers and
handheld or contact input transmitters working together.This receiver is
equipped with 4 independent relays that can switch 5 amps @ 120VAC or
30VDC. The relays are user programmablefor momentary or
toggle/latching operation andcan be directly interfaced with the
customer's equipment or P.L.C. Seven user selectable frequencies allow
multiple systems to be used inthe same area. Capable of receiving
remote signals transmitted from up to 2500 feet away (with the handheld
transmitter) or up to 2 miles away (withthe contact input transmitter),the
Air-Eagle XLT utilizes spread-spectrum technology and provides the
utmost security and reliability even in the noisiest RF environments.
SERIES FEATURE
The “441” Series features repeating capability. Transmitters can be set
up to send “repeat signal packets”, and any transmitter or receiver
within its range will repeat the signal packet to help propagate
communication over widespread areas.
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
INSTALLATION
DISCONNECT DC Power from all equipment before installation.
1. Mount the AIR-EAGLE XLT RECEIVER in a convenient location.
2. Install relay wiring to terminal strip.
3. Install antenna onto connector located on the right side on the
enclosure.
4. Connect supplied power input cable to your external power source.
TERMINAL STRIP WIRING
1
N/O Relay #1
7
N/O Relay #3
13
(-) 9-36VDC INPUT
2
C Relay #1
8
C Relay #3
14
(+) 9-36VDC INPUT
3
N/C Relay #1
9
N/C Relay #3
4
N/O Relay #2
10
N/O Relay #4
5
C Relay #2
11
C Relay #4
6
N/C Relay #2
12
N/C Relay #4
Relay #1 contacts are shown in their de-energized state. When power is
applied tothe unit, relay #1 will energize. The relay will then de-energize
when a signal is received from the transmitter.
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS AND INDICATORS
.
LED1
Illuminated when power is applied to receiver
LED2
Illuminated when relay #1 is energized
LED3
Illuminated when relay #2 is energized
LED4
Illuminated when relay #3 is energized
LED5
Illuminated when relay #4 is energized
RF1
RF module that receives data from the remote
transmitter
REL1 thru REL4
Four SPDT output control relays
SEL1
Seven dip switches for selecting relay options
and operating frequency

AIR-EAGLE®XLT
900 MHz RF Receiver
MODEL 441-8000-R1NC-DC
RELAY & FREQUENCY SET-UP
The unit is shipped from the factory with SEL1 switches in the open
positions. All four relays will operate as maintained momentary and unitis
receiving commands on frequency one. If you wish to change these
default settings, followthe instructions onthe table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired relay operation and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
Relay #1 momentary (default)
Relay #1 toggle/latch
SW2
Relay #2 momentary (default)
Relay #2 toggle/latch
SW3
Relay #3 momentary (default)
Relay #3 toggle/latch
SW4
Relay #4 momentary (default)
Relay #4 toggle/latch
Maintained Momentary –Relay mimics button or input –when
depressed or closed, relay will be energized; when released, relay de-
energizes
Toggle Latch –Relay changes (and holds) its state each time the
corresponding button or input is depressed or closed.
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
SPECIFICATIONS
DC Input
9-36VDC @ 10 WATTS
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per
channel
Fuse Protected
1 amp
Receiver Range
Up to 2500 feet w/standard antenna
Note: Maxrange figures are estimates,based on free-air terrain with limited sourcesof
interference. Actual range will vary based on transmitting power, orientation of transmitter and
receiver, height of transmitting antenna, height of receiving antenna, weather conditions,
interference sources in the area, and terrain between receiver and transmitter, including, but not
limited to, indoor and outdoor structures such as walls, metal objects, trees, buildings, hills, and
mountains
Receiver Frequency
900 MHz Spread Spectrum
Receiver Channels
Seven independent network frequencies
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
Weight
Approx 2 lbs.
ACCESSORIES
Standard Antenna (Included):
900MHz TNC “Rubber Duck” Antenna
49-1103
High Gain Antennas –
Used to help achieve max range in both non line of sight and line
of sight applications. - Contact BWI Eagle for recommendations
900MHx Thru-Hole Mount Omni Directional Antenna
49-2101
900MHz Magnet Mount Omni Directional Antenna
49-2102
900MHz Omni Directional Antenna
49-3101
900MHz 13dB Yagi Antenna
49-3102
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available
in 5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of Feet)
Bulkhead Extensions –
Used to provide an external antenna connection whenmounting
control unit inside another enclosure
TNC Male to TNCBulkhead Cable Assembly
- Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants theAir-Eagle Remote Control System, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improperinstallation, or improper
testing. This limited warranty, and any impliedwarranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eaglemakes no express warranties beyond
thosestated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss duringshipping and is
responsible for theshipping costs incurred.
DOCUMENT DATE: 12/16/2020 / PRODUCT REV. 5
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com