BWI Eagle AIR-EAGLE XLT PLUS Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT PLUS
900MHz RF Receiver
MODEL 461-20800-AC
DESCRIPTION
The AIR-EAGLE XLTPLUS is an RF system designed for long range
wireless remote control of electricalapparatus in avariety of industrial
applications. Systems can consist of any numberof transmitters and
receivers working together. This receiver is equipped with 8independent
relays thatcan switch 5 amps @ 120VAC or 30VDC andcan be directly
interfaced with the customer's equipment or P.L.C. Eight user selectable
frequencies allowmultiple systems to be usedin the same area. The Air-
Eagle XLT Plus can receive remotesignals transmitted from up to 5000
feet away (with a handheld transmitter) or up to 10 miles away (with a
stationary transmitter and external antennas)..
SERIES FEATURE
The “461” series features built-in repeating capability. Each receiver
accepts and performs commands from the transmitterthen repeatsthe
commands to any other receiver within its range. When using multiple
receivers this increases range and reliability because if there is a receiver
that the transmitter can’t quite reach but is within range of another receiver
that HAS gotten the signal, it will still get its command from that receiver.
INSTALLATION
DISCONNECT AC Power from all equipment before installation.
1. Mount the AIR-EAGLE XLT PLUS RECEIVER in a convenient location.
2. Install relay wiring to terminal strip.
3. Install antenna onto antennaconnector located onthe right side on
the enclosure.
4. Connect supplied power input cable to your external power source.
TERMINAL STRIP WIRING
1
N/O Relay #1
10
N/O Relay #4
19
N/O Relay #7
2
C Relay #1
11
C Relay #4
20
C Relay #7
3
N/C Relay #1
12
N/C Relay #4
21
N/C Relay #7
4
N/O Relay #2
13
N/O Relay #5
22
N/O Relay #8
5
C Relay #2
14
C Relay #5
23
C Relay #8
6
N/C Relay #2
15
N/C Relay #5
24
N/C Relay #8
7
N/O Relay #3
16
N/O Relay #6
8
C Relay #3
17
C Relay #6
9
N/C Relay #3
18
N/C Relay #6
AC POWER INPUT
Terminal #1
100-250 VAC
Terminal #2
100-250 VAC
DC powered unit pictured
CONTROLS & INDICATORS
POWER LED
(LED1)
Dual color LED. Illuminates red while receiver is
booting up; changes to green when boot-up is
successful and unit is ready to operate. If this LED
fails to turn green, power unit off for 15-20 seconds,
then reapply power.
RELAY LEDS
Illuminated green while relay is energized
DIP SWITCHES
(SEL1)
Switches used to set user-selectable options and/or
network frequency
EEPROM CHIP
(IC1)
Socket mounted integrated circuit that holds unit’s
program
RF MODULE
(RF2)
RF Module that sends/receives data from our
transmitters/receivers

AIR-EAGLE®XLT PLUS
900MHz RF Receiver
MODEL 461-20800-AC
OPTIONS & FREQUENCY SET-UP
This unit is shipped from the factory with the SEL1 switches in the open
positions. If you wish to change the default settings, follow the instructions
on the table below.
1) Remove power from unit and remove top cover.
2) Select desired relay operation and/or network frequency using table
below.
3) Reattach cover and apply power. Programming is now complete.
UNIT CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
Relays #1 thru #8
maintained momentary
(default)
Relays #1 thru #8
toggle/latch
Maintained Momentary –Relay mimics button or input –when
depressed or closed, relay will be energized; when released, relay de-
energizes
Toggle Latch –Relay changes (and holds) its state each time the
corresponding button or input is depressed or closed.
SW2
Not used on this model
SW3
Vibrating Feedback OFF
(default)
Vibrating Feedback ON
SW4
Relays respond to channel
1 thru 8 commands
(default)
Relays respond to channel
9 thru 16commands
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
GENERAL OPERATION
Relays #1 thru #8 energize or de-energize based on specific
commands from a handheld or contact input transmitter.
BUTTON OR
INPUT
ACTIVATED
RELAY OPERATION
"1"
Relay #1 energizes,maintained momentary
"2"
Relay #2 energizes, maintained momentary
"3"
Relay #3 energizes, maintained momentary
"4"
Relay #4 energizes, maintained momentary
“5”
Relay #5 energizes, maintained momentary
“6”
Relay #6 energizes, maintained momentary
“7”
Relay #7 energizes, maintained momentary
“8”
Relay #8 energizes, maintained momentary
DIMENSIONS
APPROVALS
United States (FCC)
OUR-9XTEND
Canada (IC)
4214A-9XTEND
SPECIFICATIONS
AC Input
100-250 VAC, 5 W, 50/60 Hz
Fuse Protected
2 amp
Relay Contacts
SPDT 5 amp @ 120VACor 30VDC
Receiver Range
Up to 1 Mile with Rubber Duck Antenna /
Up to 10 Miles with External Antenna
Note: Maxrange figures are estimates,based on free-air terrain with limited sourcesof
interference. Actual range will vary based on transmitting power, orientation of transmitter and
receiver, height of transmitting antenna, height of receiving antenna, weather conditions,
interference sources in the area, and terrain between receiver and transmitter, including, but not
limited to, indoor and outdoor structures such as walls, metal objects, trees, buildings, hills, and
mountains
Receiver Frequency
900 MHz Spread Spectrum
RF Networks
Eight Independent Network Frequencies
Enclosure
Hinged fiberglass with window / NEMA 3,
3R, 4, 12, 13
Operating Temp
-40oF to +185oF

AIR-EAGLE®XLT PLUS
900MHz RF Receiver
MODEL 461-20800-AC
ACCESSORIES
Standard Antenna (Included):
900MHz TNC “Rubber Duck” Antenna
49-1103
Mobile/Base Antennas –
Used to help achieve max range in both nonline of sight andline of
sight applications. - Contact BWI Eagle for recommendations
900MHz Thru-Hole Mount Mobile Antenna
49-2101
900MHz Magnet Mount Mobile Antenna
49-2102
900MHz Omni Directional Base Antenna
49-3101
900MHz Yagi Directional Base Antenna
49-3102
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available in
5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of Feet)
Bulkhead Extensions –
Used to provide an external antenna connection whenmounting
control unit inside another enclosure
TNC Male to TNCBulkhead Cable Assembly
- Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle XLT Remote Control System, if
properly used and installed, will be free from defects in material and
workmanship for a period of 1 year after date of purchase. Said warranty
to include the repair or replacement of defective equipment. This
warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with
productinstructions, misuse, neglect, alteration, repair, improper
installation, or improper testing. This limited warranty, and any implied
warranties that may exist understate law, apply onlyto the original
purchaser of the equipment, and last only for as long assuch purchaser
continues to own the equipment. This warranty replaces all other
warranties, express or impliedincluding, but not limited to, the implied
warranties or merchantability and fitness for a particular purpose. BWI
Eagle makes no express warranties beyond those stated here. BWI
disclaims without limitation, impliedwarranties of merchantability and
fitness for a particular purpose. Some jurisdictions do not allow the
exclusion of implied warranties so this limitation may not apply to you. To
obtain warranty service, contact BWI Eaglefor a return material
authorization. When returning equipment toBWI Eagle,the customer
assumes the risk of damage or loss duringshipping and is responsible for
the shipping costs incurred.
DOCUMENT DATE: 10/14/2021 /PRODUCT REV. 4
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com