C.R. Plastic Products Generation Line TB01 User manual

Product: 17" Cocktail Legs (TB01) with either 32" Round Table Top (TT01) or 37" Round Table Top (TT02)
Your purchase and who is C. R. Plastic Products Inc.?
Parts You will need:
1. Two sets of Legs. (A) 1. Drill
2. Two Long Stringers (B)
3. Two Short Stringers ( C)
4. Table Top (D)
1)
2)
3)
4)
C. R. Plastic Products Inc. is an environmentally conscious Canadian company. Our "Generation Line" of recycled
furniture will give you years of comfort, style and maintenance free enjoyment. You will find your furniture to be
waterproof and durable. By choosing this product, you are saving generations of trees and are reducing the burden on
our landfill sites. Thank you for purchasing from C. R. Plastic Products Inc.
Step 3: Take the second set of Legs (A) and attach them to the opposite ends of the
stringers using 2½" screws. The assembled Legs should taper outwards as shown in
the picture at Step 4.
Step 4: Place the Table Top (E) upside down with the frame facing up. Slide the
Short Stringers (C) into the slots of the frame. Be sure to center the legs
approximately 8¼" from the outside edges of the table. Attach the legs to the table
top using four 2" screws.
Step 2: Take one of the Long Stringers (B) and line it up with the counter sunk holes
on the leg. Attach with 2½" screws. Repeat on the other side.
Before starting set the 4 - 2" screws aside for use in Step 4.
Step 1: Take one of the Legs (A) with the countersunk holes facing you. Take a
Short Stringer (C) with the countersunk holes facing down the table legs (This is the
longer side of the stringer). The holes on the stringer are offset and should be closer
to the outside of the frame. Line the stringer up flush with the top of the leg. Attach
the stringer using the 2½" screws. Repeat on the other side. The assembled Legs
should taper outwards as shown in the picture at Step 4.
5. Bag of #8 Screws
(16 - 2½" and 4 - 2")
2. #2
Robertson
(square)
or Phillips
bit.
crpproducts.com
Proudly Made In CANADA

Product: 37" Pub Table Legs (TB03) with either 32" Round Table Top (TT01) or 37" Round Table Top (TT02)
Your purchase and who is C. R. Plastic Products Inc.?
Parts You will need:
1. Two sets of legs. (A) 1. Drill
2. Two long stringers (B)
3. Two medium stringers (C)
4. Two small stringers (D)
5. Table top (E)
6. Bag of screws (24 - 2½", 4 - 2")
1)
2)
3)
4)
C. R. Plastic Products Inc. is an environmentally conscious Canadian company. Our "Generation Line" of recycled
furniture will give you years of comfort, style and maintenance free enjoyment. You will find your furniture to be
waterproof and durable. By choosing this product, you are saving generations of trees and are reducing the burden on
our landfill sites. Thank you for purchasing from C. R. Plastic Products Inc.
Step 1: Take one of the legs (A), counter sunk holes facing you, and the small
stringers (D). Take one of the small stringers, counter sunk holes facing the bottom
of the table. The holes on the stringer are offset and should be closer to the outside
of the frame. Attach the small stringer (D) using 2½" screws. Repeat on the other
side.
Step 2: Take one of the medium stringers (C) and line it up with the middle set of
holes and attach using 2½" screws. Take one of the long stringers (B) and line it up
with the bottom holes and attach using 2½" screws. Repeat to the other side .
Step 3: Take the second set of legs (A) and attach them to the opposite ends of the
stringers using 2½" screws.
Step 4: Place the table top (E) upside down with the frame facing up. Slide the small
stringers (D) into the slots of the frame. Be sure to center it the legs approximately
8¼" in from the outside edges. Attach the legs to the table top using four 2” screws.
2. #2 Robertson
(square) or Phillips
bit.
crpproducts.com
Proudly Made In CANADA