Calimet CM-5-ACFP User manual

1

2
PRODUCT SPECS：
Voltage Input：110V
Maximum output current：15AM，Fuse: AC110V 15AM
Remote control distance： Open space >150 Feet (50 meters)
WARNING
To reduce the risk of INJURY or DEATH:
 Never let children operate or play with gate control, keep remote control
away from children.
 ALWAYS keep people and objects away from gate. NO ONE SHOULD CROSS
THE PATH OF MOVING GATE.
 Test gate operator monthly. The gate MUST reverse in contact with a rigid
object of reverse when an object activates the non-contact sensors. After
adjusting the force or limit of travel, reset gate operator. Failure to adjust
and reset the gate operator properly can increase the risk of INJURY or
DEATH.
 Use the emergency release ONLY when gate is not moving.
 KEEP GATE PROPERLY MAINTAINED. Read owner’s manual. Having a
qualified service person make repairs to gate hardware.
 The entrance is for vehicles ONLY. Pedestrians MUST use separate
entrance.
 SAVE THESE INSTRUCTIONS.

3
Installation of Base
1. Lay out position of 6 Anchors by measuring clearance between anchors
and inside edge of gate. Figure 1
2. Install underground conduits in area for conduits. Figure 2
Figure 1 Figure 2

4
Installation Barrier distance
Figure 3
Figure 4

5
Position of gate and operator
Two options of chain connection.
Figure 5 Front Mount
Figure6 Rear Mount

6
Welding Bracket of Chain
Figure 7
Correct connection of chain
Figure 8
Figure 8. Follow the correct way to install chain. Incorrect installation will cause
malfunction of operator and potential damages.

7
Power Connection
Figure9
1. MUST us UL proved power wires, power wires MUST have minimum capacity
for 25 Am current.
2. All operators MUST properly grounded in order to prevent electrical charge.
Must use dedicated circuit for power supply.
3. When power connected, turn power switch in operator to ON position.

8
EMERGENCY RELEASE
Figure 10
A. Emergency Release of gate
1. Disconnect power.
2. Push Release pedal downward and move slightly to the right until it was locked in down
Position.
3. Hold and push gate to desired direction.
B. Reset pedal (Only when operator has No reaction while using remote control)
1. Push pedal downward from locked position and slightly move to the left, unlocked
Pedal.
2. Allow Pedal rise up to reset position and release pedal.

9
Entrapment protection
Safety and Exit loop
Figure 11

10
Control Board lay out
Figure 12

11
Gate Travel Limit Adjustment
Figure 13
Turn up or down of both wheels to adjust distance between them, making gate stop at the
position desired.

12
Use Remote Control
Device
Figure 12
There are two modes to set Remote Control: Self-study Mode& Numeric Mode
 Self-study code may be set up to 60 groups.
A. Self-study mode corresponds to receiver in control board. Press and hold STUDY key
for 3 seconds until flashing light turn to solid bright, press any key on Remote Control until
STUDY light turn to flashing again, setting done. Repeat above if additional code needed.
B. Existing Codes removal. Press STUDY key and hold for 8 seconds, watching light state:
flashing-solid-flashing, setting done. All existing Self-study codes have been removed.
 Numeric Mode
A. First to turn SW9 key to ON position, now control board activated.
B. Make a combination of code. On SW8, Set an 8-digi combination to match identical 8-digi
combination on Remote Control. Note: each switch could be placed on up, middle and low
position. No limit of groups of combinations.
C. On switch SW10, KEY 1 and KEY 2 are used for 2-buttom model of remote controls. Note: if
KEY 1 code was set corresponding with BUTTON ONE on remote control, then KEY 1 will NOT
work with BUTTON TWO on remote control.

13
Use DIP Switches
Figure 15 DIP switch
1. TIMER: 1-60S Timer: Auto activated to close gate upon set time ( 1~ 60 seconds).
2. RADIO: Remote control radio receiver, allow remote control to close gate without timer
activation.
3. OSC: Remote control priority. Allow remote control to direct gate movement whenever
gate is moving in any direction. First signal stop gate, second signal move gate to opposite
direction.
4. LOCK: Use for lock or unlock gate. When switch ON, The LOCK in Control board (Left edge
Figure 12) will be available to output 115 V power.
5. 1 PASS: Anti-tailgating system. It corresponds to underground safety loop. when ON
selected, Once the vehicle has cleared safe loop outside of property, gate start to close
immediately without opening to limit. If second vehicle across loop at this time, gate will stop.
The second vehicle must get off the loop and then gate continue to close completely.
6. SLAVE: Secondary operator activation.
7. BRAKE: Use to slow down movement of gate when it is reaching limit of open or close.
8. OPEB L/R: Choose gate open direction Left or Right

14
Use Infrared Control
Figure 16
Follow infrared control instruction to connect power. Common wire connected to Common
pole, Signal wire connected to OPEN or CLOSE pole.
Use of External Receiver
Figure 17
Ports on external receiver are marked as 1, 2, and 3. NO: 1 is COMMON pole, NO: 2 is RELAY
pole, NO: 3 is 24 VDC

15
Slave operator activation
Figure18
1. Set SLAVE switch on SLAVE CONTROL BOARD to ON position.
2. Use UL proved electric wire connect DATA- and DATA- from Master control board to
Slave control Board, then connect DATA+ and DATA+ accordingly.
3. M/LINK light turn to solid bright.
Use Reversing Device
Figure 19
1. CLOSE ERD: when closing gate, increase/decrease amount of force by turning knob
Clockwise/counter clockwise.
2. OPENERD：When opening gate, increase/decrease amount of force by turning knob
Clockwise/counter clockwise.
3. Test device sensitivity every 6 months.

16
Remote Control & Timer Delay Closing
Figure 20
A. Remote Control delay closing
1. Choose time delay to activate operator between 0~6 seconds by turning knob on DELAY
B. Timer automatic delay closing
1. On DIP switch Set key TIMER to ON position (Figure 15 )
2. Adjust knob on TIMER between 0~60 seconds to activate operator. (Figure 20 )