Calimet CM3-ACFP User manual

www.calimetco.com
9949 Hayward Way South El Monte CA 91733
Tel: (626) 452 - 9009

1
PRODUCT SPECS：
Voltage Input ： 110V
Maximum output current ： 15AM, Fuse: AC110V 15AM
Remote control distance ： Open space >150 Feet (50 meters)
Maximum Gate weight: 1000 LBS
Maximum Gate length: 22 FEET
WARNING
To reduce the risk of INJURY or DEATH:
Never let children operate or play with gate control or around gate, keep
remote control away from children.
ALWAYS keep people and objects away from gate. NO ONE SHOULD CROSS
THE PATH OF MOVING GATE.
Test gate operator monthly. The gate MUST reverse in contact with a rigid
object of reverse when an object activates the non -- contact sensors. After
adjusting the force or limit of travel, reset gate operator. Failure to adjust
and reset the gate operator properly can increase the risk of INJURY or
DEATH.
Use the emergency release ONLY when gate is not moving.
KEEP GATE PROPERLY MAINTAINED. Read owner’s manual. Have a certified
service person to make repairs or install operator hardware.
The entrance is for vehicles ONLY. Pedestrians MUST use separate
entrance.
SAVE THESE INSTRUCTIONS.

2
Installation of Base
1. Lay out position of 6 Anchors by measuring clearance between anchors and
inside edge of gate. Figure 1
2. Install underground conduits in area for conduits. Figure 2
Figure 1 Figure 2

3
Installation Barrier distance
Figure 3
Figure 4

4
Position Of Gate and Operator
Two options for chain connections:
Figure 5 Rear Mount
Figure 6 Front Mount

5
Welding Bracket of Chain
Figure 7
Correct connection of chain
Figure 8
Figure 8. Follow the correct way to install chain. Incorrect installation will cause
malfunction of operator and potential damages.

6
Power Connection
Figure 9
1. MUST use UL proved power wires, power wires MUST have minimum capacity
for 25 Am current.
2. All operators MUST be properly grounded in order to prevent electrical charge.
Must use dedicated circuit for power supply.
3. When power is connected, turn operator power switch to ON position.

7
EMERGENCY RELEASE
Figure 10
A. Emergency Release of gate
1. Disconnect power.
2. Push Release pedal downward and move slightly to the right until it was locked
in.
3. Hold and push gate to desired direction.
B. Reset pedal (Only when operator has No reaction while using remote control)
1. Push pedal downward from locked position and slightly move to the left,
unlocked pedal.
2. Allow Pedal rise up to reset position and release pedal.

8
Entrapment Protection
Safety and Exit Loop
Figure 11

9
Control Board Lay Out
Figure 12

10
Gate Travel Limit Adjustment
Figure 13
Turn up or down of both wheels to adjust distance in between, make gate stop at
the desired position.

11
Use Remote Control
Device
Figure 14
There are two modes to set remote control: Self -- study Mode& Numeric Mode
Self -- study code may be set up to 60 groups.
A. Self -- study mode corresponds to receiver in control board. Press and hold
STUDY key for 3 seconds until flashing light turn to solid bright, press any key on
remote control until STUDY light turn to flashing again, setting now is done. Repeat
above if additional code needed.
B. Existing Codes removal. Press STUDY key and hold for 8 seconds, watching
light state: flashing -- solid -- flashing, setting is done. All existing Self -- study codes have
been removed.
Numeric Mode
A. First to turn SW9 key to ON position, now control board is activated.
B. Make a combination of code. On SW8, Set an 8 -- digit combination to match
identical 8 -- digit combination on Remote Control. Note: each switch could be
placed on up, middle or low position. There is no limit for groups of combinations.
C. On switch SW10, KEY 1 and KEY 2 are used for 2 -- buttom model of remote
controls. Note: if
KEY 1 code was set with BUTTON ONE on remote control; KEY 1 will NOT work with
BUTTON TWO on remote control.

12
Use DIP Switches
Figure 15 DIP switch
1.CL
-- DELAY: Gate Closing delay, switch to ON position, turn timer to 1 - 6 seconds.
2.TIMER: 1 -- 60 Timer: Auto activated to close gate upon set time ( 1~ 60 seconds).
3. OSC: Remote control priority. Allow remote control to direct gate movement
whenever gate is moving in any direction. Use first signal to stop gate, use second
signal to move gate to opposite direction.
4. 1 PASS: Anti -- tailgating system. It corresponds to underground safety loop.
After the vehicle has cleared safe loop outside of property, gate will start to close
immediately without opening to limit, when ON is selected. If second vehicle across
loop at this time, gate will stop. The second vehicle must get off the loop and then
gate will continue to close completely.
5. SLAVE: Secondary operator activation.
6. OPEB L/R: Choose gate open direction Left or Right.
Use Infrared Control
Figure 16
Follow infrared control instruction to connect power. Common wire is connected to
Common pole, signal wire is connected to OPEN or CLOSE pole.

13
Use of External Receiver
Figure 17
External connectors are installed on the rear side of mainboard protector box.
Slave Operator Activation
Figure 18
1. Set SLAVE switch on SLAVE CONTROL BOARD to ON position.
2. Use UL proved electric wire connect DATA - and DATA - from Master control
board to Slave control Board, then connect DATA+ and DATA+ accordingly.
3. M/LINK light turns to solid bright.

14
Use Reversing Device
Figure 19
1. CLOSE ERD: when closing gate, increase/decrease amount of force by
turning knob clockwise/counter clockwise.
2. OPEN ERD：When opening gate, increase/decrease amount of force by
turning knob clockwise/counter clockwise.
3. Test device sensitivity every 6 months.
Remote Control & Timer Delay Closing
A. Remote Control delay closing
Figure 20
1. Choose time delay to activate operator between 0~6 seconds by turning knob
on DELAY
B. Timer automatic delay closing
1. On DIP switch Set key TIMER to ON position (Figure 15 )
2. Adjust knob on TIMER between 0~60 seconds to activate operator (Figure 20)

Calimet Co Inc
9949 Hayward Way
South E1Monte, CA91733
Tel: [phone]
Alternate: 626-482-3066
Fax: [phone]
[email protected]
www.bestirongatemotor.com