Calimet CM7-ACFP User manual

CM7-ACFP
Instruction Manual
www.calimetco.com
9949 Hayward Way South El Monte, CA, 91733 Tel: [phone]
Swing Gate Operator

1
PRODUCT SPECS
WARNING
To reduce the risk of INJURY or DEATH:
•Never let children operate the gate or play around the gate. Keep the remote control away
from children.
•Always keep people and objects away from the gate. Cars, people, and other objects should
never enter when the gate is closing.
•Test gate operator monthly. The gate must reverse when it comes in contact with a solid
object, or stop when an object activates the non-contact sensors. After adjusting the force or
travel limit, re-test the gate operator. Failure to maintain the gate operator properly can
increase the risk of injury or death.
•Use the emergency release only when the gate is not moving.
•Keep the gate properly maintained. Read the owner's manual on how to maintain your gate.
Have a certified service technician make repairs or install gate operator hardware.
•The gate entrance should be used for vehicles only. Pedestrians should use a seperate entrance.
•Keep these instructions.
Voltage Input: 110V
Maximum Output Current: 15 amp, Fuse: AC 110V 15 amp
Remote Control Distance: >150 Feet (50 meters)
Maximum Gate Weight: 2500 lbs
Maximum Gate Length: 25 Feet
•Verify this operator is proper for the type and size of gate.
•Make sure the gate has been properly installed and slides freely in both directions. Repair
or replace all worn or damaged gate hardware prior to installation.
Product Specs

Installation
1. Lay out position of 6 wedge anchors by measuring clearance between anchors
and inside edge of gate. Figure 1
2. Install underground conduits in area for conduits. Figure 2 Wedge Anchor
Step 1: Installing the Base
The base, also known as a pad is a raised platform. We recommend using a concrete base.
1/2" x 3 1/2"
2
Contact local underground utility locating companies before digging more than 12 inches deep to
avoid damaging underound power, gas or other utulity lines.
Size of concrete base
A minimum of 2" on each side of the operator is recommended.

Step 2: Door arm installation
Figure 3
After you're satisfied with testing the arm in the full open and closed positions, weld gate
bracket and arm.
Figure 4
A. Should be at least 1/4 the gate length. NOTE: Uphill or heavy gates should be at least 1/3 gate
length.
B. 14” minimum for open gate clearance (2" thick gate)
C. 27’
D&E Arm should be 90° from gate when open and in the straight "locked" .D=l*0.6,E=l*0.4
Installation
3

A. DO NOT allow the arm to touch the gate operator's hood when the gate is in the open
position. Too much stress is put on the arm in this position during gate operation.
Figure 6
A. Preferred arm position is 90° from the open gate.
B.
Distance between door and machine: 2" min
Installation
Figure 5
C.
4
NOTE: If dimension between open gate and wall is 20" to 32" then compact installation is
necessary. (See Figure 7)

Figure 7
Support bar should be installed at the gate bracket height across the entire gate to keep the
gate pickets from bending.
Installation
5

Figure 8
Figure 9
1. MUST use UL approved power wires, power wires MUST have minimum capacity for 25
amp current.
2. All operators MUST be properly grounded in order to prevent an electrical charge. Must
use a dedicated circuit for power supply.
3. When the power is connected, turn operator power switch to ON position.
Installation
6
Step 3: Connecting the Power

Step 4: Open Position
Installation
7
Open Direction
Choose whether your gate opens left or right.
Dip Switch #6 (Figure 10) on the bottom of the gate operator circuit board
controls the open direction.
On = opens right, Off = opens left
Figure 10
Step 5: Installing the Photo Eye
1. Plug the photo eye cable to the back of the gate opener,
behind the circuit board, Figure 11
2. Press the reset button on the gate operator control board.
3. Mount the photo eye on the stationary part of your gate or a post next
to your gate, about 21" from the ground.
4. Press the orange button on the photo eye to turn on the infrared beam.
5. Mount the reflector to the opposite side. Make sure the infrared beam hits
inside the circle of the reflector. Figure 12
6. Press the orange button on the photo eye to turn off the infrared beam.
Figure 11
Figure 12
Infrared beam
inside circle
Youtube
Youtube video with more details on how to install the photo eye: https://
youtu.be/F7NpB9W_OMY
Plug photo eye
cable here

Installation
Step 6: Gate Travel Limit
This controls the position of where the gate stops when it opens and closes.
1. Use a screwdriver to loosen the nails on the top and bottom limit cams
2. Turn left or right on both limit cams to adjust the position of where the gate opens and closes. Figure 9
TIP: Use the OPEN, CLOSE, STOP buttons on the gate operator circuit board for faster testing
3. Use the screwdriver and screw back in the limit cam nails
Youtube
More detail on travel limit programming: https://youtu.be/_DeVM5dgZPs
Finished! You are now finished installing your gate operator.
Figure 13
8

9
Figure 14
Opening the gate
1. Disconnect power.
2.
Push release pedal downward and move slightly to the right until it is locked in.
3. Hold and push gate to desired direction.
Reset the Pedal
Reset the pedal only when the operator doesn't work while using the remote control.
1. Push the pedal downward from locked position and slightly move to the left.
2. Allow the pedal rise up to the reset position and release the pedal.
Features
EMERGENCY RELEASE
The emergency release allows you to open the gate manually, such as in cases where there is a
power outage and there is no electricity.

Figure 15
Features
Safety and Exit Loop
This is an optional step. If you wish to install a exit loop detector, see figure 15 for the
position of the safety and exit loops.
Entrapment Protection
10

Figure 16
Features
Control Board Layout
This is a picture of the control board. Use this for reference.
Youtube
Circuit board Programming Guide: https://youtu.be/_7iBuKr1ZtY
11

12
Connecting Additional Remote Controls
Figure 17
There are two ways to connect your remote control: Study Mode & Numeric Mode.
Study mode can fit up to 60 different remote controls.
Connect using Study Mode On your gate operator circuit board, look for the study key. Press
and hold the button on the remote control. Press and hold the study key for 1.5-2 seconds.
Done, the remote is now connected to the gate opener.
Removing existing remote controls Press the STUDY key on the gate operator circuit
board and hold for 8 seconds. Done. All remote controls are now removed.
Numeric Mode
A. On your circuit board, turn the SW9 key to the ON position.
B. Unscrew the back of the remote control to gain access to the control board. You
should see 1-8 dip switches. Each switch has 3 positions: up, middle, bottom. Flip
these 1-8 switches to any position you'd like.
C. On the gate opener control board, look for the same 1-8 dip switches, and set the same
combination as you did on the remote.
D. Finished.
Note: On switch SW10, KEY 1 and KEY 2 are used for the 2-button model of remote
controls. Note: if KEY 1 code was set with BUTTON ONE on remote control; KEY 1 will NOT
work with BUTTON TWO on the remote control.
By default, the remote controls are already connected to the gate operator. You do not need
to do any of the following steps unless you are adding more remote controls.
Study Mode
Youtube
Youtube video that explains more on remote control programming:
https://youtu.be/QfT6O4apTI8
Features

Use Infrared Control
Figure 19
Follow infrared control instruction to connect power. Common wire is connected to Common
pole, signal wire is connected to OPEN or CLOSE pole.
13
Features
DIP Switch Features
Figure 18 DIP switch
1. CL-DELAY: Gate Closing delay, switch to ON position, turn timer to 1- 6 seconds.
2.TIMER: 1-60 Timer: Auto activated to close gate upon set time ( 1~ 60 seconds).
3. OSC: Remote control priority. Allow remote control to direct gate movement whenever gate is
moving in any direction. Use first signal to stop gate, use second signal to move gate to opposite
direction.
4. 1 PASS: Anti-tailgating system. It corresponds to underground safety loop. After the vehicle has
cleared safe loop outside of property, gate will start to close immediately without opening to limit,
when ON is selected. If second vehicle across loop at this time, gate will stop. The second vehicle
must get off the loop and then gate will continue to close completely.
5. SLAVE: Secondary operator activation
6. OPEB L/R: Choose gate open direction Left or Right.

Figure 20
Slave operator activation
Figure 21
1. Set SLAVE switch on SLAVE CONTROL BOARD to ON position.
2. Use UL proved electric wire connect DATA- and DATA- from Master control board to Slave
control Board, then connect DATA+ and DATA+ accordingly.
3. M/LINK light turns to solid bright.
14
Features
External Receiver
External connectors are installed on the rear side of mainboard protector box.

Remote Control & Timer Delay Closing
Figure 23
A. Remote Control delay closing
1. Choose time delay to activate operator between 0~6 seconds by turning knob on
DELAY
15
Features
Figure 22
2. CLOSE Sensitivity: Increase/decrease amount of force by turning knob clockwise/
counter clockwise. This is the fourth blue knob on the circuit board. Figure 22, left.
1. OPEN Sensitivity: Increase/decrease amount of force by turning knob clockwise/
counter clockwise. This is the third blue knob in the circuit board. Figure 22, left.
3. Test device sensitivity every 6 months.
Sensitivity
The sensitivity has to do with the weight of the gate, and also other factors. A heavier gate will require
less sensitivity, and a lighter gate will require more sensitivity.
If a gate is too sensitive, the gate may stop or reverse by itself. It it's not sensitive enough, it might
not stop or reverse.
1. On your gate operator circuit board in the bottom, turn Dip Switch #2 to the ON
position. Figure 24
2. On the gate operator circuit board, adjust the delay by turning the second blue knob
from 0-60 seconds. Figure 25
Auto Close
This allows your gate to automatically close after opening it.
Figure 24 Figure 25

9949 Hayward Way South El Monte, CA 91733
Tel: [phone] Alternate: 626-482-3066 Fax: [phone]
Email: [email protected]
www.calimetco.com